Cisco 857W - Integrated Services Router Support and Manuals
Cisco 857W Videos
Popular Cisco 857W Manual Pages
Configuration Guide - Page 14
... on these routers: • Cisco 850 Series and Cisco 870 Series Access Routers Cabling and Setup Quick Start Guide • Cisco 850 Series and Cisco 870 Series Access Routers Hardware Installation Guide • Cisco Router and Security Device Manager (SDM) Quick Start Guide • Cisco Access Router Wireless Configuration Guide • Upgrading Memory in Cisco 800 Series Routers •...
Configuration Guide - Page 23
....10.10.100 255.255.255.0 Router(config-int)#
Sets the IP address and subnet mask for an ATM interface.
Example:
Router(config-int)# no shutdown
Enables the ATM 0 interface. Configure the Wireless Interface
The wireless interface enables connection to the Cisco 857, Cisco 876, Cisco 877 and Cisco 878 models.
Perform these steps to global configuration mode. Ignore this step for the...
Configuration Guide - Page 42
...NAT for NAT.
interface type number
Example:
Router(config)# interface vlan 1 Router(config-if)#
Enters configuration mode for the VLAN (on the {interface type number | pool name} [overload] inside interface, packets sourced from addresses that can be translated to be set , as well as information about enabling static translation, see the Cisco IOS IP Command Reference, Volume 1 of...
Configuration Guide - Page 49
... Protocol) address negotiation.
OL-5332-01
Cisco 850 Series and Cisco 870 Series Access Routers Software Configuration Guide
4-3 Chapter 4 Configuring PPP over ATM with...specific destination subnetwork. Multiple PPPoA client sessions can be configured on the router, starting in global configuration mode.
Step 3 ip mtu bytes
Example:
Router(config-if)# ip mtu 4470 Router(config-if)#
Sets...
Configuration Guide - Page 63
... BOOTREPLY DHCPOFFER DHCPACK DHCPNAK Router#
Sent 0 0 0 0
Configure VLANs
Perform these steps to global configuration mode.
For details about this command and additional parameters that can be set, see the Cisco IOS Switching Services Command Reference.
OL-5332-01
Cisco 850 Series and Cisco 870 Series Access Routers Software Configuration Guide
5-5 Chapter 5 Configuring a LAN with...
Configuration Guide - Page 64
... to assign to privileged EXEC mode.
Example:
Router(config-if)# switchport access vlan 2 Router(config-if)#
Step 3 end
Example:
Router(config-if)# end Router#
Exits interface mode and returns to the VLAN. Verify Your VLAN Configuration
Use the following commands to the VLAN.
Router# vlan database Router(vlan)# show -Entered from privileged EXEC mode.
Displays summary configuration...
Configuration Guide - Page 83
...configuration mode:
Step 1
Command or Action aaa new-model
Purpose Enables the AAA access control model. username name {nopassword | password password | password encryption-type encrypted-password}
Example:
Router(config)# username cisco password 0 cisco Router(config)#
Establishes a username-based authentication system. Configure IPSec Transforms and Protocols
A transform set represents...
Configuration Guide - Page 92
... Firewall
1 Multiple networked devices-Desktops, laptop PCs, switches 2 Fast Ethernet LAN interface (the inside interface for NAT) 3 PPPoE or PPPoA client and firewall implementation-Cisco 851/871 or Cisco 857/876/877/878
series access router, respectively 4 Point at which NAT occurs 5 Protected network 6 Unprotected network 7 Fast Ethernet or ATM WAN interface (the outside interface...
Configuration Guide - Page 97
... has his own VLAN. See the Cisco Access Router Wireless Configuration Guide for more detailed information about configuring these Cisco routers in a wireless LAN application. Use the interface dot11radio global configuration CLI command to configure the router using the CLI.
CH A P T E R
9
Configuring a Wireless LAN Connection
The Cisco 850 and Cisco 870 series routers support a secure...
Configuration Guide - Page 98
... interface name number
Example:
Router(config)# interface dot11radio 0 Router(config-if)#
Step 2 broadcast-key [vlan vlan-id] change seconds
Example:
Router(config-if)# broadcast-key vlan 1 change 45 Router(config-if)#
Purpose Enters interface configuration mode for clients. See the Cisco IOS Commands for Access Points and Bridges for your wireless LAN, beginning in the "Configuration...
Configuration Guide - Page 100
...the Cisco Access Router Wireless Configuration Guide for available channel numbers.
(Optional) Specifies the role of bridging. The example specifies integrated routing and bridging. Configure Bridging on VLANs
Perform these steps to set up bridging on VLANs, beginning in global configuration mode:
Step 1
Command or Action bridge [number | crb | irb |mac-address-table]
Example:
Router(config...
Configuration Guide - Page 146
... ATM Errors
Router# debug atm errors ATM errors debugging is not adversely affected. Physical layer interface module (PLIM) type.
You can render your router CPU process, and it can find additional information and documentation about the debug commands in the Cisco IOS Debug Command Reference. The no form of this reason, use debug commands only to troubleshoot specific problems...
Configuration Guide - Page 158
...device that you see the Cisco IOS Release 12.3 documentation set. For example, you might need to the following Cisco IOS command modes are used in this case a router.
Because each mode, the prompt you can use the flowcontrol line configuration command. Each command mode supports specific Cisco IOS commands. When you begin a router session, you must reconfigure parameters...
Configuration Guide - Page 190
Index
Cisco IOS queues 10 class-based weighted fair queuing
See CBWFQ command conventions 13 command-line access to router
configuration example 11 configuring 9 command modes 2 to 4 commands -? 3 ? 4 abbreviating 6 access list 2 ATM troubleshooting 2 to 9 b 3 b flash 3 boot 3 completing 4 confreg 6 context 9 copy running-config startup-config 7 copy tftp flash 3 debug atm 6 debug atm errors 6 ...
Configuration Guide - Page 192
... 10 verify configuration 11 EIGRP configuration example 15 configuring 14 overview 2, 3 enable password recovering 12 setting 5 enable secret password recovering 12 setting 5 encapsulation 6 Enhanced Interior Gateway Routing Protocol See EIGRP error messages, configuration 6 error reporting, ROM monitor 8 errors, ATM, displaying 6 Ethernet 5 events, ATM, displaying 7 experience, user 11 extended...
Cisco 857W Reviews
Do you have an experience with the Cisco 857W that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!