Troy-Bilt TB2044 Support Question
Troy-Bilt TB2044 Support Question
Find answers below for this question about Troy-Bilt TB2044.Need a Troy-Bilt TB2044 manual? We have 1 online manual for this item!
Question posted by Anonymous-141463 on August 10th, 2014
How Do You Take Apart The Cutting Head?
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Troy-Bilt TB2044 Manual Pages
Operation Manual - Page 1
Operator's Manual
Electric Start Capable 2-Cycle Trimmer
TB2044 XP
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 9 Operation 11 Maintenance 12 Cleaning and Storage 15 ...
Operation Manual - Page 2
... the instructions carefully. Failure to obey a safety DANGER signal WILL result in a well ventilated outdoor area.
• Be aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before using the unit, all fasteners are in a clean, well-ventilated outdoor area where there are cracked...
Operation Manual - Page 3
...hold the unit with anything before repairing damage. Secure hair above shoulder level.
• The cutting head shield must be in daylight or good artificial light.
• Avoid accidental starting . Take...unit out of the reach of the shield.
• This unit has a clutch.
The cutting head remains stationary when the engine is dusty.
• Wear heavy long pants, boots, gloves ...
Operation Manual - Page 4
Failure to do not touch the line cutting blade.
4 Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded fuel.
• OIL Refer to the operator and/or bystanders.
&#...
Operation Manual - Page 5
... Muffler Throttle Lockout
ASSEMBLY TOOLS REQUIRED:
• #2 Phillips screwdriver • 3/8" Socket
Handle
On/Off Switch
Cutting Head
Shaft Housing
Cutting Head Shield
Coupler
Shaft Grip Throttle Control
Choke Lever
Starter Rope Grip
Air Filter Cover
Fuel Cap
Line Cutting Blade
Primer Bulb
SPECIFICATIONS*
Engine Type Air-Cooled, 2-Cycle Displacement 27 cc (1.64 cu. in.) Spark...
Operation Manual - Page 6
...of the shaft grip (Fig. 2).
4. Tighten the bolt with a 3/8" socket until the cutting head shield is not installed. Place it through the mount bracket and into the bolt hole and ...2. Tighten the bolt with a 3/8" socket until finger tight. 3. Use the following instructions if the cutting head shield is firmly in the mount bracket. (Fig. 1) 2.
Using a #2 Phillips screwdriver, tighten ...
Operation Manual - Page 11
.... • Hold the unit at waist level. • Keep the cutting head parallel to the ground so that the cutting head is at high speed. Attempting to release line in the operating position (Fig... left hand.
NOTE: Always keep the trimming line fully extended. NOTE: Do not rest the cutting head on bare ground or hard soil. NOTE: Some line breakage will make the unit overheat. For...
Operation Manual - Page 12
...unsure about 5 inches (12.7 cm) protrude from starting accidentally. If you are of the cutting head (Fig. 15).
DO NOT align the arrows when the line winding is complete. WARNING: ... attached to wind the line until a few inches protrude from the cutting head. Push
the line through the cutting head until about these required maintenance procedures at the frequency stated in the ...
Operation Manual - Page 13
...Push the spool cover onto the outer spool until
the tabs securely snap into the slots on the cutting head (Fig. 16). Rinse the air filter
thoroughly and allow it to dry. 4. Reinstall the air ...the right and align the cover screw
with clean SAE 30 oil. 5. Remove the air filter from
the cutting head.
1. Wash the air filter in the tabs on the air
filter cover (Fig. 22). 8. Tighten ...
Operation Manual - Page 14
... to Starting and Stopping. 2. Grasp the spark plug boot firmly and pull it from the cylinder head with a 5/8-inch socket, turning it with a replacement part #753-06193, a Champion RDJ7J or...boot.
0.025 in . (0.635 mm) (Fig. 24).
5. ADJUSTING THE IDLE SPEED
WARNING: The cutting head may spin during idle speed
adjustments. If the engine is cracked, fouled or dirty, replace it clockwise ...
Operation Manual - Page 16
...ENGINE WILL NOT ACCELERATE The fuel is old (over 30 days) and/or improperly mixed The cutting head is bound with grass The air filter is dirty
Drain the fuel tank and add fresh, properly...minutes before restarting the unit
THE CUTTING HEAD WILL NOT ADVANCE LINE The cutting head is bound with grass The cutting head is out of line The inner reel is bound up The cutting head is dirty The line is ...
Operation Manual - Page 20
...may not apply to state. Box 361131, Cleveland, OH 44136-0019. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars,
Cultivator... design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental or commercial purposes...
Similar Questions
How Do I Change Cutting Head On A Troybilt Tb625ec?
I can't figure out how to remove the old cutting head.
I can't figure out how to remove the old cutting head.
(Posted by dougclapp24 7 years ago)
Head Wont Stay On Shaft
how do u repair the trimmer so the head will stay on the shaft?
how do u repair the trimmer so the head will stay on the shaft?
(Posted by amandatackett29 8 years ago)
Trimmer Bump Head Feeding Problem
Bump head only feeds on one side, what can cause this?
Bump head only feeds on one side, what can cause this?
(Posted by johnnycom 8 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)