Dewalt D28140 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28140 manuals!
Problems with Dewalt D28140?
Ask a Question
Free Dewalt D28140 manuals!
Problems with Dewalt D28140?
Ask a Question
Popular Dewalt D28140 Manual Pages
Instruction Manual - Page 3
...OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). Read all safety warnings and all instructions.
d) Do not abuse the...to these symbols. Keep cord away from heat, oil, sharp edges or moving parts. Use of a cord suitable for carrying, pulling or unplugging the power tool.... instruction manual.
General Power Tool Safety Warnings
WARNING!
Instruction Manual - Page 5
... the accessory such as a grinder, sander, wire brush, polisher or cut-off tool. e) The arbor size of operation.
Read all instructions listed below may fly away and...not use accessories which are not specifically designed and recommended by a qualified repair person using only identical replacement parts. After inspecting and installing an accessory, position yourself and bystanders...
Instruction Manual - Page 8
...wiring or piping. Additional Safety Rules for Grinders
WARNING: The grinding wheel or accessory ...resulting in this tool for Cord Sets
Ampere Rating
Volts
Total Length of...another practical way to secure and support the workpiece to maintain control of...greater the capacity of Cord in moving parts and should always be avoided. If in... Do not operate this manual is 16 gauge has more than 18 gauge...
Instruction Manual - Page 10
... or any part of flammable liquids or gases. Stamped Steel Quick-Change
D28144, D28144N
Backing Flange (depressed
B. DO NOT use this tool.
8 Yellow Rubber Ring
H. Lock-Off Lever
center wheels only):
C. These heavy-duty angle grinders are professional power tools. Anti-Vibration Side Handle I1. Dust Ejection System™ (DES)
(Type 1): D28140,
L. Paddle Switch...
Instruction Manual - Page 11
...housing become separated by a DEWALT service center. Overtightening could cause ...D28140, D28144, D28144N) The torque limiting clutch reduces the maximum reaction torque transmitted to the motor will return to normal once the tool has cooled down to strip.
5. The torque limiting clutch has been factory set...installing and removing accessories, before adjusting or when making repairs. Re-install...
Instruction Manual - Page 12
...over rated accessory speed may have been designed for information on pages 10-12 of this manual. Every unthreaded accessory must have a 7/8" (22.2 mm) arbor hole. Threaded accessories must... the correct accessories. See pages 10-12 for a circular saw and should not be above listed minimum wheel speed as shown on the tool warning label. If it does not, it may... grinder accessories.
Instruction Manual - Page 14
...-adjusted to secure the guard on the gear case hub.
3. Mounting instructions for use with a loose guard or the clamp lever in the accessory.... With the guard latch open, rotate the guard (I
M
2. Some DEWALT models are aligned and pull up on the gear case. FIG. 3 N
...in the groove on the gear case. Do not operate the grinder with sanding flap discs
O
I ) into the desired working ...
Instruction Manual - Page 15
...and release the trigger switch to repair or replace the guard. An accidental start ... take the tool and guard to a service center to ensure that the switch
is... label. Lift the tool from power source before installing and removing accessories, before touching the work surface....use with the grinder accessories. Depress and release the paddle switch as described above listed minimum wheel speed...
Instruction Manual - Page 16
...the work surface. SLIDER SWITCH (FIG. 6)
D28131, D28140
CAUTION: Before connecting the tool to a power supply,...spindle lock (C) is in extended use a wrench to the grinder by an O-ring on button (J) offers increased FIG. ...releasing. Lift the tool from rotating when installing or C removing wheels. Backing flange is... backing flange by pressing the rear part of the wheel. 4. Thread the...
Instruction Manual - Page 18
... when the tool operates at high speed.
3. Remove the tool from your local dealer or authorized service center.
1. Place the sanding disc (S) on page 11 for side pressures encountered with a standard ...off work surface.
2.
The open -underside of these wheels are complete.
1. Changing the angle will cause the wheel to
avoid creating gouges in depth]. WARNING: Do not use of...
Instruction Manual - Page 19
... while
turning the sanding disc until the sanding
disc and clamp nut are snug.
5. Maintain a 5˚ to 15˚ angle between the tool and work surface before turning the tool on the grinder spindle without moving, or moving the tool in various grits.
English
3. Move
to fragment from work surface. Coarse grits...
Instruction Manual - Page 20
... rotating before setting it down until the guard lug engages and rotates freely in a forward and FIG. 17 backward motion to 10˚ angle between the edge of grinder may be experienced...the work surface.
2. NOTE: All grinders that use Type 1 wheels use are available. WARNING: A closed, 2-sided cutting wheel guard is not included with this tool (D28140, D28144, D28144N ONLY) and is greatest...
Instruction Manual - Page 21
...setting it from the wheel.
4. Install the threaded clamp nut with the raised section (pilot) facing away from power source before installing and removing accessories, before adjusting or when making repairs.... Place the wheel on the quick-change the angle of the cut is begun and a notch is... used for cutting wheels.
1. Do not operate
grinder with the clamp lever in open position. Close ...
Instruction Manual - Page 22
...repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258) or visit our website: www.
Recommended accessories for three years from your tool are covered by our:
1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by DEWALT...This warranty gives you specific legal rights and you obtain more efficient warranty service in case there is ...
Instruction Manual - Page 76
... Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT12) Part No. N234379 D28114, D28114N, D28131, D28140, D28144, D28144N Copyright © 2006, 2007, 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the...
Dewalt D28140 Reviews
We have not received any reviews for Dewalt yet.