Cisco 7604-RSP720C-R Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco 7604-RSP720C-R manuals!
Problems with Cisco 7604-RSP720C-R?
Ask a Question
Free Cisco 7604-RSP720C-R manuals!
Problems with Cisco 7604-RSP720C-R?
Ask a Question
Popular Cisco 7604-RSP720C-R Manual Pages
Configuration Guide - Page 9
... document comments to nexus7k-docfeedback@cisco.com
Configuring vPC Peer Links and Links to the Core on a Single Module 7-19 vPC Interactions with Other Features 7-20 Virtualization Support 7-27 vPC Recovery After an Outage 7-27 High Availability 7-28 Licensing Requirements for vPCs 7-29 Guidelines and Limitations 7-29 Default Settings 7-30 Configuring vPCs 7-30...
Configuration Guide - Page 16
...set of code
indicates a comment line.
Notes contain helpful suggestions or references to configure IEEE 802.1Q-in-Q (Q-in-Q) VLAN tunnels and Layer 2 protocol tunneling. Chapter 9, "Configuring Q-in-Q VLAN Tunnels" Describes how to material not covered in the manual... is in boldface screen font. Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
xvi
OL-23435-03...
Configuration Guide - Page 17
... directly to be careful.
The RSS feeds are a free service.
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
xvii Cisco currently supports RSS Version 2.0. Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What...
Configuration Guide - Page 19
... the interface types supported by the Cisco NX-OS software. Table 1-1
Interface Parameters
Feature Basic parameters
Layer 2
Parameters
Further Information
description, duplex, error disable, flow control, MTU, beacon
Chapter 2, "Configuring Basic Interface Parameters" of this document
Layer 2 access and trunk port settings
Chapter 3, "Configuring Layer 2 Interfaces" of this guide but some...
Configuration Guide - Page 23
...virtual device contexts (VDCs).
You must install this license on a supervisor switchover. OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
1-5 Chapter 1 Overview
Virtualization Interfaces
Send document comments to which you are in the correct VDC. Licensing Requirements for Interfaces
Interfaces support stateful and stateless restarts. After the...
Configuration Guide - Page 37
...Cisco-supported transceivers, use Cisco-supported transceivers.
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
2-13 To verify that the remote port send parameter is enabled or desired, set the Ethernet port speed to auto, the device automatically sets...to configure the port speed and duplex modes manually for a local port, consider the following:
...
Configuration Guide - Page 52
... startup-config
2-28
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 Note The interface speed that supports your changes for the local port. interface interface 3. exit 7. Configuring the Basic Interface Parameters
Chapter 2 Configuring Basic Interface Parameters
Send document comments to use a specific speed, you must set the remote port for...
Configuration Guide - Page 132
... BFD neighbor sets the TTL value to 255 and the local BFD process verifies the TTL value as 255 before processing the incoming packet.
For more information, see the Cisco NX-OS Licensing Guide. Any feature not included in that are listed with Cisco NX-OS Release 5.2, you . See the "Configuring BFD Support for Routing...
Configuration Guide - Page 223
... hot standby links.
See the Cisco Nexus 7000 Series NX-OS Layer 2 Switching Configuration Guide, Release 5.x, for information about ...
With M- series modules and LACP, vPC peer link supports 16 LACP interfaces: 8 active links and 8 hot standby...settings. If you must configure a list of parameters to be identical on the vPC peer devices on both vPC peer devices. Note When manually...
Configuration Guide - Page 225
...Cisco NX-OS Release 4.2(6) to address table synchronization across vPC peers using the reliable transport mechanism of address tables between the vPC peers. Note We recommend that the settings...OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
7-23 You should configure all belong to support faster convergence of the Cisco Fabric Service over Ethernet (CFSoE...
Configuration Guide - Page 228
...-switch link for the vPC peer link. CFSoE
The Cisco Fabric Services over Ethernet (CFSoE) is a reliable state transport mechanism... is not supported on the restored vPC peer device from going up , use -bia) for HSRP or manually configuring virtual ... enabled, the system displays an error message.
7-26
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03
...
Configuration Guide - Page 230
...support. The first vPC peer maintains its local ports. Note See the Cisco Nexus 7000 Series NX-OS High Availability and Redundancy Guide, Release 5.x, for LACP port roles. You must save this setting in the startup configuration. If at a time is upgraded... auto-recovery command. High Availability
During an In-Service Software Upgrade (ISSU), the software reload process on the first...
Configuration Guide - Page 267
.... When you enable PMTUD, the interface sets the Don't Fragment (DF) bit on all packets that the tunnel endpoint can receive ICMP messages generated by dynamically determining the lowest MTU along the path from a tunnel with Cisco NX-OS Release 4.2, you specifically configure another VDC. Virtualization Support
You can also configure what VRF to...
Configuration Guide - Page 268
...on to the switch. • You have installed the Enterprise Services license for Cisco NX-OS. • You must be familiar with Cisco NX-OS Release 5.2(5) and for later 5.2(x) ... and limitations:
• Cisco NX-OS supports the GRE Header defined in different Virtual Routing and Forward instances (VRF). Default Settings
Table 8-1 lists the default settings for IP tunnel parameters.
...
Configuration Guide - Page 283
... Series devices. Tunneled traffic cannot be edge ports.
• Dot1x tunneling is not supported.
• You should perform an EPLD upgrade to newer versions in these deployments.
• You must manually configure the 802.1Q interfaces to be routed.
• Cisco Nexus 7000 Series devices can provide only MAC-layer ACL/QoS for tunnel...
Cisco 7604-RSP720C-R Reviews
We have not received any reviews for Cisco yet.