D-Link 809TC - Hub - EN Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link 809TC manuals!
Problems with D-Link 809TC?
Ask a Question
Free D-Link 809TC manuals!
Problems with D-Link 809TC?
Ask a Question
Popular D-Link 809TC Manual Pages
User Guide - Page 11
10BASE-T Ethernet Mini Hubs User's Guide
1 Introduction
This User's Guide tells you how to install the following 10BASE-T Ethernet Mini Hub models: ♦ DE-809TP (9 UTP ports) ♦ DE-809TC (8 UTP ports & 1 BNC port)
Port connectors on back panel of Mini Hubs
Introduction
1
User Guide - Page 12
...or fewer nodes. Model DE-809TC provides eight UTP ports (eight RJ-45 connectors) and one of a larger network.
♦ Installation flexibility.
Each Mini Hub provides nine ports. The DE-809TC provides a BNC port... ports or more.
♦ Compact, lightweight. Through an "Uplink" switch, a UTP port of the DE-809TP can be part of these ports can be easily mounted on a desktop, and its light...
User Guide - Page 17
10BASE-T Ethernet Mini Hubs User's Guide
2 Installation
Mounting Hub on Wall
The Mini Hub can be mounted on the bottom side of the hub for this purpose. Four mounting slots are provided on a wall. Make sure that the front panel is exposed to allow you to view the LEDs at work.
Installation
5
User Guide - Page 19
10BASE-T Ethernet Mini Hubs User's Guide
Connecting AC Power Adapter
The Mini Hub uses an external AC power adapter. There is connected to an AC power source and the hub's...FRXQWU\ LV QRW OLVWHG LQ WKH DSSHQGL[ñ FKHFN ZLWK \RXU QHWZRUNLQJ SURGXFWV GHDOHU WR PDNH VXUH WKDW \RX XVH D SURSHU $& SRZHU DGDSWHUï
Installation
7 The hub is powered on once the AC power adapter is no power...
User Guide - Page 21
10BASE-T Ethernet Mini Hubs User's Guide
Note that, for Mini Hub model DE-809TP, UTP port labeled "9" must be in the Uplink position (see section Cascading Hubs Through UTP ... a station, bridge or router. The button to the right of a 10BASE-T hub, the port must be connectable to switch between the Normal and the Uplink position.
Installation
9
To connect this chapter for details).
User Guide - Page 22
Connecting Thin Coaxial Segment
The BNC port on Mini Hub model DE-809TC is used to connect to the thin coaxial cable. Connect a T-connector to the BNC connector, then connect both ends of the T-connector.
10
Installation If the thin coaxial segment terminates at the hub, attach a 50-ohm terminator to one end of the T-connector to a thin coaxial segment.
User Guide - Page 23
10BASE-T Ethernet Mini Hubs User's Guide
Cascading Hubs Through Thin Coaxial Cable
The BNC port on the Mini Hub model DE-809TC can be used to cascade a maximum of cable between two BNC ports. In this sense, it is possible to cascade hubs together. Installation
11
You may cascade DE-809TC hubs together through the thin coaxial...
User Guide - Page 24
... when two UTP ports of two hubs are reversed. If you use Mini Hub model DE-809TP, UTP port labeled "9" is in the Uplink position can be crossed over... be used by pressing down the button located next to dispense with the trouble of crossing the UTP cable's wires. When this might
cause unpredictable results.
12
Installation Note: Never cause a loop when you to the port. Mark all ...
User Guide - Page 27
...Installation
15 Check for a "power good" condition at both ends of Mini Hubs
♦ Collision. ◊ Blinking: Packet collision is successful. ◊ OFF: (1) No data link or (2) cable disconnected.
The computers should then back off, then retry transmission. 10BASE-T Ethernet Mini Hubs User's Guide
DE-809TC....
♦ Link/Rx (for service. ◊ Blinking: Packet reception is ...
User Guide - Page 28
.... If segment is not terminated, terminate both ends with 50-ohm terminators. ◊ OFF: (1) Cable is connected and (2) segment has no problem.
♦ Partition (for each UTP port). ◊ ON: The UTP port is in the Normal position (straight-through wires (no cross-... that the UTP cable between a hub port and a non-repeater node must contain straight-through wires).
16
Installation
User Guide - Page 29
10BASE-T Ethernet Mini Hubs User's Guide
A
Cables, Connectors & AC Power Adapters
10BASE-T Unshielded Twisted-Pair (UTP) Cable
♦ Cable characteristics: 0.4 - 0.6 mm (22 - 26 AWG) 8-wire (only 4 wires used for 10BASE-T)
♦ ...
User Guide - Page 30
... complies with the output power listed below and the input power and plug (AC power specifications) of the AC power adapters supplied by D-Link for use with the Mini Hub. standard ⇒ Safety standard: BSI
AC power adapter model AD-071AB ⇒ Input power: AC 220 volts, 50-60Hz ⇒ Output power: DC...
User Guide - Page 31
10BASE-T Ethernet Mini Hubs User's Guide
⇒ Plug: German standard ⇒ Safety standard: VDE
AC Power adapter model AD-071AJ ⇒ Input power: AC 100 volts, 50-60Hz ⇒ Output power: DC 7.5 volts unregulated, 1 A ⇒ Maximum power consumption: 7.5 watts ⇒ Safety standard: Japan T-mark
Cables, Connectors & AC Power Adapters
19
User Guide - Page 32
B
Technical Specifications
DE-809TP
♦ Standard: IEEE 802.3 10BASE-T. ♦ Medium support: UTP. ♦ Number of UTP ports: 9. ♦ Number of connectors: 9 RJ-45. ♦ Cascading: Switchable straight-through/cross-wired UTP port
... Weight: 300 ±10 grams (AC power adapter excluded) ♦ Safety: UL/CSA. ♦ EMI: FCC-B, CE-B, VCCI-A, C-Tick, BCIQ
20
Technical Specifications
User Guide - Page 36
...Link LANsmart †Novell NetWare †NetWare Lite †SCO Unix/Xenix †PC NFS †3Com 3+Open †Banyan Vines †DECnet Pathwork †Windows NT †Windows NTAS †Windows '95 †Other
5. Your name: Mr./Ms Organization Dept Your title at installation...address... address
Answers...Link product to support your organization use ? †XNS/IPX †TCP...
D-Link 809TC Reviews
We have not received any reviews for D-Link yet.