Whirlpool WTW4950XW Support Question
Whirlpool WTW4950XW Support Question
Find answers below for this question about Whirlpool WTW4950XW.Need a Whirlpool WTW4950XW manual? We have 5 online manuals for this item!
Question posted by jerryhesby on May 28th, 2014
My Wtw4950xw1 Lid Will Not Lock So The Machine Will Not Start.
I can trick it into starting one cycle at a time by clearing the error codes. Will a new latch kit solve the problem?
Current Answers
Answer #1: Posted by Odin on May 28th, 2014 10:53 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
See http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/49-5--V1RXNDk1MFhX/Whirlpool-Washer-door-or-lid-won-t-lock. (Ignore the paragraph in red relating to a partial model number.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool WTW4950XW Manual Pages
Dimension Guide - Page 1
A time-delay fuse or circuit breaker is recommended that a separate circuit serving only this washer be at least 39" (990 mm) above floor; It is... with a door, the minimum ventilation openings in the top and bottom of washer. Laundry tub drain system
Minimum capacity: 20 gal. (76 L).
This washer has been tested for closet door ventilation openings which are required.
install no ...
Installation Instructions - Page 2
...Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 mm)
2 Install your washer... washer)
Your installation may require additional parts.
INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before starting ...
Installation Instructions - Page 3
...Minimum diameter for installation with maximum slope of washer. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285385), and an Extension Drain ... or in temperatures below the top of washer. n A level floor with spacing of washer. Water remaining in washer after use may be needed.)
Laundry tub drain system
Minimum capacity: 20 gal...
Installation Instructions - Page 4
...a 3 prong grounding plug. Set washer upright.
A time-delay fuse or circuit breaker is taped shut.
2.
NOTE: To avoid floor damage, set washer onto cardboard before moving it is ...codes permit and a separate ground wire is used, it and make sure lid is recommended. IMPORTANT: Removing shipping base is adequate. n This washer is equipped with a qualified electrician if you start...
Installation Instructions - Page 5
Be sure to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from tray. NOTE: Keep tray in case you need additional parts with... onto black drain port and secure with pliers and slide black elbow end of laundry tub. Drain hose form must be inside standpipe; You may need to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of...
Installation Instructions - Page 6
...Clear water lines
For floor drain installations, you must use a Y-adapter (not provided).
8. Do not use tape or sealants on washer. If you are found.
11. Connect inlet hoses to washer...to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to tighten couplings an ... new inlet hoses with cold water inlet valve. Repeat with flat washers (not provided). ...
Installation Instructions - Page 7
... adjustable wrench to reduce excess noise and vibration.
13. Secure drain hose
Laundry Tub
Standpipe
Wall
14. Check levelness of washer about 1/2" (13 mm) from the washer cabinet. Level Washer
IMPORTANT: Level washer properly to turn jam nuts counterclockwise on top edges of washer.
15. Adjust leveling feet
Jam nut
Secure drain hose to step 14...
Installation Instructions - Page 8
...cycle. q Check for leaks around faucets and inlet hoses.
q Check that washer is an extra part, go back through steps to complete full cycle.
8 q Check that you have all of washer... it into washer basket or detergent dispenser (on washer. Start washer and allow to see what was skipped.
Select any tape
remaining on some models). q Read "Washer Use" in your washer, measure ...
Owners Manual - Page 3
... of the cycle, as the lid lock goes through a self-test. It may also result in the basket.
Rather than diluting detergent as the washer determines the correct water level for your previous washer. And sometimes, you may hear nothing at the beginning of the clothes will find a step-by-step description in longer cycle times and...
Owners Manual - Page 4
... and Wash portions of cycles.
4 START/PAUSE/UNLOCK BUTTON Press to 3 minutes before locking again. Once the lid has locked the second time, the washer will hear the motor ...safe for additional details. NOTE: Avoid opening lid during a cycle.
press again to select a cycle for your washer. Select a wash temperature based on your laundry load.
CONTROL PANEL AND FEATURES
1
2...
Owners Manual - Page 5
... was selected. Press START/Pause/Unlock again to open the lid, press START/Pause/Unlock.
SPIN
The washer spins the load at high speed. The lid will come on. LID LOCKED To allow for proper load sensing and spinning, the lid will lock and the Lid Locked light will use a spray rinse. Avoid opening the lid during sensing. Some cycles will turn on...
Owners Manual - Page 7
... load evenly. It may also result in longer cycle times and reduced rinsing performance. Using Oxi or color-safe bleach: If using the Bulky Items cycle.
• Use mesh garment bags to help ... mildew. See "Cycle Guide" for tips and more information on using an Oxi or color-safe bleach laundry boost product, add to your laundry
2. Add a measured amount of the washer basket before adding ...
Owners Manual - Page 8
... pack or force items into washer
5. Add liquid chlorine bleach
to dispenser
This washer has been designed to ensure proper distribution at correct time in the rinse cycle. Always follow manufacturer's directions for correct amount of load. Close the lid and press the START/Pause/Unlock button again to pause the washer.
Pour a measured amount of Downy...
Owners Manual - Page 9
... Unlocking the lid to add garments If you select a cycle, select the desire wash Temperature by turning the Temperature knob to your wash cycles. Then close lid and press START/Pause/Unlock ...hot water heater setting. When the cycle has finished, the DONE indicator will unlock once the washer movement has stopped.
Promptly remove garments after cycle has completed to avoid odor, reduce...
Owners Manual - Page 10
....
Using recommended AFFRESH® washer cleaner,
add one tablet to washer basket OR If using your washer for a moment and pause, lid will lock, unlock, then cycle will not freeze. Turn off both water faucets; If cycle must be interrupted, Press and Hold START/Pause/Unlock for about 30 seconds to avoid damaging product over time.
3. Periodically inspect and...
Owners Manual - Page 11
... WASHER AGAIN
To reinstall washer after non-use washer again: 1. Before using again, run washer through BULKY ITEMS cycle to locate, level, and
connect washer. 2. TRANSPORTING YOUR WASHER
1. If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving : 1. Keep lid taped until washer is placed in washer or reconnect power.
3. Plug in new...
Owners Manual - Page 12
...or sagging.
The washer senses load sizes and adds correct amount of plywood under the Lid." See "What's New under your washer will take several minutes before washing. Washer may splash off... cycle for loading instructions.
Washer not performing as metal snaps, buckles, or zippers touch against the bottom of the cabinet. In Canada www.whirlpool.ca
If you have started the washer...
Owners Manual - Page 13
... items, rearrange load evenly in inlet hoses, which can slow or stop the washer. Close lid and press Start/Pause/Unlock.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and...detergent. NOTE: If problems continue, contact an electrician.
Not using HE detergent or using too much HE detergent. Do not interrupt cycle. You may take 2 to the washer. Do not add ...
Owners Manual - Page 15
... use spray rinsing will be wetter than those using correct cycle for the type of the basket before starting a cycle.
Use only liquid chlorine bleach in the bleach dispenser.
15
The suds from regular detergent can keep washer from operating correctly.
Washer senses load size and adds correct amount of water.
If using dispenser. http...
Owners Manual - Page 16
... starting wash load. Load with the lid open. Use cycle designed for the fabrics being washed. Always read and follow the manufacturer's directions. See "Cleaning Your Washer"...Lid Locked light is flashing
The lid is started.
Tie all strings and straps before washing to match your Washer" section. Mend rips and broken threads in Washer Maintenance. Add only 1 or 2 garments after washer...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Display shows oL - Top-load washer with Dispensers in Corners
... disconnect power for service. Find Manuals & The washer has attempted to fill and begin the wash cycle. Close the lid and press Start. Guides: /shared.whirlpoolcorp.com/service/modelnumber.jsp','modelnumber',500,480);return false;" href="#"> Lookup Model # Display shows an error code - If the washer is overloaded, it will drain any water and detergent that... -
Display shows F20 or FH - Front-load washer
...time after this will shut off the water to the washer and turned on ? Both hot and cold water must be able to pause or cancel the cycle for about 8 minutes while it will not be connected to the washer...washer? or This error code indicates a water supply problem. Completely open both the hot and cold water faucets turned on ; the washer...water pressure is started for proper ... -
Display shows dL - Top-load washer with Dispensers in Corners
... Corners Display shows oL - Top-load washer with Dispensers in Corners Display shows an error code - If the error remains on the display and the condition above has been checked, call for items caught in the lid that the washer lid is not locked. Front-load washer washer display shows dL. Display shows Ld - Check...
Similar Questions
Whirlpool Wtw4950xw The Sensing Light Comes On. The Lid Locks. It Tries To
start then nothing happens. the lid lock light then flashes and nothing happens. you cannot open lid...
start then nothing happens. the lid lock light then flashes and nothing happens. you cannot open lid...
(Posted by demoPri 10 years ago)
How To Bypass Lid Lock On Whirlpool Cabrio Washer
(Posted by luckishadow 10 years ago)
How To Perform Manual Lid Lock Test On Whirlpool Washer
(Posted by goodree 10 years ago)
Lid Lock Light Is Flashing When Lid Is Open And Washer Is Not In Use
If the lid lock is flashing when the lid is up and the washer is not in use how do I get the washer ...
If the lid lock is flashing when the lid is up and the washer is not in use how do I get the washer ...
(Posted by sruhl 11 years ago)