Asus RS520A-E11-RS12U Support and Manuals
Get Help and Manuals for this Asus item
View All Support Options Below
Free Asus RS520A-E11-RS12U manuals!
Problems with Asus RS520A-E11-RS12U?
Ask a Question
Free Asus RS520A-E11-RS12U manuals!
Problems with Asus RS520A-E11-RS12U?
Ask a Question
Popular Asus RS520A-E11-RS12U Manual Pages
User Manual - Page 9
...components into the barebone server. 4. Chapter 6: Driver Installation This chapter provides instructions for installing the necessary drivers for system integrators, and experienced users with the server. This chapter includes the motherboard layout, jumper settings, and connector locations. 5. Contents
This guide contains the following parts: 1. Chapter 1: Product Introduction
This chapter...
User Manual - Page 10
... Center (ACC) user guide
This manual tells how to complete a task. x Conventions
To ensure that you MUST follow to complete a task.
DANGER/WARNING: Information to prevent injury to yourself when trying to set up and use the proprietary ASUS server management utility.
Example: ++
Command Means that you must press the Enter or Return key...
User Manual - Page 13
The correct serial number of the product is required if you need to request for support from the ASUS Technical Support team.
12 34 RESET
RS520A-E11-RS12U
xxSxxxxxxxxx
ASUS RS520A-E11-RS12U
1-3 1.2 Serial number label
The product's serial number contains 12 characters such as xxSxxxxxxxxx and printed on the sticker at the server's front cover.
User Manual - Page 19
...I/O panel
The barebone server does not include a floppy disk drive. Standard model with no rear storage bay
1. A protection film is pre-attached to use a floppy disk.
SATA/SAS/NVMe back
panel 4. WARNING HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY
ASUS RS520A-E11-RS12U
1-9 Redundant Power supply 2. System fans 6.
1.6 Internal features
The barebone server includes...
User Manual - Page 21
...
System power ON
No activity
Read/write data into the storage device
System is pressed Normal status (Press the location switch again to turn off)
ASUS RS520A-E11-RS12U
1-11
User Manual - Page 25
... failed AGESA BL did not set PSP SMU reserved addresses via SVC call (no device on Knoll I2C bus) Null pointer passed to I2CKnollCheck Invalid device-ID found by verifying MAC
(continued on the next page)
ASUS RS520A-E11-RS12U
1-15 Timer wait parameter too large Test harness module reported an error x86 wrote C2PMSG_0 interrupting...
User Manual - Page 29
...Error Post Codes)
POST CODE...error/data corruption detected on the next page)
ASUS RS520A-E11-RS12U
1-19 SMU reported an error Function RunPostX86ReleaseUnitTests failed in case where not supported...to Mini BL Error in Validate and Loading AGESA APOB SVC call CcxSecBisiEn not set The UmcProgramKeys()... PSP-SMU message was revoked The platform model/vendor id fuse is not matching the BIOS...
User Manual - Page 63
...
3. Refer to the card. Install the software drivers for ISA or PCI devices. ...settings, if any. ASUS RS520A-E11 Series
2-31
Standard Interrupt assignments
IRQ Priority
Standard function
0
1 System Timer
1
2 Keyboard Controller
2
- 2.6.6 Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1. Turn on BIOS setup...
User Manual - Page 85
...ASUS RS520A-E11-RS12U
3-11 Refer to the left or right for a left pivot configuration or right pivot configuration. Install the rack rails into the rack.
2. Press the round button on the pivot receptor, then rotate the pivot receptor to section Rail Kit for the steps on installing... the rack rails into the rack. The CMA is designed with movable parts that allow you ...
User Manual - Page 87
Hook and loop fasteners
Cable fasteners
ASUS RS520A-E11-RS12U
3-13 Align and connect the pivot receptor on the CMA with the connector on the CMA to complete. Pass the cables from the server system through the hook and loop fasteners and the cable fasteners on the other intermediate rail.
7. 6.
User Manual - Page 91
...4-5
3. DMLAN setting (3-pin DM_IP_SEL1)
4-6
6. Power connectors (24-pin EATXPWR; 8-pin EATX12V1; 4-pin EATX12V2) 4-16
11. VGA connector (16-pin VGA_HDR1)
4-16
12. Hard disk activity LED connector (4-pin HDLED1)
4-17
14. BMC Debug UART connector (3-pin BMC_DEBUGUART1)
4-19
17. SLMPCIE SGPIO connector (6-1 pin SLM7_SGPIO1, SLM8_SGPIO1)
4-20
ASUS RS520A-E11-RS12U
4-3 Baseboard...
User Manual - Page 93
ASUS RS520A-E11-RS12U
4-5 2.
VGA controller setting (3-pin VGA_SW1) This jumper allows you to select which LAN NCSI function to use. Set to pins 1-2 to enable or disable the onboard VGA controller. LANNCSI setting (3-pin LANNCSI_SEL1) This jumper allows you to activate the VGA feature.
3.
User Manual - Page 95
... disable the Smart Ride Through (SmaRT) function. When enabled, SmaRT allows uninterrupted operation of the system during an AC loss event. ASUS RS520A-E11-RS12U
4-7 Set to pins 2-3 to function.
7. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) This jumper allows you to select which protocol in the GPU sensor to disable it. This feature is enabled...
User Manual - Page 97
... in soft-off mode. This is ON, in sleep mode, or in any motherboard component. The illustration below shows the location of the onboard LED.
2.
ASUS RS520A-E11-RS12U
4-9 Standby Power LED (SBPWR1) The motherboard comes with a standby power LED. 4.3 Internal LEDs
1.
User Manual - Page 99
Slim PCIe connector (SLMPCIE1-6) Connects the PCIe signal to support NVMe or SATA drives.
4.4 Internal connectors
1. Slim SATA PCIe connector (SLMSATA_PCIE7-8) Connects PCIe or SATA signal to backplane to the front riser card or NVMe port on the backplane.
2. ASUS RS520A-E11-RS12U
4-11
Asus RS520A-E11-RS12U Reviews
We have not received any reviews for Asus yet.