Whirlpool WTW5640XW Support Question
Whirlpool WTW5640XW Support Question
Find answers below for this question about Whirlpool WTW5640XW.Need a Whirlpool WTW5640XW manual? We have 5 online manuals for this item!
Question posted by TLBergman on June 11th, 2017
Washer Wont Start
I've tried to reset several times, control panels lights up all cycles and beeps but when you press start button nothing
Current Answers
Answer #1: Posted by Odin on June 11th, 2017 6:02 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool WTW5640XW Manual Pages
Owners Manual - Page 3
... suds for the best performance.
When loading the washer with your load or allows time for clothes to produce the right amount of the cycle, as done in short pulses to determine the ...with dirty laundry, fill it evenly around the basket wall. Follow the manufacturer's instructions to determine the amount of the wash cycle, you start the cycle, the lid will lock, and the washer will ...
Owners Manual - Page 4
... your energy savings on your laundry load. As you to start of cycles.
3 CYCLE OPTIONS When you select a cycle, its default settings will leave your previous washer provided.
• Even in different energy usage. PRESOAK Use this option is used, the wash cycle will be a one-touch way to improve your washer. CONTROL PANEL AND FEATURES
2
3
4
1
5
3
1 ECO MONITOR Your...
Owners Manual - Page 5
... may affect the time shown in removing items as soon as cycle is normal. Fabric softener will hear the motor and washplate moving the load.
The Cycle Status Lights shows the progress of the cycle. SPIN
The washer spins the load at high speed.
The sensing process will start over when the washer is pressed, the washer will first perform...
Owners Manual - Page 7
... in loose heaps evenly around the washplate;
Try mixing different sized items to avoid pilling. Sort and ...lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because heat can set stains into washer
• Empty pockets. See "Cycle Guide" for best cleaning and to your laundry
2. USING YOUR WASHER...
Owners Manual - Page 8
...Overfilling dispenser will be dispensed into washer. It is closed completely, then press POWER to remain in the dispenser at correct time in the same cycle with a regular non-HE ...bleach laundry boost product, add to be selected to dispenser
Fabric softener tray
Add a measured amount of a cycle.
HELPFUL TIP: See "Washer Maintenance" for a small amount of the washer basket...
Owners Manual - Page 9
... desired. Dark colors that bleed or fade Light soils
Tap Cold This is lined up with a cycle, you will be cooler than what your faucet. 7. For more information, see "Control Panel". IMPORTANT: When delaying a cycle, use liquid HE detergent only in soil removal and to set a delayed Start: 1. Press START/Pause/Unlock to help dissolve detergents. Always read...
Owners Manual - Page 10
... washer is delayed for 2 to 3 minutes to filling. When the cycle has finished, the DONE indicator will light and the end of cycle ...cycle options
Select any spills.
2.
Press the START/Pause/Unlock button to restart the cycle. Close washer lid.
4. IMPORTANT: To avoid damaging the washer's finish, do not interrupt cycle. These can be interrupted, press Power and run a RINSE AND SPIN cycle...
Owners Manual - Page 11
... packing tray, place heavy blankets or towels into slot. Because some water may find laundry product residue leftover in washer or reconnect power. 3. Turn on RINSE AND SPIN cycle for about 30 seconds to mix antifreeze and remaining water. 3. Run washer through the following
recommended procedure:
To use , vacation, winter storage, or moving , or...
Owners Manual - Page 12
...basket if washer is normal to drainpipe or laundry tub. See "Cycle Guide" and "Using Your Washer" in firm contact with periodic gurgling or surging as expected
Not enough water in washer
Load not...It is not level. Drain hose connection.
See "Using Your Washer" for an HE low-water washer.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool....
Owners Manual - Page 13
... cycle. Ensure there is normal. Reset a tripped circuit breaker.
Do not interrupt cycle. You may take 2 to run or fill, washer stops working or wash light remains on (indicating that the washer ...hoses, which can slow or stop the washer.
Press Start/Pause/Unlock.
Always measure detergent and follow detergent directions based on .
The washer senses the dry load with short spins...
Owners Manual - Page 14
... try the solutions suggested here or visit our website at rinsing when the load is normal.
Cycles with high spin speeds. See "Using Your Washer" for assistance and to pump out water within ten minutes.
Dry spots on (indicating that inlet valve screens are still wet or spin light remains on load after washer has started...
Owners Manual - Page 15
... much HE detergent. Load dispensers before starting a cycle. Avoid overfilling. If you experience
Possible Causes
Solution
Washer not performing as recommended. Add an Extra Rinse to match your load with a slower wash action and spin speed, however items will be wetter than those using dispensers.
TROUBLESHOOTING
First try the solutions suggested here or visit...
Owners Manual - Page 16
... closed.
Always read and follow the manufacturer's directions. No sound when buttons are pressed
Button sounds are detected, the washer will add extra rinsing and pauses to possibly avoid a service call.
The lid is started. If excess suds are turned off by pressing and holding Cycle Signal for 5 seconds. Use only HE detergent. Be sure to avoid...
Dimension Guide - Page 1
... (113 mm) of washer. For complete details, see Installation Instructions packed with spacing of 0" (0 mm) clearance on all sides of 1" (25 mm) on the sides. A time-delay fuse or circuit breaker...standpipe must be at least 39" (990 mm) above floor; Top of washer. Floor drain system requires additional parts. Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Secure drain hose...
Installation Instructions - Page 2
...washers...washer.
Tools needed:
Parts needed: (Not supplied with washer... are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"...
Alternate parts: (Not supplied with washer)
Adjustable or open end wrench 9/...washer walk". Install your washer to 19⁄16" (39.5 mm)
Optional tools:
Flashlight
Bucket
Parts supplied:
NOTE: All parts supplied for your washer...
Installation Instructions - Page 3
... strap.
3
Recessed area or closet installation
3" (76 mm)
Minimum diameter for installation with water and load) of washer. If you must be at least 39" (990 mm) above floor; Top of laundry tub must support washer's total weight (with spacing of drain hose should be exposed to weather or in door are minimum...
Installation Instructions - Page 4
...location; If your washer includes a sound shield, please refer to the instructions included with a qualified electrician if you start: remove shipping ...washer onto cardboard before moving it is recommended that a qualified electrician determine that a separate circuit breaker serving only this time.
4 Remove shipping base
To avoid damaging floor, place cardboard supports from washer...
Installation Instructions - Page 5
Attach drain hose to remove all parts from rear panel. For a laundry tub or standpipe drain, go to free from tray.
For a floor drain, remove the preinstalled drain hose form... parts with clamp. NOTE: Keep tray in Step 7.
Be sure to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from tub
Connect Drain Hose
5. You may need to back of...
Installation Instructions - Page 6
...washer. Connect Inlet Hoses
Washer must be attached and have water flowing to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to hot water faucet. Repeat this step with flat washers... hoses if bulges, kinks, cuts, wear, or leaks are only connecting to faucets or washer. HELPFUL TIP: Make note of the drain hose. Screw coupling by hand until clear.
...
Installation Instructions - Page 7
....
HELPFUL TIP: You may want to turn the leveling foot clockwise to lower the washer or counterclockwise to reduce excess noise and vibration.
13. Adjust leveling feet
Jam nut
Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with a wood block or similar object that will...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Washer will not fill or start - Cabrio® washer with agitator
...Not filling or not starting the washer. Is there oversudsing? Cancel the current cycle. Re-select your desired cycle and press Start. Do not add ...cycle? Check the household faucets to the load once the washer started . Remove any accumulated film or particles from the washer. Make sure the Cycle control knob pointer is on some models only)? Is the Delay Wash status light... -
Washer will not fill - Front-load Duet washer
... of the three baffles is not cleaning laundry - Has a cycle been selected, but may not be connected to protect the washer during certain cycles. Washer will turn on water and check for leaks. Turn on ? Press and hold the End Of Cycle Signal button for proper fill. Is Delay Wash status light on the water. The water level on... -
Lint is on the load - Top-load washer
... low-twist terry cloth towels, will produce more lint in my top-load washer. Did you select a high-speed wash action cycle or a long wash time? Lint is not cleaning laundry - Sort loads before starting a new load of the washer before laundering. Also sort by paper or tissues left in a lower water level. The...
Similar Questions
Washer Wont Start Cycle
My washer didnt drain out so it still has some water in but i cant seem to get it to do anything it ...
My washer didnt drain out so it still has some water in but i cant seem to get it to do anything it ...
(Posted by Anonymous-85663 11 years ago)