Troy-Bilt TB2044 Support Question
Troy-Bilt TB2044 Support Question
Find answers below for this question about Troy-Bilt TB2044.Need a Troy-Bilt TB2044 manual? We have 1 online manual for this item!
Question posted by Allysonlindeman on June 11th, 2022
How Do I Remove The Trimmer Head From Tb 2044?
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Odin on June 12th, 2022 10:09 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,680
Member since:
April 10th, 2010 Points: 41,236,680
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt TB2044 Manual Pages
Operation Manual - Page 1
... MTD SOUTHWEST INC, All Rights Reserved.
11/12 For assistance regarding the assembly, controls, operation or maintenance of printing. Operator's Manual
Electric Start Capable 2-Cycle Trimmer
TB2044 XP
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 9 Operation 11 Maintenance 12 Cleaning and Storage 15...
Operation Manual - Page 2
...only in a well ventilated outdoor area.
• Be aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before starting the unit. Always loosen the ... and in serious injury or death to yourself or to possible dangers. All U.S. These can kill. Remove rocks, broken glass, nails, wire, string and other reproductive harm. Failure to liability or a fine...
Operation Manual - Page 3
...not touch or try to prevent unauthorized use or damage. It will do the job. Carefully remove vegetation and other debris that meet current ANSI Z87.1 standards and are available from all moving...should be in a stable position while starting position whenever pulling the starter rope. The cutting head remains stationary when the engine is not in the starting . Be in contact with water ...
Operation Manual - Page 4
... and void the warranty. Keep away from the operating area.
• HOT SURFACE
WARNING: Do not touch a hot muffler or cylinder. You may appear on trimmer attachment
shield. Failure to do not touch the line cutting blade.
4
Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded...
Operation Manual - Page 5
...
Other optional accessories may be used with cutting head, cutting head shield and handle 11 - 13 lbs. (5.0 - 5.9 kg) Trimmer Mechanism Bump Head Trimming Line Diameter 0.095 inches (2.41 mm) ...latest product information available at any time without notice.
5 KNOW YOUR UNIT
APPLICATIONS
As a trimmer: • Cutting grass and light weeds. • Edging • Decorative trimming around ...
Operation Manual - Page 6
...Push the handle down onto the shaft housing (Fig. 2). The bolt hole in the cutting head shield with a 3/8" socket until the handle is secure.
Align the
holes in the handle should.... 1
INSTALLING AND ADJUSTING THE HANDLE
Installing the Handle
1. Use the following instructions if the cutting head shield is firmly in the operating position (Fig. 11), move the handle to the right.
2....
Operation Manual - Page 7
... NOTE: To make sure the
release button is securely tightened. Installing the Attachment
NOTE: Remove the protective cap and gray spacer from the upper and lower shafts prior to loosen (Fig...1. NOTE: Do not tighten the nut (Fig. 4).
Knob
Fig. 3
Coupler
90˚ Edging Hole (Trimmer Only)
Nut Fig. 4
Upper Shaft Housing
Release Button
Lower Shaft Housing
Primary Hole Fig. 5
7 WARNING...
Operation Manual - Page 8
... as ethanol, methanol or MTBE (ether). Do not start the engine until fuel vapors dissipate.
1. Remove the fuel cap. 3. Use a separate fuel can severely damage the engine. Follow the instructions carefully ...damage this unit.
Keep sparks and open flames at least 30 ft. (9.1 m) from the area. WARNING: Remove the fuel cap slowly to the unit's fuel tank. oz.
(95 ml) 25 ml
MIXING RATIO - ...
Operation Manual - Page 10
...
Electric Start Port
STOPPING INSTRUCTIONS
1. Insert the electric start accessory into the electric start accessory operator's manual.
7. Idle the engine for 30 to 10 seconds. Remove the electric start , begin the starting position (Fig. 9).
6. the unit is properly warmed up for 5 to 60 seconds.
the engine does not start accessory from...
Operation Manual - Page 11
... the unit's
cutting efficiency and throws clippings away from the cutting head without the need for bending over.
OPERATION
HOLDING THE TRIMMER
WARNING: Always wear eye, hearing, hand, foot and
body protection... cutting head shield will make the unit overheat. NOTE: Do not rest the cutting head on bare ground or hard soil. Each time the bump knob is released. CAUTION: Do not remove or ...
Operation Manual - Page 12
... emission control devices and system may cause the engine to prevent the unit from the cutting head.
NOTE: Maintenance, replacement, or repair of any old trimming line and/or obstructions from ... the air filter. Other types of the cutting head (Fig. 15). These can break off and become dangerous projectiles. Always allow the unit to Removing Old Trimming Line and Obstructions.
2. If you ...
Operation Manual - Page 13
... oil. 6. Firmly press in poor performance or can cause permanent damage to cool before cleaning or maintaining the unit. Remove the air filter from
the cutting head.
1. Tab
2. Squeeze the air filter to secure the air filter cover. Engine failure due to the right and align the cover screw
with the cover...
Operation Manual - Page 14
...8226; the engine hesitates or stalls on acceleration • there is cracked, fouled or dirty, replace it from the cylinder head with a 5/8-inch socket, turning counterclockwise. If the engine
stops, use a small Phillips screwdriver to turn the idle speed screw... safety instructions to Starting and Stopping. 2. Clean around the spark plug. Remove the spark plug from the spark plug.
2.
Operation Manual - Page 15
...that has been stored for more than 30 days.
Remove the fuel cap, tip the unit and drain the fuel into the cylinder. Reinstall the fuel cap.
2. Remove the spark plug and put 5 drops of any ...moisture with the engine at the top. Remove the spark plug and drain all fuel has been drained from ...
Operation Manual - Page 16
... line is twisted
Not enough line is extended
Stop the engine and clean the cutting head Refill the cutting head with new line Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull...
Operation Manual - Page 20
... limitation may also have other than the amount of the purchase price of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for incidental or consequential loss or damages including, without assuming any other peril or natural disaster...
Similar Questions
Head Wont Stay On Shaft
how do u repair the trimmer so the head will stay on the shaft?
how do u repair the trimmer so the head will stay on the shaft?
(Posted by amandatackett29 8 years ago)
Trimmer Bump Head Feeding Problem
Bump head only feeds on one side, what can cause this?
Bump head only feeds on one side, what can cause this?
(Posted by johnnycom 8 years ago)
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
How To Remove Cutting Head From Tb525 Ec Trimmer
(Posted by godez 10 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)