Cisco RSP2 - Route Switch Processor 2 Support and Manuals
Cisco RSP2 Videos
Popular Cisco RSP2 Manual Pages
Installation Guide - Page 20
... of main memory
[additional displayed text omitted from this example]
Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-JV), Version 11.1(4) [biff 51096]
20
OL-4923-01 B0 Compiled Mon 22-Jan-96 21:15 by biff Image text-base: 0x600108A0, data-base: 0x607B8000
cisco RSP2 (R4600) processor with more DRAM. (See the "Verifying System Startup...
Installation Guide - Page 21
... Kbytes of main memory
[additional displayed text omitted from this example]
Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-JV), Version 11.1(4) [biff 51096] Copyright (c) 1986-1996 by biff Image text-base: 0x600108A0, data-base: 0x607B8000
cisco RSP2 (R4600) processor with 16384K bytes of your router.)
OL-4923-01 B0
21 Compiled Mon 22-Jan-96 21...
Installation Guide - Page 24
... all functions of the active-mode software.
• When enabled, automatic synchronization mode automatically ensures that occupies the first even RSP slot on the Cisco 7505 or the Cisco 7576 routers. In the following routers: Cisco 7507, and Cisco 7513. HSA is not supported on the router is the active (normally the RSP4/4+ if the RSP2 is used in conjunction with...
Installation Guide - Page 25
... HSA operation with one RSP2 and one RSP standby
processor card, and the proper Cisco IOS release (refer to automatically synchronize configuration information on both implementations)
OL-4923-01 B0
25 The RSP2 cannot be turned off or on per card)
Note Other, more information, contact your Cisco service representative.
otherwise, use HSA for software error protection? The third...
Installation Guide - Page 26
... Startup Images for the Active and the Standby RSPs, page 30 (software error
protection only) • Manually Setting Environment Variables on the Standby RSP, page 37 (both implementations) • Automatically Setting Environment Variables on a Cisco 7507:
Router# configure terminal Router (config)# slave default-slot 2 Ctrl-Z Router# copy running -config nvram:startup-config Saves this...
Installation Guide - Page 29
... EXEC mode:
Table 7 Confirming That Both RSPs Have the Same Microcode Images
Step Step 1
Step 2 Step 3 Step 4
Command
Description
Router# show controller cbus MEMD at 40000000, 2097152 bytes (...standby RSP2 has a copy of the active RSP supplementary microcode.
Thus, you perform the squeeze command. slot1: FIP, hw 2.9, sw 20.02, ccb 5800FF40, cmdq 48000088, vps 4096
software loaded...
Installation Guide - Page 38
... a Fast Software Upgrade, page 56 - To do so, perform the following topics: • High Availability Features, page 39 • Hardware and Software Prerequisites, page 40 • Installation Procedures, page... standby RSP taking control of the router when the active fails, rendering the network inoperable.
Configuring SLCR, page 59 • RPR, RPR+, SSO, and FSU Troubleshooting Tips...
Installation Guide - Page 40
Cisco 7500 Series Routers feature module, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120limit/120s/120s22 /nsf120s.htm. Fast Software Upgrade permits users to upgrade to an interim release or next minor release Cisco IOS image by Cisco Express Forwarding (CEF) for the standby RSP to learn and converge routes. Once the routing protocols have ...
Installation Guide - Page 44
... 6 Step 7 Step 8
Router(config-red)# exit Router(config)# end Router# hw-module sec-cpu reset
Purpose
Enters configuration mode.
The system then operates in Step 2, this command loads and executes the bundled default IOS standby image. If a high availability image is found , the running configuration is updated.
• slot-number-Specifies the standby RSP slot where the...
Installation Guide - Page 45
...-cache distributed no service password-encryption service single-slot-reload-enable ! OL-4923-01 B0
45 Reason for last switchover:User forced. Configuring RPR and RPR+ Example
In the following example, the active RSP is in slot 3 of a Cisco 7507 router. hostname Router1 ! hw-module slot 2 image slot0:rsp-pv-mz hw-module slot 3 image slot0:rsp-pv-mz ip...
Installation Guide - Page 48
... protocols or applications. Router# show redundancy states my state = 13 -ACTIVE peer state = 8 -STANDBY HOT Mode = Duplex Unit ID = 7
Redundancy Mode = sso Maintenance Mode = Disabled Manual Swact = Enabled Communications = Up
client count = 12 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0
Enter the show redundancy command to display the list of supported line protocols.
Installation Guide - Page 58
...hw-module slot 2 image slot0:rsp-pv-mz Router(config)# hw-module slot 3 image slot0:rsp-pv-mz Router(config)# end Router# hw-module sec-cpu reset Router# copy running -config startup-config
Saves the configuration changes to troubleshoot the RPR, RPR+, and FSU features on Cisco 7500 series routers:
Command
Router# show diag Router# show redundancy
Router# show a Fast Software Upgrade performed...
Installation Guide - Page 67
... Echos to the software release installed on your system administrator to a remote server before removing the RSP2, you replace the RSP2 in NVRAM on page 22 and contact your Cisco hardware.
See the "Using the EXEC Command Interpreter" section on the RSP2.
For configuration information and support, refer to the Cisco IOS software configuration documentation set that the connection...
Installation Guide - Page 74
... and then at the same angle and the same height when properly installed. Routers with Cisco Systems memory kits. Step 3 Insert the connector edge of the correct size and speed or the system cannot operate. If you damage a socket, you would verify the memory upgrade.
• Observe the LED states and the console display.
Installation Guide - Page 81
... you set the boot field value to 0, you must boot the operating system manually by that value. End with the name cisco and adds the octal equivalent of the router:
Router# configure terminal Enter configuration commands, one per line.
Table 20 Default Boot Filenames
Action/Filename Bootstrap mode Default software cisco2-RSP cisco3-RSP cisco4-RSP cisco5-RSP cisco6-RSP
Bit...
Cisco RSP2 Reviews
Do you have an experience with the Cisco RSP2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!