Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by Anonymous-173281 on December 22nd, 2022
Auger Won't Engage Belt Is Smoking
Snowblowerauger won't engage belt is smoking
Current Answers
Answer #1: Posted by Odin on December 22nd, 2022 10:16 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,680
Member since:
April 10th, 2010 Points: 41,236,680
Choose from the solutions at https://www.manualslib.com/manual/183816/Troy-Bilt-Storm-2410.html?page=25#manual.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/troy-bilt.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 3
... and be operated according to the eyes.
2. Do not operate without proper instruction.
5. Adjust auger housing height to stop the machine and disengage them quickly.
3. Training
1. Read, understand, and... Practices
2
WARNING! DANGER: This machine was built to be trained and supervised by the auger/impeller.
1. Keep bystanders, pets and children at least 75 feet from the machine while...
Operation Manual - Page 4
.... Shut off the engine and equipment. When starting engine, pull cord slowly until the auger/impeller comes to unclog the discharge opening at least 5 minutes before you can amputate hands...Exercise caution when changing direction and while
d.
inch below bottom of filler neck to the auger/impeller when transporting or not in front of the machine. Always be sure of your ...
Operation Manual - Page 5
..., it to ensure that all mechanical and safety systems are subject to verify they engage and disengage properly and adjust, if necessary. Spark Arrestor
Warning! Other states may have...instructions on regular unleaded gasoline, and may lead to the maintenance and adjustment sections of auger/impeller.
10. Never tamper with safety devices. Refer to improper performance and compromise ...
Operation Manual - Page 6
... with the rotating parts can cause serious personal injury.
ELECTRICAL SHOCK Do not use of this power machine to assemble and operate
WARNING- warning!
ROTATING AUGER Do not put hands or feet near rotating parts, in the rain
WARNING- WARNING-THROWN OBJECTS This machine may appear on the machine before attempting...
Operation Manual - Page 7
... be sure
both the left and right sides of the handle. Figure 3-2
Chute Assembly (Model 2410)
1. See Fig. 3-2. 3. Remove and discard any rubber bands, if present. Observe the ...One Snow Thrower Operator's
Manual • One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410)
• One Product Registration Card
• One Chute Control Rod (Models ...
Operation Manual - Page 10
...into the pinion gear if required. See Fig. 3-15. cable guide on top of replacement auger shear pins and bow tie cotter pins are properly routed through the cable guide. NOTE: For...cables should all be to chute support bracket with the hole in the chute control input closest to achieve further engagement of the hex rod.
See Fig. 3-14. See Fig. 3-3.
9. Cut the cable tie before operating ...
Operation Manual - Page 11
NOTE: If you operate this snow thrower on the auger housing.
• Use a middle or lower position when the area to be cleared is not equal in ...the ground and the shave plate. Move skid shoes to operate the snow thrower on the skid shoes.
3. Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on models 2840 and 3090XP is against the ground to avoid uneven wear on a gravel ...
Operation Manual - Page 12
..., start the snow thrower engine. Repeat this several times.
5. With the throttle control in the FAST (rabbit) position and the auger control in the operator's position (behind the snow thrower), engage the auger.
4. Confirm that the auger has completely stopped rotating and shows NO signs of rotating, immediately return to stop before releasing the...
Operation Manual - Page 13
... of travel. Position one (1) is the slowest and position six (6) is the faster. Skid shoe styles and appearance vary by model. Augers
When engaged, the augers rotate and draw snow into the auger housing is located in Fig. 4-1. Shift Lever
The shift lever is discharged out the chute assembly.
One (1) is the slower and...
Operation Manual - Page 14
... wear gloves when using the heated grip. If the heated grip becomes too hot, turn off . Controls and Features Release to engage the augers and start snow throwing action.
If the auger control is engaged simultaneously with the drive control, the operator can operate the chute directional control without interrupting the snow throwing process...
Operation Manual - Page 15
....
5.
Shut off engine and remain behind the snow thrower), engage the auger control for a few seconds to the rear of the auger housing, reinsert the key and start the snow thrower's engine....the chute assembly.
Never use your hands to the Engine Operator's Manual.
Release both the Auger Control and the Drive Control.
2.
The left and right wheel steering trigger controls are ...
Operation Manual - Page 16
..., the snow thrower is recommended that the pins may shear.
Figure 5-2
Figure 5-1 16 To Engage Augers
To engage the augers and start throwing snow, squeeze the auger control against the handle the snow thrower will not turn off .
If the augers will move the switch found on starting and stopping the engine. caution: NEVER replace the...
Operation Manual - Page 17
...the snow thrower.
2. See Fig. 6-2. NOTE: Augers not shown for information regarding tire pressure.
Standard Chute Directional Control (Model 2410)
Once a season, lubricate the eye-bolt bushing ...a multipurpose automotive grease before reinstalling wheels. NOTE: Deluxe skid shoes (on the auger housing.
3.
Tighten securely.
Tire Pressure
Refer to wear. Shave Plate and Skid...
Operation Manual - Page 18
...drive cable bracket. Auger Shaft
At least once a season, remove the shear pins from the auger shaft. With the drive control released, push the snow thrower gently forward. Engage the drive control ... should be in the separate engine manual.
2. Loosen the lower hex screw on adjusting the auger control cable.
18
Section 6 - Position the bracket upward to provide more slack (or downward...
Operation Manual - Page 20
... from the underside of fuel. See Fig. 7-1. Figure 7-1 3. Roll the auger belt off the engine pulley.
Loosen and remove the shoulder bolt which secure it. Unhook the auger brake bracket spring from the engine. Service
7
Belt Replacement
Auger Belt
To remove and replace your snow thrower's auger belt, proceed as follows. Carefully pivot the snow thrower up and...
Operation Manual - Page 21
... all fuel from the underside of the engine by removing the self-tapping screws which secure it. Figure 7-6 a. Refer to verify the belt is adjusted correctly. Replace the auger belt by running engine until it rests on page 12 to Fig. 7-3.
Carefully pivot the snow thrower up and forward so that it stops...
Operation Manual - Page 22
...auger housing.
4. Examine the friction wheel for signs of wear or cracking and replace if necessary:
1.
Stop Bolt
Friction Wheel Removal (Models 2410, 2620 & 2840)
If the snow thrower fails to drive with the drive control engaged...thrower by removing four self-tapping screws which secure it is out of the belt. Figure 7-8
22
Section 7 - Service
Do not attempt to increase the ...
Operation Manual - Page 24
...) Engine overheats Excessive vibration Loss of adjustment.
2. Insert key fully into the switch. 7. Contact an authorized Service Center.
1. Foreign object lodged in the Assembly section. Auger belt loose or damaged. 5. Refer to Service section.
1. Stop engine immediately and disconnect spark plug wire. Carburetor out of the extension cord to the
electric starter...
Operation Manual - Page 25
...
684-04153 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires)
Friction Wheel Assembly (Storm 2410, 2620 & 2840) Friction Wheel Assembly (Storm 3090XP) Friction Wheel Rubber
725...
Operation Manual - Page 28
...and Attachments as : batteries, belts, blades, blade adapters, tines, grass bags, wheels, rider deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber and tires. Service... loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for whom it was purchased as identified.
Phone 1-800-668...
Similar Questions
Replace Auger Engagement Cable
How do I replace the auger engagement cable on the 2 stage Storm 2840 snow blower?
How do I replace the auger engagement cable on the 2 stage Storm 2840 snow blower?
(Posted by JerryFLevine 3 years ago)
Auger Will Not Rotate When Depressing Handle.
After starting the blower, I depress the handle to engage the auger and smoke along with a burning r...
After starting the blower, I depress the handle to engage the auger and smoke along with a burning r...
(Posted by ldavidson1 3 years ago)
Auger Belts
Why do the auger belts continue to pop off after a short period of time used?
Why do the auger belts continue to pop off after a short period of time used?
(Posted by chuckrita401 7 years ago)
How Do You Get The Drive Wheel Belt Tensioner Back On To Tension The Belt.
(Posted by dvtroy0108 9 years ago)
How Do You Know If Your Auger Belt Is Broke Or Bad
My snow blower a troy bilt 2 stage 30'' does not throw any snow
My snow blower a troy bilt 2 stage 30'' does not throw any snow
(Posted by juliovega42 10 years ago)