eMachines EL1352 Support Question
eMachines EL1352 Support Question
Find answers below for this question about eMachines EL1352.Need a eMachines EL1352 manual? We have 1 online manual for this item!
Question posted by onlyharley1 on April 2nd, 2014
My Emachine 1352 Won't Connect To Wireless Router
My son's el1352 will not connect to my verizon router. I bought a netgear adapter. I does show my home network but fails to connect. Do I need to buy a wifi net card instead?
Current Answers
Answer #1: Posted by freginold on May 9th, 2014 8:07 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
Hi, if your wireless adapter can "see" your network, then it should be able to connect, unless it does not support the necessary protocols to communicate with the router. Check:
- Make sure it supports whatever encryption/security protocol your router uses (WEP, WPA, etc.)
- Make sure it supports the Wi-Fi standard your router uses (802.11a, 802.11b, 802.11g, or 802.11n -- typically if the adapter supports any of the latter three, you should be fine)
- Make sure the adapter and the router are set for the same channel
- Make sure your router does not have MAC filtering turned on
- Make sure it supports whatever encryption/security protocol your router uses (WEP, WPA, etc.)
- Make sure it supports the Wi-Fi standard your router uses (802.11a, 802.11b, 802.11g, or 802.11n -- typically if the adapter supports any of the latter three, you should be fine)
- Make sure the adapter and the router are set for the same channel
- Make sure your router does not have MAC filtering turned on
Related eMachines EL1352 Manual Pages
User Guide - Page 2
Copyright © 2009. eMachines User Guide Original Issue: 06 / 2009
Model number Serial number Purchase date Place of purchase
Visit http://registration.emachines.com and discover the benefits of being an eMachines customer. All Rights Reserved.
User Guide - Page 3
... they may touch dangerous voltage points or short-out parts that the power outlet you need to disconnect power to the equipment, be blocked or covered. i Follow all power ...proper ventilation is easily accessible and located as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the power supply unit: Install the power supply unit before ...
User Guide - Page 9
... the World Wide Web 12
Connecting to a Web site 13 Downloading files 14 Ethernet networking 15 Wired Ethernet networking 15 Establishing your Ethernet network connection 20 Testing your network 20 Adding a printer to your network 21 Sharing resources 21 Using the network 23
Chapter 3: Troubleshooting 25
First steps 26 Troubleshooting 26
Add-in cards 27 Audio 27 CD or...
User Guide - Page 12
... information and maintenance instructions that are specific to your model of your notebook or desktop, a window will be sent a confirmation email with a more personable customer service... customer surveys
• The latest news from our trained
representatives
• Membership in the eMachines
community: receive promotions and participate in a safe place.
2 The second window you'll see...
User Guide - Page 14
.../2 keyboard port
Monitor (VGA) port
USB ports
Microphone jack (pink plug)
Headphone/analo g speakers jack (green plug) -ORFront speakers jack
PS/2 mouse port
Ethernet (network) jack
4
Description
Connects to the correct voltage for one of the following: Headphone: Plug headphones or amplified speakers into this jack (Default).
Plug a microphone into this jack...
User Guide - Page 15
Connects to devices such as a stereo) into this jack.
Stereo out: Plug your side left speakers ... into this jack so you can record sound on your computer (Default). Enables fast external disk access.
Supports high definition digital video connections.
5 Component
Icon
Center/subwoofer jack (orange plug) (optional)
Surround L/R speaker jack (black plug)
Audio in : Plug an external...
User Guide - Page 19
... loss or system damage. Protect your computer normally.
9 If you have a cable modem, use a surge protector that has an antenna/cable TV jack.
Preparing power connections
Protecting from reaching your computer during a power failure. If you have a telephone modem, use a surge protector that has a modem jack.
User Guide - Page 21
... on the back of your computer.
For the location, see "Back" on the modem at the back of the network cable into
the modem jack on page 4.
11 Connecting a dial-up a wired or wireless Ethernet network.
For the location, see "Back" on page 4. 2 Insert the other end of your computer. For information about setting...
User Guide - Page 22
... end of the modem cable into a telephone wall jack. (The modem will not work with digital or PBX telephone lines.)
3 If you want, you can connect a telephone to the PHONE jack on the modem on the back of the commercially available Web browsers, like Microsoft Internet Explorer or Netscape Navigator. A link...
User Guide - Page 23
... 3 To go to a different Web site, type the address (called a URL for example www.emachines.com), then click GO on the World Wide Web. The Web browser locates the server computer on the ...Web page displays on your screen depends on the method you use to connect to
your Internet account, you may need to start your connection will determine how fast Web pages display.
13 Click (Start), then ...
User Guide - Page 25
... electrician must install special Ethernet cables in the home. Most home networks are typically built using Fast or Gigabit Ethernet components. Using a router
The most common way to build computer networks in your wired Ethernet network, connect an access point to your home or office.
Business networks are built using a router.
The network is available at 1000 Mbps. To create...
User Guide - Page 26
... Chapter 2: Setting Up and Getting Started
Attached to the Internet. For a wired Ethernet network you need :
• Two or more computers with Ethernet jacks • One router • One broadband Internet connection (optional) • Ethernet cables connecting all Ethernet components should be either standard Ethernet (10 Mbps), Fast Ethernet (100 Mbps or 10/100), or...
User Guide - Page 27
...
• 4-port switch to eliminate the need to install Ethernet cards and drivers on the computers that comes with your ISP. If the connection is working , contact your Internet service provider. Before you change anything about your home setup, make the necessary arrangements with your Ethernet cards for
additional network hardware
• DHCP server/dynamic IP...
User Guide - Page 28
... the cable with the connectors facing away from you access the Internet connection from any network computer. The router can assign IP addresses to the computers on both ends of cable. Chapter 2: Setting Up and Getting Started
Connecting network cables We recommend using a router If you are attached to the copper pins in a different order (different...
User Guide - Page 29
... cable for each computer on the network. 5 For an Internet connection, plug a straight-through cable into the WAN port on the router and the other end into a grounded, 110V electrical outlet. 2 Turn on your computers. 3 Plug one end of the power adapter into the AC
connector on the router and the other end into the...
User Guide - Page 30
... server In order to each other. For instructions, see your router's documentation. If you are setting up your router (wired network) or access point (wireless network). When networking is set up a wired network, make sure that your home network is set to use the TCP/IP protocol on the network a unique Computer Name and the same Workgroup Name.
Configuring the...
User Guide - Page 31
...), then click Computer.
21
For information about sharing printers, see the instructions that has built-in networking. • Use a print server.
Important
To share a printer among the computers connected to the network. Follow the instructions included with your router or access point.
• Use a printer that came with your printer to install the printer...
User Guide - Page 59
If you did not purchase the hardware or software from eMachines, see :
• Online Help • Printed documentation • The Microsoft Windows
documentation
• The ..., then follow these recommendations before contacting Customer Care:
• Make sure that your computer is
connected correctly to a grounded AC power outlet that is turned on -screen prompts to complete the recovery.
User Guide - Page 66
... emergency use . AVOID EXPOSURE TO BEAM. In order to the same line as wireless LAN and/or Bluetooth modules).
Below information is DTMF tone dialing. The CD or...is located on local power, is available for products with this equipment is connected to operate within the limits for wireless use .
Digital audio output statement
The optical connector contains no guarantee that ...
User Guide - Page 69
...Galleria 2 6928 Manno Switzerland
Hereby declare that:
Product: Personal Computer
Trade Name: eMachines
Model Number: XXX series
SKU Number:XXX-xxx
("x" = 0~9, a ~ ... built with the following harmonized standards:
-. European single terminal connection
to assure that all the necessary steps have been taken and...Network (PSTN). EN55022, AS/NZS CISPR22, Class B -. EN61000-3-2 Class D -.
Similar Questions
Battery For Emachine
Where is the battery located on a desktop emachine PC model EL1352-07e
Where is the battery located on a desktop emachine PC model EL1352-07e
(Posted by mottosam 8 years ago)
After Reinstall, Xp Won't Recognize My Linksys Wmp54gv4 Wireless Router.
I did a nondestructive reinstall and redownloaded the drivers the eMachine's site reccomended. My 32...
I did a nondestructive reinstall and redownloaded the drivers the eMachine's site reccomended. My 32...
(Posted by jerrman 9 years ago)
Emachines El1352 Wireless Wifi Card
i m lookin for a wifi wireless card for my slim emachines el1353-07e slim tower..im not sure whr to ...
i m lookin for a wifi wireless card for my slim emachines el1353-07e slim tower..im not sure whr to ...
(Posted by leejeremy224 10 years ago)
My 3 Year Old Emachine El1850 Stop Communicating To My Router
(Posted by mikemarchi 10 years ago)
Connecting Two Monitors El1352-23e Nivida Geforce 6150se Graphics
I am trying to connect two monitors with a splitter and it is not showing that there are two monitor...
I am trying to connect two monitors with a splitter and it is not showing that there are two monitor...
(Posted by eyounger 11 years ago)