Whirlpool WED9400ST Support Question
Whirlpool WED9400ST Support Question
Find answers below for this question about Whirlpool WED9400ST.Need a Whirlpool WED9400ST manual? We have 1 online manual for this item!
Current Answers
Related Whirlpool WED9400ST Manual Pages
Use and Care Manual - Page 1
ELECTRONIC ELECTRIC DRYER
For questions about features, operation/performance, accessories or service, call: 1-800-253-1301
or visit our website at... www.whidpooLcom
parts,
Table of Contents
2
W10110850A
Use and Care Manual - Page 2
... 9 Venting Requirements 14 Plan Vent System 15 Install Vent System 16 Install Leveling Legs 16 Connect Vent 17
Level Dryer 17 Complete Installation 17
DRYER USE 18 Starting Your Dryer 18 Stopping Your Dryer 19 Pausing or Restarting 19 Control Locked 19 Drying and Cycle Tips 19 Status Lights 20 Cycles 20 Additional Features...
Use and Care Manual - Page 3
... potential hazards that have the skills to carry out.
[] Do not use heat to play on your dryer. SAVE TH ESE iNSTRUCTiONS DRYERSAFETY
Your safety and the safety of others . You... containing foam rubber or similarly textured rubber-like materials.
[] Clean lint screen before using the dryer, follow instructions.
All safety messages will tell you what can be exposed to cooking oils in...
Use and Care Manual - Page 4
...93.98 cm)
Mobile home installations require metal exhaust system hardware available for purchase from the dealer from dryer drum. You may select a 10" (25.4 cm) or 15.5" (39.4 cm) pedestal.
See ...cm) above the floor.
4 Leveling legs NOTE: Do not use leveling legs if installing the dryer on a pedestal? Check that opens to the "Assistance or Service" section of approximately 48" ...
Use and Care Manual - Page 5
... considered.
To do so, you can purchase a Door Reversal and Stack Combination Kit. To do so, you may not operate correctly if dryer is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810.
See
"Venting Requirements."
• Aseparate 30-amp circuit.
• If you are installing your DUET ° washer...
Use and Care Manual - Page 6
...(2.5 cm)
(68.6 cm)
(2.5 crn) (2.5 crn) (80 cm) (12.7crn)
A
B
A. Installation spacing for this dryer. Dryer only
_o8"_ _A, ll tit Ill / \ lit tt_l
(96.52 cm
*Required spacing
1"* _ 2.8 cm
_-._27"--_ ... cabinet are acceptable.
• Companion appliance spacing should be considered. Dryer on the sides and rear.
Recommended installation spacing for cabinet installation
•...
Use and Care Manual - Page 7
... "Optional 3-wire connection" in "Electrical Connection" section.
The opening (such as the dryer exhaust opening. A 4-wire power supply connection must be using and follow the instructions provided...white wire) of electrical connection you must conform to introduce outside air into the dryer.
When the neutral ground wire is permanently connected to an individual branch circuit. ...
Use and Care Manual - Page 8
.... If your outlet looks like this :
3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with the circuit conductors and connected to whether the dryer is properly installed and grounded in a risk of NEMA Type 14-30R. If your outlet looks like this :
4-wire receptacle (14-30R) Then choose a 4-wire...
Use and Care Manual - Page 10
...wire insulation on strain relief). The strain relief should have a tight fit with the dryer cabinet and be Go to Section connecting to "Optional 3-wire connection" section.
4-wire connection...conduit connector onto the strain relief threads•
A. Neutral prong E. Spade terminals with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this...
Use and Care Manual - Page 11
...the terminal block, place the hooked end of the wire under the screw of extra length so dryer can be moved if needed. When connecting to external ground conductor screw. II
5, Tighten strain... from end of outer covering from external ground conductor
screw.
Dotted line shows position of dryer rear panel. Shape ends of wires into slot of NEUTRAL ground wire before being moved to...
Use and Care Manual - Page 12
...terminals with outer covering. Ring terminals G. Insert tab of terminal block cover into slot of dryer rear panel. 3. External ground conductor screw B. External ground conductor screw B. Center silver-colored...ends together. Tighten strain relief screw.
6. Insert tab of terminal block cover into slot of dryer rear panel. Neutral (white or center wire)
1. Ground wire (green or bare) of...
Use and Care Manual - Page 17
..., and start , check the following :
• There may notice a burning odor when the dryer is still no kinks in the flexible
gas line. 4. This odor is common when the heating element is level. If the dryer is closed.
11. See illustration.
3. Screw the legs into an outlet and/or electrical supply is connected.
•...
Use and Care Manual - Page 18
Place laundry in death, explosion, or fire. NOTE: A default time is displayed when an Automatic Cycle is selected.
...foam, rubber, or plastic must be changed without stopping the cycle. Failure to starting your load, by using Normal, which the dryer will adjust again, showing the final drying time. Press the WRINKLE SHIELD TM feature button if this appliance, This manual covers ...
Use and Care Manual - Page 19
... level.
• Press and hold the CONTROL LOCK/UNLOCK button for more than 5 minutes, the dryer will change by 5-minute intervals. I High Medium Low ExtraLow Air Only
Temperature
Adjst Manual Cyde_ Only
...cannot be used only with Manual Cycles. Cool Down tumbles the load without heat during dryer operation. To restart the dryer Close the door and press and hold DRY TIME, and the time will...
Use and Care Manual - Page 20
...as jackets, comforters and pillows• Rearrange the load halfway through the dryer cycle. Delicate Use this cycle to get Low heat to adjust the cycle length of the cycle.
d'_f<
You may...is reached in an Automatic Cycle.
• The dryer enters the cool down .
• In a Manual Cycle, if a wet item is not used with Manual Cycles. Laundry is detected. • In an Automatic Cycle, if...
Use and Care Manual - Page 21
... the actual time in the cycle by pressing the DRY TIME up to 120 minutes of heat-free, periodic tumbling at the end of drying time and a drying temperature. Drum Light ... turn on this cycle cannot be dried using Low heat. When a Manual Cycle is selected, the Estimated Time Remaining display shows the actual time remaining in the dryer too long.
Shower curtains, tablecloths
20 - 30
Rubber...
Use and Care Manual - Page 23
...dryer drum, positioning the back wire
on Dry the rack,
Stuffed toys or pillows Cotton or polyester fiber filled
Stuffed toys or pillows Foam rubber filled
Sneakers or canvas shoes
Timed Dry N/A
N/A
Low
60
Air Only 90 (no heat)
Air Only 90 (no heat... 23 This chart shows examples of the dryer.
DRYERCARE
Keep dryer area clear and free from dryer,
Place dryer at least 18 inches (46 cm) ...
Use and Care Manual - Page 24
... is probably clogged if lint falls off the screen with hot water.
3. Unplug dryer or disconnect power. 2. Unplug the power supply cord. Unplug dryer or disconnect power.
2.
IMPORTANT:
• Do not run the dryer with a damp cloth. 4. As needed cleaning Laundry detergent and fabric softener residue can cause longer drying times for an extended...
Use and Care Manual - Page 25
... power supply. Check with heavy metal or flexible metal vent. Was a regular fuse used for the dryer. Was the Start button firmly pressed? No heat
Has a household fuse blown, or has a circuit breaker tripped?
If the dryer hasn't been used ?
Are fabric softener sheets blocking the grille? Check that the exhaust vent is...
Use and Care Manual - Page 26
...dryer overloaded? Fabric softener sheets added to move and install dryer.
The new electric heating element may not be gone after the first cycle.
Place dryer at the end of garments being used ? Stains on load or drum
Was dryer...strips.
The load may have ventilation openings at the beginning of the dryer requires 5" (12.7 cm). Clean lint screen. Check for most ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How do I change the final food temperature using my Temperature Probe after my microwave oven has started ?
...element is loose - You can ensure that your new temperature is set by touching Probe Temp (to the first temperature you do I clean the Temperature Probe? Gas dryer Agitator is not heating with door open Dryer does not heat... food temperature using my Temperature Probe: Touch Probe Temp. You will resume heating to display the set temperature. Top-load washer Touch Start/Enter. How ... -
Cycle knob does not advance while running - Dryer
... the time selected. The cycle control knob should move with a large cotton load. Dryer The cycle knob does not advance while my dryer is wet, the cycle control knob will not start Dryer does not heat - In Automatic Dry or Accudry cycles, the knob moves based on the temperature... -
My dryer or load has an odor
... cycle to dry the load. To avoid this, do not run the dryer while painting, varnishing or refinishing near the dryer. Was a damp or wet load left in the washer or dryer for the first time? (Electric dryers) A new electric heating element may have an odor. If so, ventilate the area. When odors...
Similar Questions
F01 Error Pops Up On My Dryer
With the code above, I think I need to replace the electronic board. What is the part number I need ...
With the code above, I think I need to replace the electronic board. What is the part number I need ...
(Posted by tarynchesire 6 years ago)
Heating Element Stays On
I have a WED4800BQ dryer and the heating element is staying on after the door is opened and now it w...
I have a WED4800BQ dryer and the heating element is staying on after the door is opened and now it w...
(Posted by garner21856 7 years ago)
Install New Heat Element, Dryer Still Not Heating
install new heat elemen, dryer still not heating need help on what could be wrong. the dryer runs, c...
install new heat elemen, dryer still not heating need help on what could be wrong. the dryer runs, c...
(Posted by hayesp84 10 years ago)
Where Is The Heating Element On My Dryer Located
where is the heating element located on my whirlpool dryer mod no. LER4634PQ0
where is the heating element located on my whirlpool dryer mod no. LER4634PQ0
(Posted by chaunceeyoung 11 years ago)