Cisco ESW-520-48-K9 Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco ESW-520-48-K9 manuals!
Problems with Cisco ESW-520-48-K9?
Ask a Question
Free Cisco ESW-520-48-K9 manuals!
Problems with Cisco ESW-520-48-K9?
Ask a Question
Popular Cisco ESW-520-48-K9 Manual Pages
User Guide - Page 12
..., and the procedures so that you can decide how to display the device manager interface through a secured mode. Use this way:
Chapters Introduction Setup and Installation
Customization Monitoring Troubleshooting Reference Cisco Support Resources
Purpose
This chapter describes the software and hardware features and benefits so that you can set up the switch for the first time and...
User Guide - Page 19
... rack, or mounted on page 2-5. events detected - setup mode
SETUP button
SYSTEM ALERT PoE SETUP
OL-8122-01
User Guide for the Catalyst Express 500 Switches
1-5 For hardware installation information, see the "Install the Switch" section on a wall.
PoE status - Figure 1-2
Catalyst Express 500 Hardware Overview
AC power connector
Port LEDs
Security cable slot side and rear panels...
User Guide - Page 21
... Guide for data being
received and sent on page 1-12. Express Setup • Initial setup only requires IP information for first-time switch configuration. • Quick IP information updates if you relocate the switch to resolve each problem. • Graphical front panel display, LEDs, gauges, graphs, and animated indicators show switch and port
status, utilization, and error percentages...
User Guide - Page 22
... graphical device management tool for the Catalyst Express 500 Switches
1-8
OL-8122-01 It uses graphical, color-coded displays such as Express Setup and Smartports for quickly setting up to their attached devices. Features and Benefits
Chapter 1 Introduction
Customization
• Smartports port roles optimize switch ports according to 32 VLANs. Internet Group Management Protocol (IGMP...
User Guide - Page 25
... for Internet Explorer 5.5. Service Pack 1 or higher is supported. Table 1-2
Hardware Requirements
Processor Speed Intel Pentium II1
DRAM 64 MB2
1. The device manager verifies the browser version when starting a session to manage the switch: • Cisco Network Assistant, page 1-12 • Simple Network Management Protocol, page 1-13
OL-8122-01
User Guide for the Catalyst...
User Guide - Page 32
... to the Switch" section on the device manager. Set Up the Switch for the First Time
Chapter 2 Setup and Installation
Default Gateway Username Password
The IP address for the Catalyst Express 500 Switches
2-4
OL-... gateway cannot be part of your devices are in this window, choose Configure > Users and Passwords from the device manager menu. The password for the switch can have up ...
User Guide - Page 51
... as well as the same priority given to troubleshoot network problems. The settings on a switch port should be compatible with the port settings of the connected device. All traffic from this window, choose Configure > Port Settings from the device manager menu. Update Basic Port Settings
The basic port settings determine how data is Cisco CallManager.
An example of a critical server is...
User Guide - Page 53
...could guess the password.
OL-8122-01
User Guide for additional guidelines and procedures. To display the Users and Passwords window, choose Configure > Users and Passwords from the Users and Passwords window (Figure 3-5).
Note This setting is available only on PoE ports. After initial setup, you must enter both a username and password. If you no longer want a specific username, you...
User Guide - Page 56
... Cisco-Voice VLAN, a special VLAN supported on the switches.
The default VLAN is given to voice traffic over regular IP data traffic. During initial setup,...specific switch ports.
• Cisco-Guest VLAN offers Internet-only access to three types of the default VLAN.
3-14
User Guide for the Catalyst Express 500 Switches
OL-8122-01
Voice traffic from the phone and IP phone service...
User Guide - Page 58
... assigned to the Cisco-Guest VLAN. You can modify the name of your network requires segregating either or both voice and guest traffic and if you create additional VLANs, you must also create VLANs specifically for the Catalyst Express 500 Switches
OL-8122-01 Only ports with the IP Phone+Desktop port role can be...
User Guide - Page 79
...-8122-01
User Guide for this switch.
Used together, you upgrade the switch software.
This information cannot be changed . For information about the switch:
Name
Product ID IP Address
MAC Address Version ID Serial Number Software
Contact
Location
The name of this switch. The model of this switch. This information cannot be modified. The Cisco IOS software version that...
User Guide - Page 99
... file. OL-8122-01
Use the Software Upgrade window (Figure 5-3) to delete the current configuration settings, and then restart the switch. The same software image is retained. Chapter 5 Troubleshooting
Restore Switch Settings
• Reset the switch to update the switch with the latest software changes (such as described in the Getting Started Guide for the Catalyst Express 500...
User Guide - Page 102
... blinks green. Note If the Setup LED is amber, there is no available switch port to which to connect your management station directly to the switch port with a blinking green port LED. Press the SETUP button until the Setup LED and the port LED blink green.
3. Connect your management station.
Recover a Password
Chapter 5 Troubleshooting
Recover a Password
Prerequisites • You must...
User Guide - Page 104
...Software Recovery Window
From the Software Recovery window, you . The port LED turns solid green after the connection.
5. Recover the Switch Software
Chapter 5 Troubleshooting
4. Connect your management station directly to delete all the configuration settings on the switch, including the IP address, usernames, and passwords, but retain the software image. The Software Recovery window appears...
User Guide - Page 105
... Started Guide for features supported on the default software image are deleted and the switch returns to using the
factory default image.
Use this option to use the factory-default software image. Erase system configuration Use this option, you troubleshoot problems, see Chapter , "Cisco Support Resources."
If you select this option to delete all of the configuration settings...
Cisco ESW-520-48-K9 Reviews
We have not received any reviews for Cisco yet.