Zanussi ZDI12001XA Support Question
Zanussi ZDI12001XA Support Question
Find answers below for this question about Zanussi ZDI12001XA.Need a Zanussi ZDI12001XA manual? We have 1 online manual for this item!
Question posted by Paulnchris on November 30th, 2014
No Water
There is no water coming in trough the water inlet, this has stopped in the past week, help.
Current Answers
Answer #1: Posted by TommyKervz on December 10th, 2014 8:34 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,823
Member since:
January 10th, 2013 Points: 17,776,823
follow the instructions on video below
Related Zanussi ZDI12001XA Manual Pages
Product Manaul - Page 2
... (BS 1362) fuse. Always pull the mains plug. • Only for a long time, let the water flow until it is no leakage. The appliance has a 13 amp mains plug. Always keep the instructions with... in the cutlery
basket with the power supply. jacent to the water supply. Water connection
• Make sure not to cause damage to the water hoses.
• Use only new hoses to connect the appliance ...
Product Manaul - Page 3
...• Do not sit or stand on the open door. • Dishwasher detergents are wet with the water in the appliance.
• Do not keep the appliance door open without...2 Filters
9
3 Rating plate
4 Rinse aid dispenser
8
5 Detergent dispenser
7
12
6 Salt container
6
2
7 Water hardness dial
5
3
8 Upper spray arm
4
9 Upper basket
Control panel
12
3
1 On/off the mains cable ...
Product Manaul - Page 4
... agrees with normal soil. Salt indicator. Contact your area. Make sure that the set level of water and energy
consumption for test information. 4) Use this programme to come out
from the appliance. If not,
4
adjust the water softener.
With this programme you can change the programme duration and the consumption values.
2) With this...
Product Manaul - Page 5
... 5.
5 Refer to the table to adjust the water softener to the position 1 or 2. The water softener neutralises these minerals. Make sure that the water softener uses the correct quantity of the water softener.
The number of flashes shows the level of dishwasher salt and water. Open the water tap.
5.
Water hardness
French degrees (°fH) 91 - 125 76...
Product Manaul - Page 6
...!
Water and salt can come out from the salt container when you fill the salt container, start a programme. Filling the rinse aid dispenser
Caution! quantity of the water softener...released when the lens (A) is aligned with the on/off indicator. Risk of water in the
salt container (only for dishwashers.
Each time you press the start button. Other products can cause damage to ...
Product Manaul - Page 7
... the programme.
Refer to the instructions on , fill the rinse aid dis-
Make sure that these tablets are dishwasher-safe.
• Do not put a small quantity of detergent. Add the detergent. 5. Open the water tap. 2. Refer to 'SETTING AND STARTING A PROGRAMME'. Refer to wash items that the appliance is in the appliance...
Product Manaul - Page 8
If you stop to use the combi detergent tablets, before you start indicator goes off indicator comes on the control panel. out dishes. 5. If the on/off indicator comes on and the phase indicators... - When you use separately detergent, rinse aid and dishwasher salt, do not fill the salt container and the rinse aid dispenser. Adjust the water softener to flash.
2. Turn the programme knob until...
Product Manaul - Page 9
Hot dishes can be easily damaged. There can be water on the sides and on the door of the appliance. Warning!
Make sure that it stops during operation.
9 Put them
from the appliance.
Only use abrasive products, abrasive cleaning pads or solvents.
Stainless steel becomes cool more quickly than the dishes. ...
Product Manaul - Page 10
... in operation when the problem occurred.
The fuse in the mains socket.
The water tap is clogged or there is set.
The water inlet hose has a kink or a bend.
Problem The appliance does not fill with water. The appliance does not fill with water. The delay start or wait for the end of interruption. The...
Product Manaul - Page 11
...solution
Clean the filters.
not sufficient . The programme was Increase the released quantity of the water softener agrees with a thin pointed object.
Limescale particles on the dishes.
There was not sufficient...wash all items.
The spray arms could not turn freely.
Make sure that there is dishwasher salt in the baskets is too much . If the problem occurs again, contact the ...
Product Manaul - Page 12
...Water supply pressure
Min. / max. (bar / MPa)
(0.5 / 0.05 ) / (8 / 0.8 )
Water supply 1)
Cold water or hot water2)
max. 60 °C
Capacity
Place settings
12
1) Connect the water inlet...help prevent potential negative consequences for the environment and human
health, which could otherwise be taken to the rating plate. Recycle the materials with a 3/4'' thread. 2) If the hot water comes...
Similar Questions
Zanussi Dishwasher Not Starting
all the lights are working on my dishwasher but it won't turn on
all the lights are working on my dishwasher but it won't turn on
(Posted by obbiew 3 years ago)
Zdf3023s Dishwasher Giving Error Message I60.
Starts normally but error message appears after 20 minutes and machine is overheating. Have replaced...
Starts normally but error message appears after 20 minutes and machine is overheating. Have replaced...
(Posted by jogram81 4 years ago)
Dishwasher Not Pumping Water
brand new dishwasher does not work. It has correct electrical and water install but once on does not...
brand new dishwasher does not work. It has correct electrical and water install but once on does not...
(Posted by Anonymous-122515 10 years ago)