Dewalt DWE7480 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE7480 manuals!
Problems with Dewalt DWE7480?
Ask a Question
Free Dewalt DWE7480 manuals!
Problems with Dewalt DWE7480?
Ask a Question
Most Recent Dewalt DWE7480 Questions
Dad Throat Plate
I would like to buy a dado throat plate for my saw can you give me a part number
I would like to buy a dado throat plate for my saw can you give me a part number
(Posted by kenhenshaw 10 years ago)
Dewalt DWE7480 Videos
Dewalt - DWE7480
Duration: 2:10
Total Views: 378
Duration: 2:10
Total Views: 378
best table saw | DEWALT DWE7480 Table Saw with Site Pro Modular Guarding System | cheap table saw
Duration: 1:28
Total Views: 277
Duration: 1:28
Total Views: 277
Popular Dewalt DWE7480 Manual Pages
Instruction Manual - Page 2
..., CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). Double Insulation
If saw table while the blade is in electric shock, fire and/or serious injury. Repair or replace damaged or worn cord immediately NOTE: Double insulation does not take the place of balance may cover moving parts. The insulation system is of the guarding...
Instruction Manual - Page 3
.... The use .
• ALWAYS lock the fence and bevel adjustment before cutting.
• DO NOT leave a long board (or other part that should be properly repaired or replaced. Consult the instruction manual for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other qualified service personnel if the problem cannot be hazardous when used whenever the...
Instruction Manual - Page 4
... to the nearest authorized DEWALT service center for a particular application...manual and on the table surface and the blade is used , including all thru sawing. d. k. English
• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you return to thru cutting operations. Information is thrown toward the operator. Please refer to guide along the fence...
Instruction Manual - Page 5
... fence
2.
Blade guard assembly
4. Push stick (attached to rip fence)...replace them before starting cut.
Refer to these terms and you read the entire instruction manual. Miter gauge
5. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Specifications
Amperes
15 A
Miter Angle
60° L and R
Bevel Angle
-2° to assemble the tool. Carefully unpack the table saw and all parts...
Instruction Manual - Page 6
...Assembling the Rip Fence (Fig. 3-5)
The rip fence can be in line with this saw .
1. Secure the rip fence by the yellow arrows on the left of your table saw are to the ...AA
FIG. 5
G
To Remove the Throat Plate (Fig. 6)
1. Raise the saw if riving knife is functioning. Check alignment after each change
accessories or make any adjustments. FIG. 8
YY
FIG. 9
FF
C
4.
Mounting ...
Instruction Manual - Page 7
... position. The table saw must be used to make sure table saw and is a concern, the DWE7480 can then be locked in place for mounting. Center the saw . Slide the anti-kickback housing along the top of the throat plate should be used .
If marring the supporting work surface is
available at a local DEWALT dealer or
service center at...
Instruction Manual - Page 8
..., push it from power source before installing and removing accessories, before connecting saw table. To use the narrow ripping fence in position 1 (for alignment instructions. Before
adjusting, be sure switch is... position. Set the blade at 0˚ and 45˚ to 24" ripping). Lock the rail lock lever.
4. WORK SUPPORT EXTENSION/NARROW RIPPING FENCE (FIG. 15, 16)
The table saw . MM...
Instruction Manual - Page 10
... the
wrench on the table against the blade). The riving knife supplied with this table saw blade
beveled to the riving...replacing the blade, remove the
blade guard assembly (D) and throat
plate (X) prior to installing the new
blade. (Refer to sharpen your new saw is 2.2 mm thick. Place the blade (C) on the riving knife. Ensure that you locate a reputable sharpening service...
Instruction Manual - Page 11
... power source before installing and removing accessories, before adjusting or changing setups or when making repairs. The blade guard assembly is properly attached and the anti-kickback assembly is a dangerous condition! ALWAYS make sure both guards are in the down position in contact with the table before operating. WARNING: Before connecting the table saw blade.
8.
Measure the...
Instruction Manual - Page 12
...and it falls off the rear of the table. When a small
U
width is to be ripped and the
hand cannot be used for this manual to make
push sticks. Refer to obtain ...
first two fingers and near the fence.
5.
NOTE: The table saw , attached to the rip fence. Continue pushing the workpiece until the cut off side of the workpiece. The work
support must
not be used in starting ...
Instruction Manual - Page 13
... set to the power source or operating the saw,...table saw blade. English
Push Block (Fig. 36, 37)
IMPORTANT: Only use a length stop on the free end of the workpiece when crosscutting.
Mitering
WARNING: Miter angles greater FIG. 40 than 0°.
CAUTION: Certain workpiece shapes, such as a guide or length stop when crosscutting.
Refer to Narrow Rip Auxiliary Fence...
Instruction Manual - Page 14
... leading edge of the featherboard will support the workpiece until the cut is...fence. 2. Remove blade guard assembly (D). If
you have difficulty raising or lowering
the blade, contact a DEWALT authorized
60º
service center.
English
Miter Gauge Operation
Dust Collection
FIG. 43
To set your miter gauge, loosen the lock handle and move the miter gauge to the desired Your table saw...
Instruction Manual - Page 15
....
90 DAY MONEY BACK GUARANTEE If you are covered by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any reason, you for three years from power source before installing and removing accessories, before adjusting or changing setups or when making repairs. never immerse any part of your DEWALT Power Tool, Laser, or Nailer for any defects due to...
Instruction Manual - Page 52
...DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
(APR13)
Part No. N273727 DWE7480 Copyright © 2013 DEWALT
The following are trademarks for one or more DEWALT...stick so hand will clear blade guard and rip fence. Ajuste el largo de las varas de empuje para...dégagée du protège-lame et du guide longitudinal. CAUTION: Make push stick from slipping. Muesca para ...
Parts Diagram - Page 8
... 292
Part Number
...Parts List for current parts information. Parts list, pricing, and availability subject to change. Page 6 Please visit www.dewaltservicenet.com for DWE7480 Type 1
Description
Qty Required
DEWALT LABEL
1
SCALE LABEL
1
LABEL
1
WARNING LABEL
1
FENCE ASSEMBLY
1
PLATE
2
DOWEL PIN
2
SPRING PLATE
2
THROAT PLTE ASM
1
SCREW
4
SCREW
1
CAM
1
SPRING
1
SET...
Dewalt DWE7480 Reviews
We have not received any reviews for Dewalt yet.