D-Link DCH-Z120 Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DCH-Z120 manuals!
Problems with D-Link DCH-Z120?
Ask a Question
Free D-Link DCH-Z120 manuals!
Problems with D-Link DCH-Z120?
Ask a Question
D-Link DCH-Z120 Videos
D-Link DCH-Z120: mydlink Home Battery Motion Sensor
Duration: 2:54
Total Views: 2,734
Duration: 2:54
Total Views: 2,734
D-Link DCH-Z120 Alertas Push por deteccion de movimiento
Duration: :51
Total Views: 951
Duration: :51
Total Views: 951
Como resetear el D-Link DCH-Z120 y volver a configurarlo con la base
Duration: 2:01
Total Views: 2,178
Duration: 2:01
Total Views: 2,178
D-Link DCH-Z120 Recepcion de notificaciones Push
Duration: 1:13
Total Views: 490
Duration: 1:13
Total Views: 490
Popular D-Link DCH-Z120 Manual Pages
User Guide - Page 1
.... Add to remotely control applications in the add mode. DCH-Z110/Z120
The device adopt the Z-WaveTM 500 series chip, when your Z-WaveTM network system is in residential and light commercial environments. And it supports the security, OTA... The network system will act as lighting, home access control, entertainment systems and household appliances.
First...
User Guide - Page 2
...trigger event and also report the battery status, temperature and illumination level. The group 2 is 120 hours. When it wake-up 10 seconds. If the user want to add it can ... support 8 nodes maximum. •Failed or success in default. Notice 1: Always RESET a Z-WaveTM device before trying to wake-up interval minimum setting is 30 minutes, and maximum setting is for receive the setting ...
User Guide - Page 3
... over 5 seconds. And if the temperature is enabled, to disable this function by setting the configuration N0.5 bit4 to the nodes in the group 1.
* Temperature Report: When... Type: Tamper (0x08) Sensor Value: 0xFF
Notification Report (V4) Notification Type: Home Security (0x07) Event: Motion Detection, Unknown Location (0x08) Sensor Binary Report (V2) Sensor Type: Motion (0x0C) Sensor Value:...
User Guide - Page 4
... also support the timing unsolicited report of the
Caution 1: Enable this duration, the controller can presses the tamper key 3 times to abort the NWI mode.
•Low battery report: When the battery level is setting the differential value too small, it will cause the PIR Motion to
every 2 seconds.
Let the controller into the firmware update...
User Guide - Page 5
...setting of the configuration NO. 8. When the event triggered, normally the LED won't indicated, unless the battery is for the normal operation. At that the user...for the user test the sensor function when installation.
And ...firmware broken, and the device will start flash in the group 2. The device supports the security function. The messages also include the battery level, the
5
User Guide - Page 7
... DCH-Z120. 2.Don't let the device facing the window or the sunlight. 3.Don't let the device facing the source of heat.
For instance the heater or the air-condition. 7 The user should replace the battery to 1-1, and press down. Replace the new battery and install the cover back. 1.Put the front cover bottom to new one. Choosing a Suitable Location...
User Guide - Page 8
...thinner (hereinafter referred to as B tape), you can use A tape for A tape installation is good or not by using tape B. In the accessory pack. There are two types... normal mode. Unless the user execute the "RESET" procedure. * The reserve bit or not supported bit is 1. * The configuration mark with star(*), means after the remove the setting still keep, don't reset to fix, then you can...
User Guide - Page 9
...Valid A B
Description Valid A B
Description
Setting the BASIC command value to 99 will enable the illumination detected function and update the illumination value. High sensitivity means can ...test mode. (1:Disable,
0:Enable)
NO. The 0xFF(-1) means
2
Basic Set Level
0xFF
All
turn on the light.
0 means turn on
the light.
Name Def.
Bit1:...
User Guide - Page 10
...the lighting in auto report. (1:Disable, 0:Enable)
0
Bit6: Disable to report battery state
when the device triggered. (1:Disable,
10
Bit1: Enable sending motion OFF
report. (0:Disable, 1:...1
to control. Notice: If this bit is 1, it is
recommended also set the Bit1 to turn ON the lighting nodes in that room. Valid A B
Description
4 All
Customer...
User Guide - Page 11
...function. Auto
10
Report Battery
Time
The interval time for auto report the
12
0 ~
127
battery level. 0 means turn off auto report battery.
The tick time
can setting by the configuration No....turn off auto report
127
illumination. The tick time
can save the battery
energy.
Also can setting by the configuration No.20.
11 Auto Report...
User Guide - Page 12
... COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_MULTI_CMD COMMAND_CLASS_SECURITY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MARK COMMAND_CLASS_BASIC
Specifications
Power by CR123A lithium battery. Valid A B Def. NO. Enable this function. FCC ID for DCH-Z110: KA2CHZ110A1 FCC ID for DCH-z120: KA2CHZ120A1
12 Signal (Frequency):
868.40 MHz...
User Guide - Page 13
...
and can radiate radio frequency energy and, if not installed and used in a particular installation.
However, there is subject to Part 15 of the FCC Rules. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
radio communications. If this equipment. Warning
Do...
D-Link DCH-Z120 Reviews
We have not received any reviews for D-Link yet.