Zenith SL-4192-BK Support Question
Zenith SL-4192-BK Support Question
Find answers below for this question about Zenith SL-4192-BK - Heath - Six-Sided Die-Cast Aluminum Lantern.Need a Zenith SL-4192-BK manual? We have 1 online manual for this item!
Question posted by qxplt on November 25th, 2011
What Is The Wire That Says Not For Normal Instalation?
No instructions in the box.
Current Answers
Related Zenith SL-4192-BK Manual Pages
User Guide - Page 1
... 1, 5, or 10 minutes. TEST 1 5 10 MIN
AUTO
Set ON-TIME switch to use Manual Mode, the control
must be wired through a switch. • Some codes require installation by a
qualified electrician.
OPERATION
Motion Sensing Diecast Lantern
Mode: Test Auto Manual Accent
On-Time Works: Day Night
5 Seconds
xx
1, 5, or 10 Min
x
To Dawn*
x
3, 6 Hr, to...
User Guide - Page 2
...the control will continue to work as described in this feature.The motion sensing features will be in place while connecting the wires.
595-5628-08 Set sensitivity on half bright for the ON...-TIME (1, 5, or 10 minutes) then returns to dim mode.
1. SENSITIVITY
MIN
MAX
4. Mode Switching Summary
INSTALLATION
TEST
...
User Guide - Page 3
... on the X-bar. Secure the other lights from the motion sensor.
❒ Twist the junction box wires and the fixture wires together as to control other end of the system. Secure with wire connectors. Twist the wires together and secure with wire connectors. CAUTION: DO NOT connect the RED wire unless you want to the suitability of the "pigtail...
User Guide - Page 4
... you have selected the fixtures to the standard light's black wire. Connect all white wires together. Total fixture ratings must not exceed 360 Watts (3.0 A). When wiring to control a standard light fixture: Strip the motion sensor's red wire and connect to be controlled by this wiring. White
Black Green or Bare
(Standard)
White
Light Fixture
Light Fixture Red...
User Guide - Page 5
... the fixture onto the mounting screws and tighten nuts. Secure with decorative screws.
❒ After completing the tests on each side, and against the rubber bumpers at the bottom.
COMPLETE THE INSTALLATION
❒ Stuff the wires into the junction box. Note: As with any glass, handle with silicone weather sealant.
❒ Model 4193 only...
User Guide - Page 6
... to TEST position and DualBrite® switch to change temperature rapidly, such as heating vents and air conditioners. Motion
Motion
Note: Meets the ENERGY STAR® guidelines when DualBrite® function is off feature. Sensor
Least Sensitive
Most Sensitive
❒ Walk through the coverage area noting where you need to the OFF position.
User Guide - Page 7
... from other objects may be affecting the sensor. (Reduce sensitivity.)
595-5628-08
... may be installed in daylight. Light control is normal under these conditions...installation.
1. Light flashes on in a relatively dark location.
2. Light control is in Manual Mode. (Switch to an ON-TIME position.)
1.
Light control is in DualBrite® mode.
4.
Incorrect circuit wiring...
User Guide - Page 8
Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please ...experience a problem, follow this warranty in conjunction with our products. If you . Technical Service
Please call * for inconvenience, installation, setup time, loss of Purchase.
You may not apply to other expendable items are not covered by factory defective parts or ...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Heath Zenith Motion Sensor Light Wont Turn Off
(Posted by Tiighchairu 10 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)