Cisco 4500M Support and Manuals
Most Recent Cisco 4500M Questions
Popular Cisco 4500M Manual Pages
Software Guide - Page 24
... Means reader take note. A nonquoted set of text in the publication. System displays are grouped in italic screen font. Switching Services Command Reference - Cisco IOS IP Configuration Guide -
Arguments for which you supply values are in brackets and separated by vertical bars. Nonprinting characters such as passwords are optional. Command elements in square brackets are in...
Software Guide - Page 64
... can configure up to 16 hierarchical levels of network security.
Caution The service password-encryption command does not provide a high level of commands for each mode. Configuring Multiple Privilege Levels
By default, Cisco IOS software has two modes of security: • Setting the Privilege Level for a Command, page 3-16 • Changing the Default Privilege Level for Lines, page...
Software Guide - Page 122
... 4500 Series Switch
If your switch, the switch will not recognize one of the
power supplies.
Switch# show power supplies Power supplies needed by system: 1 indicates that the chassis and PoE requirements are brought up first, followed by IP phones.
• The maximum available power for chassis and PoE for the switch. Note The power redundancy-mode redundant command is in redundant...
Software Guide - Page 123
... the mathematical sum of the individual power supplies. The power supplies have a sharing ratio predetermined by system :2 Switch#
Available Power for Catalyst 4500 Series Switches Power Supplies
Table 7-3 lists the power available for the switch.
OL-6696-01
Software Configuration Guide-Release 12.2(25)EW
7-9 Note The power redundancy-mode combined command does not work on a Catalyst 4006...
Software Guide - Page 126
... rails to the Catalyst 4000 Series Installation Guide. Each Catalyst 4500 series module has different power requirements; The Catalyst 4006 switch contains holding bays for the Catalyst 4006 switch is designed and optimized for the modules + supervisor + fan cannot total more power than the power supplied by setting the power redundancy to support an optimized Catalyst 4006 chassis...
Software Guide - Page 127
The power supplies required 1 command sets the power redundancy to make use of 395 W:
• WS-X4014 supervisor engine-110 W
• Four WS-X4148-RJ modules-65 W each module in the chassis and as long as the show power command output.
Two 650 W power supplies supply only 750 W.
If the 400 W power supply fails, the backup 650 W power supply comes into reset mode. You need to remove ...
Software Guide - Page 129
.... OL-6696-01
Software Configuration Guide-Release 12.2(25)EW
7-15 Switch# show power command to 000d.edc6.daef 2.0
Ok
Switch#
Power Consumption of Chassis Components
For power consumption of all modules installed in reset mode. the "Status" displays it in the Catalyst 4500 Series Module Installation Guide. The Power supplies needed by placing it in the switch, you can power down to...
Software Guide - Page 515
... only IEEE 802.1q encapsulation.
• You cannot change the MAC address. This command promotes IP address overwriting and reuse in a DHCP environment. Configures a VLAN as a PVLAN, perform this problem, the Catalyst 4500 series switch supports the no ip sticky-arp command. To overwrite a sticky ARP entry, first delete the entry with the no keyword to clear PVLAN status.
Verifies...
Command Reference - Page 127
... cause. Specifies detection for the ARP inspection error-disable cause. Command Modes
Global configuration
Command History
Release 12.1(8a)EW
Modification Support for this command. Examples
This example shows how to recover an interface manually from a specific cause. Specifies error disable detection for the Catalyst 4500 Series Switches
errdisable detect
errdisable detect
To enable...
Command Reference - Page 354
... setting is hardware switched. show ip mroute
Chapter2 Cisco IOS Commands for the group was exceeded.
Information about the outgoing entry. Hardware switched
Timer: Interface state: (*, 224.0.255.1) (198.92.37.100/32, 224.0.255.1)
uptime expires
Description
For (*, G) entries, indicates that the entry was created because the SPT-Threshold for the Catalyst 4500 Series Switches...
Command Reference - Page 355
... packets. Expected interface for the Catalyst 4500 Series Switches
show ip mroute
Table2-16 show ip mroute Field Descriptions (continued)
Field RP...Cisco IOS documentation)
78-16201-01
Catalyst4500 Series SwitchCiscoIOS Command Reference-Release 12.2(18)EW
2-323
are they forwarded on the interface, the IP address of the packets; Following the slash (/), mode in sparse mode, this switch...
Command Reference - Page 356
... Cisco IOS Commands for the Catalyst 4500 Series Switches
show ip source binding
To display IP source bindings configured on the system, use the show ip source binding [ip-address] [mac-address] [dhcp-snooping | static] [vlan vlan-id ] [interface interface-name]
Syntax Description
ip-address mac-address dhcp-snooping static vlan vlan-id interface interface-name
(Optional) Binding IP address...
Command Reference - Page 408
... shows the configured mode for all modules:
Switch# show running-config 03:23:36:%SYS-5-CONFIG_I:Configured from console by consolesh runn Building configuration...
Examples
This example shows how to display module and status configuration for an interface.
power supplies required 1 ip subnet-zero
2-376
Catalyst4500 Series SwitchCiscoIOS Command Reference-Release 12.2(18)EW
78-16201...
Command Reference - Page 497
... entering the errdisable recovery cause psecure-violation global configuration command, or you can remove it by configuring some MAC addresses and allowing the rest to enable 802.1X on the Catalyst 4500 series switch. You cannot configure static secure MAC addresses in the error-disabled state, you can manually reenable it from this port age out immediately after...
Command Reference - Page 513
...mac command.
Command Modes
Privileged EXEC
Command History
Release 12.1(13)EW
Modification Support for the Catalyst 4500 Series Switches
traceroute mac ip
traceroute mac ip
To display the Layer 2 path taken by the packets from the specified source IP address or hostname to send Layer 2 trace queries and lets them time out. Defaults
This command has no default settings. IP hostname...
Cisco 4500M Reviews
Do you have an experience with the Cisco 4500M that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!