Home » Whirlpool » Laundry Washers » Whirlpool WET3300XQ

Whirlpool WET3300XQ Support Question

Find answers below for this question about Whirlpool WET3300XQ.
Need a Whirlpool WET3300XQ manual? We have 5 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by jgunion8 on June 20th, 2018

Proper Wiring Heating Elem Therm Fuse N Thermostat

Just replaced all 3 above parts not sure if wires were replaced properly but working ngetting heat

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on June 20th, 2018 3:41 PM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,467

1,100
points

If it's working properly then you wired it correctly!

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Whirlpool WET3300XQ Manual Pages

Installation Guide - Page 3

... screwdriver Adjustable or open-end wrench 9/16" (14 mm) 4" min (102 mm) Level Flashlight Bucket Parts supplied: NOTE: Remove parts package from the washer basket. Check that opens to 1" (25 mm) or hex-head socket wrench 1/4" nut driver (recommended) Wire stripper Caulking gun and compound (new vent installations) Utility knife 3 installation requirements Tools and...

Installation Guide - Page 5

... where it will need: n A location that allows for proper exhaust installation. This can cause damage in low temperatures. This washer/dryer has been tested for winterizing information. Mobile home installations require: n M etal exhaust system hardware, which is available for purchase from your washer in a basement, laundry room, closet, or recessed area. n S pecial provisions must...

Installation Guide - Page 8

... on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of electrical connection you are not sure the washer is not available, it here. Electrical Connection To properly install your outlet looks like this: 3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with upturned ends. If the dryer is recommended...

Installation Guide - Page 9

... required 4-wire, single-phase, 120/240 volt, 60 Hz, AC-only electrical supply on a separate 30-amp circuit, fused on both sides of the line. Be sure wall receptacle...electrical installer. ■■To be sure that you use Power Supply Cord Replacement Part Number 9831317. The cord is recommended. ELECTRICAL REQUIREMENTS - U.S.A. A time-delay fuse or circuit breaker is 5 ft. (1....

Installation Guide - Page 10

...drain hose. 10 There should be 2 cotter pins on the end of the washer/dryer until the jam nuts touch the washer. Move each foot to install leveling feet 1" (25 mm) Do not cut... Remove the hang tag and pin from washer/dryer. Tilt the washer/dryer back and remove the wood block. Pull yellow strap firmly, until the washer/dryer is required for proper leveling. This is level. NOTE: Do...

Installation Guide - Page 11

...screw C. Hole below terminal block cover 11 Then, go to "Venting Requirements." 4-wire direct connection: Go to "3-wire Power Supply Cord Connection" section. Then go to "4-wire Power Supply Cord Connection" section. Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to "4-wire Direct Wire Connection" section. Remove hold-down screw E. A. Center terminal block screw D.

Installation Guide - Page 12

Tighten strain relief screws just enough to strain relief 4-wire receptacle (NEMA type 14-30R) 4-prong plug Spade terminals with the dryer cabinet ... hole below the terminal block opening (B) so that the wire insulation on strain relief). Tighten screw. 12 Put the tabs of power supply cord under center terminal block screw (B). Be sure that one tab is pointing up (A) and the other ...

Installation Guide - Page 13

... cover with hold -down screw. 3. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Tighten screws. Now, go to "Venting Requirements." 3-wire Power Supply Cord Connection IMPORTANT: Use where local codes permit connecting cabinet-ground conductor to outer terminal block screws. Secure cover with upturned ends Ring...

Installation Guide - Page 14

... on strain relief). Cut 11/2" (38 mm) from end of wires into hooks. 2. Prepare to "4-Wire Direct Connection" on page 15. 14 Strip 5" (127 mm) of extra length so washer/dryer may be in a horizontal position. Attach direct wire strain relief A B C 4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes...

Installation Guide - Page 20

Connect Drain Hose Proper connection of laundry tub. IMPORTANT: Do not use any lubricant other than water. You may need to water leakage. Continue until hose contacts the ribbed stops on the side of the washer/dryer. Place clamp over the straight end of drain hose should be installed according to drain hose 3. Place...

Installation Guide - Page 23

... may want to step 2. Not Level LEVEL 2. HELPFUL TIP: You may want to make sure all four feet make solid contact with a wooden block. Level Washer/DRYER IMPORTANT: Level washer/dryer properly to raise the washer/dryer. or 4- Check levelness of washer/dryer. 4. Plug into a grounded 3- Rock washer/dryer back and forth to prop up front of...

Installation Guide - Page 24

...heat cycle (not an air cycle) for leaks around faucets and inlet hoses. q Check that the washer/dryer is an extra part, go away. 24 q Read the "Washer/Dryer Use and Care Guide." NOTE: You may be 2 household fuses...Keep the plastic foam for the dryer. Be sure the vent is first heated. q Check that the water faucets are tight. See "Level Washer/Dryer." In the U.S.A.: q ...

Warranty Information - Page 1

... be provided by calling Whirlpool. Replacement parts or repair labor on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing. 3. EXCLUSION OF...original purchase date is required to obtain service under this limited warranty. WHIRLPOOL CORPORATION LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major ...

Use & Care Guide - Page 5

... in the load. With Timed Dry, the dryer runs the amount of who installed the dryer. n Replace plastic or foil vent material with 4" (102 mm) diameter heavy, rigid vent material. 4" (102... dry laundry. During Automatic Dry cycles, drying air temperature or moisture level are not covered by the warranty and will be sure to follow the "Installation Instructions" supplied with heat, dryers...

Use & Care Guide - Page 15

...sure leveling legs are at fuse or breaker box. 2. Unplug or disconnect power to secure washer...washer/dryer base. 3. Doing so can cause longer drying times for an extended period of the dryer. See "Venting Requirements." As needed cleaning Laundry...washer/dryers: 1. For direct-wired washer/dryers: 1. Turn off valve to locate, level, and connect the washer/dryer. 15 Disconnect wiring...

Use & Care Guide - Page 18

...Replace any clogs from drain hose. Door must be rearranged to outlet. Remove several minutes before filling to determine if load is power to allow the washer to run or fill, washer stops working (cont.) Check proper... into a grounded outlet or reconnect power. opening. Washer not loaded as recommended. Remove any blown fuses. Lower drain hose if the end is normal. ...

Use & Care Guide - Page 21

... has been selected. Separate the load to check air movement. Fabric softener sheets blocking the grille. Make sure vent is a gas dryer. Dryer located in a room with lint. Proper operation of fuse. See "Installation Instructions." Replace both fuses or reset the circuit breaker. It is not crushed or kinked. Clothing knotted or balled up , the...

Use & Care Guide - Page 22

... cycle. In Canada www.whirlpool.ca If you may not have an odor. Replace both fuses or reset the circuit breaker. Dryer tightly packed. Laundry items were removed from the area, rewash and dry the clothing. The new electric heating element may not be cleaned before the end of wrinkles forming. All cycles are...

Use & Care Guide - Page 23

...LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring..., when this limited warranty. Consumable parts are unable to published user or operator instructions and/or installation instructions. 2. Replacement parts or repair labor on the product....

Dimension Guide - Page 2

...installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Laundry tub drain system Minimum capacity: 20 gal. (76 L). ...wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of washer/dryer. Floor drain system Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part...

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Dehumidifier will not run
... turned on ? Plug into a grounded 3 prong outlet? Is bucket installed properly? Empty bucket. Why is my dehumidifier's Empty or Adjust Bucket Light on ...bucket. Does bucket need to be serviced? Cleaning the dehumidifier Why isn't my dehumidifier collecting water? Has a fuse blown, or has a circuit breaker tripped? My dehumidifier runs, but doesn't dehumidify. Is the power cord ...
The burners on my gas modular downdraft cooktop won't light
...Replace the fuse or reset the breaker. Clean the burners using the following can cause the gas burners not to ignite My gas cooktop doesn't work on my range How do I clean the surface burners and electronic igniters on my gas modular downdraft cooktop? make sure... cleaning, make sure the alignment pins are properly aligned with the burner cap. See the illustration below .
Nothing will operate on my built-in electric convection oven
...closed. Heating elements will operate...works on my cooking appliance Blank display Error code on my built-in electric convection oven Why won 't open Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse...and actually be sure that there is power to the unit by looking for tripped breakers or blown fuses. Is the appliance wired properly? Check to...