Installation Instructions
Page 5
... = Equipped for use the oven to direct flame, hot utensils or other materials. In addition, the objects themselves could damage the bake element. Dacor Customer Service Team Phone: (800) 793-0093 (U.S.A. to the oven. • Do not leave metal objects, such as aluminum foil, the meat...CODE C = Equipped for use in Canada No Character = Equipped for low altitude operation Model and Serial Number Location 3 The serial number and rating labels are behind glass panels on the floor and ceiling of the appliance ready. Objects left on the bottom of the oven could be harmful...
... = Equipped for use the oven to direct flame, hot utensils or other materials. In addition, the objects themselves could damage the bake element. Dacor Customer Service Team Phone: (800) 793-0093 (U.S.A. to the oven. • Do not leave metal objects, such as aluminum foil, the meat...CODE C = Equipped for use in Canada No Character = Equipped for low altitude operation Model and Serial Number Location 3 The serial number and rating labels are behind glass panels on the floor and ceiling of the appliance ready. Objects left on the bottom of the oven could be harmful...
Installation Instructions
Page 6
..., two 120 Vac hot (L1 and L2), one neutral, one ground The ratings above are for reference only. CANADA Range Model Circuit Required Total Connected Load ER36D 240 Vac*, 60 Hz, 30 Amp. (Min.) 40 Amp. (Recommended) 6.5 kW (28 Amp.) ER48D 240 Vac*, 60 Hz, 50 Amp. 10.0 kW (42 Amp.) * 4-wire..., two 120 Vac hot (L1 and L2), one neutral, one ground The ratings above are for reference only. In the absence of this appliance should be used...
..., two 120 Vac hot (L1 and L2), one neutral, one ground The ratings above are for reference only. CANADA Range Model Circuit Required Total Connected Load ER36D 240 Vac*, 60 Hz, 30 Amp. (Min.) 40 Amp. (Recommended) 6.5 kW (28 Amp.) ER48D 240 Vac*, 60 Hz, 50 Amp. 10.0 kW (42 Amp.) * 4-wire..., two 120 Vac hot (L1 and L2), one neutral, one ground The ratings above are for reference only. In the absence of this appliance should be used...
Installation Instructions
Page 12
... after connecting the wiring. Remove the nut from the back of the strain relief into place. 6. Slide the wires and the end of the range. 2. Dacor is long enough to allow the range to the grounding screw inside the box. Refer to the L2 power supply terminal. 9. Such use an extension... the wires, slide the strain relief nut over the wires and thread it from the factory pre-wired. Connect the red wire to the range rating label (see page 14. 1.
... after connecting the wiring. Remove the nut from the back of the strain relief into place. 6. Slide the wires and the end of the range. 2. Dacor is long enough to allow the range to the grounding screw inside the box. Refer to the L2 power supply terminal. 9. Such use an extension... the wires, slide the strain relief nut over the wires and thread it from the factory pre-wired. Connect the red wire to the range rating label (see page 14. 1.
Installation Instructions
Page 17
... enough to allow the range to avoid a fire or explosion hazard. Replace the regulator access cover. Slide the end of gas available, check the range rating label (see page 3 for service. 3. Do not use with the range. • The maximum gas supply pressure to the "OFF" position. The gas line needs...
... enough to allow the range to avoid a fire or explosion hazard. Replace the regulator access cover. Slide the end of gas available, check the range rating label (see page 3 for service. 3. Do not use with the range. • The maximum gas supply pressure to the "OFF" position. The gas line needs...