Manual/User Guide
Page 1
C141-E261 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E261 3-1 CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E261 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E261 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
... 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The mounting frame is attached. Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero...
... 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The mounting frame is attached. Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero...
Manual/User Guide
Page 4
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E261 if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values;
Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E261 if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values;
Manual/User Guide
Page 5
Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E261 3-5 3.2 Mounting Because of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole mounted to the HDD, do not allow this to block.
Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E261 3-5 3.2 Mounting Because of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 6
... in Table 3.1. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and standard values No. Provide air circulation in the cabinet such that the PCA side, in particular, receives sufficient cooling. Regardless of the DE. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to...
... in Table 3.1. Figure 3.4 shows the temperature measurement point. 1 Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and standard values No. Provide air circulation in the cabinet such that the PCA side, in particular, receives sufficient cooling. Regardless of the DE. Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to...
Manual/User Guide
Page 7
Pressing it by external magnetic fields. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Static: When handling the device, disconnect the body ground (500 kΩ or greater). 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. C141-E261...
Pressing it by external magnetic fields. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Static: When handling the device, disconnect the body ground (500 kΩ or greater). 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. C141-E261...
Manual/User Guide
Page 8
... a low impact when you use the driver of the screw strictly. General notes Wrist strap Use the Wrist strap. Do not stack when carrying. Do not drop. Installation (1) Please use an electric driver. Figure 3.6 Handling cautions - Do not hit HDD each other. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY...
... a low impact when you use the driver of the screw strictly. General notes Wrist strap Use the Wrist strap. Do not stack when carrying. Do not drop. Installation (1) Please use an electric driver. Figure 3.6 Handling cautions - Do not hit HDD each other. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY...
Manual/User Guide
Page 9
Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E261 3-9
Figure 3.7 shows the locations of these connectors and terminals. 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E261 3-9
Manual/User Guide
Page 10
... pins in the signal supply segment segment View from the connectors complying with Serial-ATA Revision 2.5 specification. The connection reliability per number of insertion/extractions varies with the condition of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification...
... pins in the signal supply segment segment View from the connectors complying with Serial-ATA Revision 2.5 specification. The connection reliability per number of insertion/extractions varies with the condition of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5." Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of host system for mating with the disk drive must be compliant with the Serial ATA Revision 2.5 specification...
Manual/User Guide
Page 11
Removing the cable without releasing the SATA interface Latch may lead to remove the cable while releasing the Latch. Accordingly, be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply...
Removing the cable without releasing the SATA interface Latch may lead to remove the cable while releasing the Latch. Accordingly, be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply...