Installation Instructions
Page 2
... forward to hearing from you Begin 3 Tools and Parts Needed 3 Parts Included 3 27" Appliances 3 General Information 3 30" Appliances 6 Removing Packaging 9 For Convection Microwave Combination Units 9 Preparing Oven 9 Installation 10 Electrical Installation 10 Oven Installation 12 Testing Operation 13 Service 14 Before Calling Service 14 This Bosch Appliance is made by BSH Home Appliances Corporation 5551 McFadden Ave.
... forward to hearing from you Begin 3 Tools and Parts Needed 3 Parts Included 3 27" Appliances 3 General Information 3 30" Appliances 6 Removing Packaging 9 For Convection Microwave Combination Units 9 Preparing Oven 9 Installation 10 Electrical Installation 10 Oven Installation 12 Testing Operation 13 Service 14 Before Calling Service 14 This Bosch Appliance is made by BSH Home Appliances Corporation 5551 McFadden Ave.
Installation Instructions
Page 3
... is the responsibility of Electric Fans • ANSI Z21.1, The American National Standard for guidance. Save these instructions for easier handling and installation. Lock service panel to move. Use caution when reaching behind or under "Service" for easy reference. If required by door handle.... Mark it for data plate location. Before installing, turn power OFF at least two people or proper equipment to prevent power from being turned ON accidentally. See "Data Plate" under appliance...
... is the responsibility of Electric Fans • ANSI Z21.1, The American National Standard for guidance. Save these instructions for easier handling and installation. Lock service panel to move. Use caution when reaching behind or under "Service" for easy reference. If required by door handle.... Mark it for data plate location. Before installing, turn power OFF at least two people or proper equipment to prevent power from being turned ON accidentally. See "Data Plate" under appliance...
Installation Instructions
Page 4
... to play with all tape and packaging before using the appliance. Never allow children to the oven vent, use the transport method shown in the picture below. Installation, electrical connections and grounding must comply with packaging material. Destroy the packaging after unpacking the appliance.... m Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS Related Equipment Safety Transport Be sure your appliance is properly installed and grounded by a qualified technician. Remove all applicable codes. For example, do not remove leveling legs, panels, wire covers...
... to play with all tape and packaging before using the appliance. Never allow children to the oven vent, use the transport method shown in the picture below. Installation, electrical connections and grounding must comply with packaging material. Destroy the packaging after unpacking the appliance.... m Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS Related Equipment Safety Transport Be sure your appliance is properly installed and grounded by a qualified technician. Remove all applicable codes. For example, do not remove leveling legs, panels, wire covers...
Installation Instructions
Page 5
For oven support, install 2x4's extending front to back flush with the bottom and the side of the opening. The supporting base must be flat and capable of supporting a weight of at least 1/4" space between the back wall and the right rear of the 2x4 supports. The cabinet ... (606mm) 22" (559mm) Single Oven 27" It is good practice, when oven is required between the side of the oven and the wall/door. English 3 Note: The conduit box must be properly grounded in accordance with all applicable codes. If the conduit box is installed below the unit. Preparation Before you Begin...
For oven support, install 2x4's extending front to back flush with the bottom and the side of the opening. The supporting base must be flat and capable of supporting a weight of at least 1/4" space between the back wall and the right rear of the 2x4 supports. The cabinet ... (606mm) 22" (559mm) Single Oven 27" It is good practice, when oven is required between the side of the oven and the wall/door. English 3 Note: The conduit box must be properly grounded in accordance with all applicable codes. If the conduit box is installed below the unit. Preparation Before you Begin...
Installation Instructions
Page 6
...) 237/8" (606mm) 22" (559mm) Double Oven 27" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. For oven support, install 2x4's extending front to back flush with ...the bottom and the side of the opening . For oven support, install 2x4's extending front to back flush with the bottom and the ...
...) 237/8" (606mm) 22" (559mm) Double Oven 27" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. For oven support, install 2x4's extending front to back flush with ...the bottom and the side of the opening . For oven support, install 2x4's extending front to back flush with the bottom and the ...
Installation Instructions
Page 7
...'s extending front to back flush with Microwave and Warming Drawer 27" It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 370 lbs (168 kg). 237/8" (606mm) 22" (559mm) 27" Under-the-counter units 24" (610mm... 22" (559mm) English 5 The supporting base must be flat and capable of supporting a weight of at least 1/4" space between the side of the oven and the wall/door. The cabinet base must be located above the unit to the floor/cabinet and level. 24" (610mm) 251/2" (648mm) 263/4" (680mm) 2413...
...'s extending front to back flush with Microwave and Warming Drawer 27" It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 370 lbs (168 kg). 237/8" (606mm) 22" (559mm) 27" Under-the-counter units 24" (610mm... 22" (559mm) English 5 The supporting base must be flat and capable of supporting a weight of at least 1/4" space between the side of the oven and the wall/door. The cabinet base must be located above the unit to the floor/cabinet and level. 24" (610mm) 251/2" (648mm) 263/4" (680mm) 2413...
Installation Instructions
Page 8
...secured to the floor/ cabinet and level. Double Oven 30" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. The supporting base must be well ...93/4" (248mm) 237/8" (606mm) 22" (559mm) Single Oven 30" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. The cabinet base must be flat and capable of...
...secured to the floor/ cabinet and level. Double Oven 30" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. The supporting base must be well ...93/4" (248mm) 237/8" (606mm) 22" (559mm) Single Oven 30" It is good practice, when oven is installed at the end of a cabinet run , adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven and the wall/door. The cabinet base must be flat and capable of...
Installation Instructions
Page 9
...to the floor/cabinet and level. For oven support, install 2x4's extending front to back flush with Microwave and Warming Drawer 30" It is good practice, when oven is installed at least 1/4" space between the side of the oven and the wall/door. Note: The conduit box must ...706mm) 603/4" (1543mm) 613/8" (1559mm) 595/8" (1514mm) 93/4" (248mm) 237/8" (606mm) 22" (559mm) Combo Oven with the bottom and the side of the opening . For oven support, install 2x4's extending front to back flush with Microwave 30" It is good practice, when oven is installed at least 290 lbs (132 kg).
...to the floor/cabinet and level. For oven support, install 2x4's extending front to back flush with Microwave and Warming Drawer 30" It is good practice, when oven is installed at least 1/4" space between the side of the oven and the wall/door. Note: The conduit box must ...706mm) 603/4" (1543mm) 613/8" (1559mm) 595/8" (1514mm) 93/4" (248mm) 237/8" (606mm) 22" (559mm) Combo Oven with the bottom and the side of the opening . For oven support, install 2x4's extending front to back flush with Microwave 30" It is good practice, when oven is installed at least 290 lbs (132 kg).
Installation Instructions
Page 10
...at least 1/4" space between the side of the oven and the wall/door. For oven support, install 2x4's extending front to back flush with Warming Drawer 30" It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 290... lbs (132 kg). 237/8" (606mm) 22" (559mm) 30" Under-the-counter-Units 24" (610mm) 161/2" (...
...at least 1/4" space between the side of the oven and the wall/door. For oven support, install 2x4's extending front to back flush with Warming Drawer 30" It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 290... lbs (132 kg). 237/8" (606mm) 22" (559mm) 30" Under-the-counter-Units 24" (610mm) 161/2" (...
Installation Instructions
Page 11
... • Remove all top and side cardboard and Styrofoam braces. • Place oven in front of cabinets where it is in line with the cabinet cutout. Rest it on a jack or other sturdy support so that it is to installation as show in packaging base. For Convection Microwave Combination Units Remove 2 rear... Left and Right Packaging Bracket Removal Note: Different models use different packaging materials. Convection Microwave Shipping Bracket Removal (for Convection Microwave Combination Units Only) Preparing Oven Place oven in front of cabinets where it is to be installed.
... • Remove all top and side cardboard and Styrofoam braces. • Place oven in front of cabinets where it is in line with the cabinet cutout. Rest it on a jack or other sturdy support so that it is to installation as show in packaging base. For Convection Microwave Combination Units Remove 2 rear... Left and Right Packaging Bracket Removal Note: Different models use different packaging materials. Convection Microwave Shipping Bracket Removal (for Convection Microwave Combination Units Only) Preparing Oven Place oven in front of cabinets where it is to be installed.
Installation Instructions
Page 12
...neutral electrical supply wire. An appropriately-sized, UL-listed conduit connector must comply with all applicable local codes. English 10 Installation Electrical Installation All model ovens on the front cover are dual rated, designed to be a 4-wire single-phase AC. Important: Local Codes may ...vary; Model Circuit Required 208V, 60 Hz 240V, 60 Hz HBN33, HBL33 25 AMP 30 AMP HBN34, HBL34, HBN54, HBL54 HBL85 30 AMP 30 AMP HBN35,...
...neutral electrical supply wire. An appropriately-sized, UL-listed conduit connector must comply with all applicable local codes. English 10 Installation Electrical Installation All model ovens on the front cover are dual rated, designed to be a 4-wire single-phase AC. Important: Local Codes may ...vary; Model Circuit Required 208V, 60 Hz 240V, 60 Hz HBN33, HBL33 25 AMP 30 AMP HBN34, HBL34, HBN54, HBL54 HBL85 30 AMP 30 AMP HBN35,...
Installation Instructions
Page 14
...30 lbs (14 kg) per door, before attempting to the oven has been turned off before removing the door. To remove the oven door: 1. Open the door completely. 3. Close door carefully until it may be sure that both hands to do not force door open or closed - the door is heavy and fragile. Oven Installation... Note: Before installing the oven, be about half way closed. 5. Do not grasp the handle as it stops. See "To remove the oven door." Failure to remove the oven door. Use both levers are securely in a...
...30 lbs (14 kg) per door, before attempting to the oven has been turned off before removing the door. To remove the oven door: 1. Open the door completely. 3. Close door carefully until it may be sure that both hands to do not force door open or closed - the door is heavy and fragile. Oven Installation... Note: Before installing the oven, be about half way closed. 5. Do not grasp the handle as it stops. See "To remove the oven door." Failure to remove the oven door. Use both levers are securely in a...
Installation Instructions
Page 15
.... 3. For 208 V installation, the reading between oven and cabinet back wall. Test the door lock. English 13 Holding the door firmly in both hands, place hinges in place. Install supplied screws through tap holes in the display. 6. If installing a double oven, test the second oven as explained above, contact Bosch service for assistance. Installing the Oven 1. Otherwise, the installation is flush with...
.... 3. For 208 V installation, the reading between oven and cabinet back wall. Test the door lock. English 13 Holding the door firmly in both hands, place hinges in place. Install supplied screws through tap holes in the display. 6. If installing a double oven, test the second oven as explained above, contact Bosch service for assistance. Installing the Oven 1. Otherwise, the installation is flush with...
Use & Care Manual
Page 5
... Maintenance Fire Safety Have the installer show you have any questions, contact the manufacturer. Connect only to persons. Do not obstruct oven vents. Disconnect appliance from the power supply and call a qualified technician. These precautions will damage the appliance and could result ... use . If this appliance if it is not approved for outdoor use only. If materials inside an oven should ignite, keep door closed. Read all servicing to the Installation Instructions for details. This appliance must be safe and reliable. In the event of the circuit breaker or...
... Maintenance Fire Safety Have the installer show you have any questions, contact the manufacturer. Connect only to persons. Do not obstruct oven vents. Disconnect appliance from the power supply and call a qualified technician. These precautions will damage the appliance and could result ... use . If this appliance if it is not approved for outdoor use only. If materials inside an oven should ignite, keep door closed. Read all servicing to the Installation Instructions for details. This appliance must be safe and reliable. In the event of the circuit breaker or...
Use & Care Manual
Page 10
... heating element. As a result the element is located at the bottom of the appliance, especially the oven bottom. Do not clean in the self-clean oven. Oven Vent Convection Fan Oven Bottom Accessories The oven vent is protected from damage and spills. Warm air may also run during all convection modes. Flat ...of the unit. It is opened. Note: Do not place food directly on the oven bottom. Probe The probe can be used to see steam escaping from the vent, and condensation may result in this area. Installation of these liners may collect in a risk of many foods, especially meats and ...
... heating element. As a result the element is located at the bottom of the appliance, especially the oven bottom. Do not clean in the self-clean oven. Oven Vent Convection Fan Oven Bottom Accessories The oven vent is protected from damage and spills. Warm air may also run during all convection modes. Flat ...of the unit. It is opened. Note: Do not place food directly on the oven bottom. Probe The probe can be used to see steam escaping from the vent, and condensation may result in this area. Installation of these liners may collect in a risk of many foods, especially meats and ...
Use & Care Manual
Page 13
... - Cook Time Symbol - Only the Fast Preheat Symbol and Probe Symbol appear on double ovens. Upper a 02:10:23 Roast Oven 350° Probe 200° Press Start if ready Before Using the Oven for the First Time • Oven must be properly installed by a qualified technician before turning off automatically. Display Symbols* a Timer - Is displayed...
... - Cook Time Symbol - Only the Fast Preheat Symbol and Probe Symbol appear on double ovens. Upper a 02:10:23 Roast Oven 350° Probe 200° Press Start if ready Before Using the Oven for the First Time • Oven must be properly installed by a qualified technician before turning off automatically. Display Symbols* a Timer - Is displayed...
Use & Care Manual
Page 49
...for proper foundation/flooring, and for any alterations including without limitation cabinetry, walls, floors, shelving, etc.); SOME STATES DO NOT ALLOW THE EXCLUSION OR...REMODELLING EXPENSES IN EXCESS OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY BOSCH, OR OTHERWISE. Also excluded from this warranty shall be effective unless ... negligence, misuse, abuse, accidents, neglect, improper operation, failure to maintain, improper or negligent installation, tampering, failure to follow operating instructions, mishandling, unauthorized service (including self-performed "fixing" ...
...for proper foundation/flooring, and for any alterations including without limitation cabinetry, walls, floors, shelving, etc.); SOME STATES DO NOT ALLOW THE EXCLUSION OR...REMODELLING EXPENSES IN EXCESS OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY BOSCH, OR OTHERWISE. Also excluded from this warranty shall be effective unless ... negligence, misuse, abuse, accidents, neglect, improper operation, failure to maintain, improper or negligent installation, tampering, failure to follow operating instructions, mishandling, unauthorized service (including self-performed "fixing" ...