Whirlpool CAM2752TQ Support Question
Whirlpool CAM2752TQ Support Question
Find answers below for this question about Whirlpool CAM2752TQ - COMMCL WSHR 2SP 3CYC WH DIG D.Need a Whirlpool CAM2752TQ manual? We have 1 online manual for this item!
Question posted by foaks on October 2nd, 2012
Agitator Removal
i am trying to replace the transmission, but i cant figure out to get the secondary cap off the agitator. Dos it unscrew (if so which direction) or does it pull out ?
Current Answers
Related Whirlpool CAM2752TQ Manual Pages
Installation Instructions - Page 1
www.whirlpool.com
COMMERCIAL WASHER
Paff No, 8315954 Rev, A
120-volt, 60-Hz Models
COMMERCIAL
LAUNDRY PRODUCTS Save Installation Instructions for
future reference.
Owner: Keep Installation Instructions for local
electrical inspector's use. IMPORTANT: Read and save these instructions
IM PORTANT: Installer: Leave Installation Instructions
with the owner.
Installation Instructions - Page 2
... the supply line where inlet pressure entering the building exceeds 100 PSI (690 kPa) to prevent damage to the washer mixing valve,
Untape and open washer lid, Remove packages and hoses from bottom of washer,
Support: Floor must be sturdy enough to reduce the chance of others .
Always read and obey all governing codes...
Installation Instructions - Page 3
... grounded 3-preng outlet installed by a quaifieq electrician.
3-pron groun_:P
plug _
power supply cord
ground
Figure 1
Do Not have a proper outlet installed by a qualified electrician,
WARNING - cm)
(I drain ... instructions
l_is washer may be installed in top and bottom are acceptable, Companion appliance spacing should be considered for installation:
17" (43cm)
Remove parts from ...
Installation Instructions - Page 4
... Check that hoso is not twisted or kinked and is the hot water faucet,
Pull firmly to faucet by
additional two-thirds turn, hand; See Step 6.
_;mAltach
...remove the end of shipping strap from one side of washer as shown,
Repeat with a permanent marker,
coupling
washer
m Insert a flat washer into the nearest hole in couplings,
Inlets are
found, When replacing your Whirlpool washer...
Installation Instructions - Page 5
... instructions for leaks, Tighten couplings if there is level, use adapter kit (provided with level,
When washer is leaking, Do Not overtighten; Remove cardboard or hardboard from parts package, Screw nut down , Make final check with unit), Replace meter case service door,
l_)a CHECK ELECTRICAL REQUIREMENTSB.ESUREYOU HAVE CORRECTELECTRICALSUPPLYAND RECOMMENDEDGROUNDING METHOD.
17.
Installation Instructions - Page 6
...
spin and cause poor rinsing, Operate the washer through a complete cycle with controls,
• Do not repair or replace any part of the washer or aftempt any servicing unless specifically recommended in...Before the washer is removed from service or discarded, remove the lid,
• Do not reach into the washer if the tub or agitator is moving,
• Do not install or store this washer where it...
Installation Instructions - Page 7
..." Ta e 2 te
It is recommended that are washed in the washer, run the washer through a complete cycle to rinse any type of the washer,
• Place both rear leveling legs in the washer that fiberglass items not be left in the washer,
(switch).
• Remove the front legs from the base of oil on it (including...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Hot water fills slowly - Top-load washers
... for leaks. Top-load washer Washer will not properly operate with agitator. Load-sensing Energy Star top-load washer with only one incoming source of hot water entering your prior washer. This is shut off the water and remove the inlet hoses from the washer. Straighten the hoses. Top-load washer The water temperature is to... -
How does Affresh washer cleaner eliminate odors?
... products currently on the market, Affresh tablets penetrate hard-to-reach areas to lift and remove the residue which builds over time in HE washers. It is safe for both washers and septic systems. For additional information on Affresh washer cleaner, click here Affresh washer cleaner or liquid chlorine bleach - How does Affresh... -
How do I remove odors from my Top-loading HE washer? Top-load HE with Dispensing Drawer
... before beginning the cleaning process. See also Why is damp, use a dehumidifier. How do I remove odors from the washer. Always do the following to the bleach dispenser. If the procedure does not sufficiently improve washer freshness, evaluate your laundry room is HE High Efficiency detergent required ? Maintenance procedure for other causes. Use of water...
Similar Questions
Trying To Remove The Top Half Of An Agitator But Cannot Get It Loose.
Want to replace a part because my agitator is not turning during washing. I have removed the entir...
Want to replace a part because my agitator is not turning during washing. I have removed the entir...
(Posted by Jrm175 11 years ago)
Can The Agitator Be Removed From The Machine?
The agitator in the machine is it possible to remove it?
The agitator in the machine is it possible to remove it?
(Posted by simataamoola 11 years ago)
Agitator Removal
Clothing is stuck under the agitator and I want to remove the agitator. The top cap comes off easy, ...
Clothing is stuck under the agitator and I want to remove the agitator. The top cap comes off easy, ...
(Posted by manyak 12 years ago)
How Do I Replace The Bellow In My Whirlpool Front Load Washer?
The bellow in my Whirlpool WFW9200SQ washer has a nick in it and is leaking. I need specific directi...
The bellow in my Whirlpool WFW9200SQ washer has a nick in it and is leaking. I need specific directi...
(Posted by kiansu 13 years ago)