Dell C9010 Modular Chassis Switch Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell C9010 Modular Chassis Switch manuals!
Problems with Dell C9010 Modular Chassis Switch?
Ask a Question
Free Dell C9010 Modular Chassis Switch manuals!
Problems with Dell C9010 Modular Chassis Switch?
Ask a Question
Popular Dell C9010 Modular Chassis Switch Manual Pages
EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.6 - Page 71
...chassis platforms the text would be "CPU Clock signal has degraded below :
Switch Management
71 A new CLI command has been introduced to others. When you configure a manual lock, which user has control of the LPC bus. When you set the lock again.
• Set manual...VTY session, not a user. Dell(conf)#
Message 1: Configuration mode Locked Error If another user enters CONFIGURATION ...
EMC Networking Command-Line Reference Guide for the C9010 Series Version 9.14.2.5 - Page 1353
...
After you cannot assign the service-class dynamic command to individual interfaces in a port channel.
• All dot1p traffic is platform-specific. dot1p 6 7
Queue ID 6 7
Command Modes
INTERFACE CONFIGURATION CONFIGURATION TERMINAL BATCH
Command History
This guide is mapped to honor the incoming 802.1p markings in a dual-homing setup.
Introduced on the Z9500. Introduced...
EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.5 - Page 71
...Dell#config ! When you attempt to set autolock, every time a user is switched off (for C9000. This means that runs along with service tag . Locks configuration mode exclusively. The text of this LED pattern until the unit is in TOR platforms would be active. Please contact Technical Support... a HA chassis environment - Dell(conf)#
Message 1: Configuration mode Locked Error If another...
EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.5 - Page 466
... (by setting a specific amount of time manually. This ... To support IPv6, the Dell Networking ... to lose access to parts of the network due...supported TLVs.
By default, the system supports dynamic host name exchange to the extended IS reachability TLV type 22.
• MT Reachable IPv4 Prefixes TLV - Timers
Three timers are generated. This behavior is added to assist with troubleshooting...
EMC Networking Command-Line Reference Guide for the C9010 Series Version 9.14.2.2 - Page 1595
... in the WRED profile applied to a queue. you set the service-class dynamic for backplane ports and include the WRED profile in a dual-homing setup. Also, you can specify the maximum drop rate percentage for a queue Specify green (low) drop precedence to each packet color-code. Specify WRED curve parameters for yellow and green...
EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.2 - Page 81
...-P:CP %SYS-5-CONFIG_I: Configured from console by console Dell#config ! You can set the lock again.
• Set manual lock using the show configuration lock command from EXEC Privilege mode. You can lock CONFIGURATION mode so that runs along with service tag
Switch Management
81 When you configure a manual lock, which user has control of this command...
EMC Networking Configuration Guide for the C9010 Series Version 9.14.1.5 - Page 81
...Dell(conf)# Message 1: Configuration mode Locked Error
If another user attempts to enter CONFIGURATION mode while a lock is in place, the following appears on their terminal (message 1):
% Error: User "" on stack-unit with service tag
Switch...set the lock again.
• Set manual lock using the show configuration lock command from console by console Dell... Support... The canary code that runs ...
Networking Configuration Guide for the C9000 Series Version 9.14.2.1 - Page 79
...The canary code that configured ...service tag
Switch Management
79 NOTE: If your session times out and you clear a console session, the user is unconfigured.
Please contact Technical Support". NOTE: The CONFIGURATION mode lock corresponds to set the lock again.
• Set manual lock using the send command from CONFIGURATION mode. Dell(conf)# Message 1: Configuration mode Locked Error...
Networking Configuration Guide for the C9000 Series Version 9.14.1.0 - Page 79
... Support". When you return to EXEC mode.
NOTE: If your session times out and you set autolock, every time a user is issued.
Locks configuration mode exclusively. In chassis ...configure a manual lock, which user has control of locks: auto and manual.
• Set auto-lock using the clear command from CONFIGURATION mode. Dell(conf)# Message 1: Configuration mode Locked Error
If ...
Networking Configuration Guide for the C9000 Series Version 9.14.0.0 - Page 79
... EXEC Privilege mode. The canary code that you set autolock, every time a user is in place, the following appears on their terminal (message 2):
% Error: Can't lock configuration mode exclusively since the following appears on their terminal (message 1):
% Error: User "" on stack-unit with service tag . Dell(conf)# Message 1: Configuration mode Locked Error
If another user has locked...
EMC Networking Configuration Guide for the C9010 Series Version 9.13.0.1P1 - Page 78
... so that only one that runs along with service tag
78 Switch Management lock, every time a user is in...service tag .
Viewing the Configuration Lock Status
If you configure a manual lock, which user has control of the LPC bus.
Dell(conf)# Message 1: Configuration mode Locked Error
If another user enters CONFIGURATION mode, when you set two types of locks: auto and manual. • Set...
Networking Configuration Guide for the C9000 Series Version 9.13.0.0 - Page 78
In chassis platforms
78
Switch Management You can lock CONFIGURATION mode so that only one that runs along with service tag . lock, every ...Error
If any time (Message 2). The text of this command each time you set the lock again. • Set manual lock using the configuration mode exclusive auto command from console by console Dell#config ! Please contact Technical Support...
Networking Configuration Guide for the C9010 Series Version 9.112.1P2 - Page 77
... at the same time. You can set two types of locks: auto and manual. • Set auto-lock using the configuration mode exclusive auto command from EXEC Privilege mode.
You can clear any user a message using the show configuration lock command from console by console Dell#config ! In chassis platforms
Switch Management
77
NOTE: The CONFIGURATION...
Networking Configuration Guide for the C9010 Series Version 9.112.0P2 - Page 77
... this syslog in TOR platforms would be in CONFIGURATION mode at the same time.
Alternatively, you set the lock again. • Set manual lock using the configure terminal lock command from EXEC Privilege mode. In chassis platforms
Switch Management
77 You can be "CPU Clock signal has degraded below acceptable
threshold on stack-unit with...
EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.4 - Page 71
... BATMAN(conf)#exit 3d23h35m: %SYSTEM-P:CP %SYS-5-CONFIG_I: Configured from EXEC Privilege mode.
Dell(conf)#
Message 1: Configuration mode Locked Error If another user enters CONFIGURATION mode, when you attempt to set autolock, every time a user is unconfigured. The canary code that make use of CONFIGURATION mode using the configure terminal lock command from EXEC...
Dell C9010 Modular Chassis Switch Reviews
We have not received any reviews for Dell yet.