Troy-Bilt Horse Support Question
Troy-Bilt Horse Support Question
Find answers below for this question about Troy-Bilt Horse.Need a Troy-Bilt Horse manual? We have 2 online manuals for this item!
Question posted by Anonymous-152185 on June 21st, 2015
Pto Cable
i need help on putting on a PTO cable on a Troy built horse riding mower
Current Answers
Answer #1: Posted by TommyKervz on June 21st, 2015 1:55 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,843
Member since:
January 10th, 2013 Points: 17,776,843
Download the operation manual here and follow the instructions on page 24.
Related Troy-Bilt Horse Manual Pages
Operation Manual - Page 1
Printed In USA
TROY-BILT, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-07569 (November 1, 2011)
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Hydrostatic Lawn Tractor -
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Horse
WARNING
READ AND ...
Operation Manual - Page 2
...model plate by looking beneath the seat. Troy-Bilt reserves the right to provide excellent performance when properly operated and maintained. You can seek help from the options below: ◊ Visit...all times. We want to all times.
Table of product specifications for purchasing a Troy-Bilt Lawn Tractor. If you for various models. All information in the provided area to operating ...
Operation Manual - Page 3
... Do not operate the mower
anyone . without proper
slacks and shirts. CALIFORNIA PROPOSITION 65
WARNING! This machine was built to be picked up...help avoid blade contact or a thrown object injury,
bare feet or sandals. Stop machine if
and do not point it is capable of the mower...area where the equipment is to be
instruction. Do not put hands or feet near rotating parts or under 14 years...
Operation Manual - Page 4
... tall, dry grass (e.g., pasture) or piles of alcohol or drugs.
16.
machine by putting your foot on
hazard. If situations occur which could cause serious injury. Contact your safety,...cart, lawn roller, etc.) on any adjustments.
21. Back up on ramp(s) to a complete stop engine and wait 3. Operate the machine smoothly. Do not attempt to take advantage of riding mower-related...
Operation Manual - Page 9
...for instructions on your riding mower. Position the red rubber boot over the positive battery terminal to help protect it clockwise.
CAUTION: When attaching battery cables, always
connect the ...harm.
To connect the battery cables, proceed as instructed in serious personal injury and/or property damage.
9 The negative battery terminal is put into service after handling. WARNING!...
Operation Manual - Page 12
... in Fig 4-1 and described on the following pages. Controls and Features
Throttle/Choke Lever
Brake Pedal
4
Ammeter
Parking Brake Lever
Speed Control Lever Cup Holder
PTO (Blade Engage) Lever
Ignition Switch Module
Deck Lift Lever
Figure 4-1 Lawn Tractor controls and features are illustrated in personal injury.
12
WARNING!
Operation Manual - Page 13
...When operating the tractor with the speed control lever engaged as the direction of the lawn tractor. The headlights will result in premature wear of regular operation will be certain that... of the engine and, when pushed all the way forward, the choke control also.
Always disengage PTO, move the speed control lever to the "N" neutral position. IMPORTANT: Prior to operating the tractor,...
Operation Manual - Page 14
...and then immediately move the lever all the way down and into the PTO OFF position disengages power to start the engine. Doing so will automatically ...lawn tractor. Move the parking brake lever all the way forward. The parking brake lever is located on the tractor's right fender, the PTO (blade engage) lever is used to engage power to stop the tractor under normal circumstances. PTO...
Operation Manual - Page 15
... will automatically shut off if the operator leaves the tractor's seat with the blades (PTO) engaged. Start the engine as instructed on page 16 under Starting
The Engine. 2.... Caution Mode
Position
Start Position
Safety Interlock Switches
This tractor is equipped with the cutting blades (PTO) engaged.
5. Contact an authorized Troybilt service dealer.
• The safety interlock system prevents ...
Operation Manual - Page 16
...move the speed control lever to engage.
Refer to the START position. Place the PTO (blade engage) lever in neutral, set parking brake, stop and then immediately move the parking brake ...lever out of having your lawn "browned" by fully depressing the parking brake pedal and keeping it down with the throttle control ...
Operation Manual - Page 17
...:
1.
Mowing
WARNING!
Operation
17 Engaging the Blades
Engaging the PTO (Blade Engage) transfers power to the cutting deck or other...throttle.
• Under heavier conditions it is designed to mow lawns, NOT clear brush.
• Keep the blades sharp and ...obstacles.
• Avoid turns when driving on a slope. To help determine slopes where you may be cut the grass too short....
Operation Manual - Page 19
...at least once a season with your unit.
Before lubricating, repairing, or inspecting, always disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to ...the crankcase to expose the drain port. Before performing any maintenance or repairs, disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key...
Operation Manual - Page 20
... water solution. See Fig. 6-2. IMPORTANT: After cleaning your lawn, near enough for battery failure are:
• Incorrect initial...washer to both terminals.
• Always keep the battery cables and terminals clean and free of corrosive build-up.
&#...electrical components, spindles, pulleys, bearings or the engine. Disengage the PTO (Blade Engage), set the parking brake and stop the engine.
...
Operation Manual - Page 21
... the lever for lifting the platform on a firm, level surface, place the deck lift lever in need of adjustment. Measure the distance from the outside of the deck.
Both measurements taken should be mowing..., if necessary, to the Set-Up and Assembly section of the deck.
4. Always disengage PTO, move shift lever into neutral position, stop when the brake pedal is completely depressed, or ...
Operation Manual - Page 23
Service
Cutting Deck Removal
To remove the cutting deck, proceed as seen in the disengaged (OFF)
position and engage the parking brake. 2. Place the PTO (Blade Engage) lever in Fig. 7-3. Remove the bow-tie cotter pin and flat washer securing the
deck stabilizer rod to raise the deck lift arms ...
Operation Manual - Page 24
... your tractor has not been put into use a fuse with the same amperage capacity for sharpening or replacement. If the charger is :
• Approximately 10 psi for the rear tires
• Approximately 14 psi for exact tire manufacturer's recommended or maximum psi. Service Carefully remove the PTO cable from damage caused by using...
Operation Manual - Page 27
...once at a high cutting height, then
mow again at high RPM Engine Idles rough Excessive vibration Mower will not mulch grass
Uneven cut
Cause
1. Sharpen or replace blade. 1. Blocked fuel line. ...or replace plug. 6. Replace air cleaner element and/or clean
pre-cleaner, if so equipped. 1. PTO/Blade engaged.
2. Vent in correct starting
position. 1. Engine oil level low.
2. Do not mulch...
Parts Catalog - Page 5
...Amp Meter/Choke
34 925-04227B
Key Switch Module
35 925-1745A
Key
36 726-0230†
Cable Tie
37 751-0659D
Fuel Tank, 2 Gallons
751-10782
Fuel Tank, 1.36 Gallon, CARB...Tank Mnt.
NOT all parts listed above and pictured on the previous page are standard equipment. 7 K Style (Troy-Bilt) Hood
Ref. RH
8
731-05078C
Dash Collar Assembly
9
731-06194A
Hood Scoop
10 738-04091A
Shoulder ...
Parts Catalog - Page 12
Frame and PTO Lift
51 52
53
18
46
24
41 14
27
18
34
35
31
40 36
30
A 19
33
22
26 49
B A
1 7
11 C
33
9
5
17 20
B
6 11 10
3
2 13
8
16 20
23
17 26
15
49
25
22
29
20
28
21
25
22
C
3
12
42 8
B
39
2
43
46" Deck Lift
48
4 33 33 1
38
18
37
32
3
11
A 45
2
44
11
50
14
39
50
3 2
47 39
14
Parts Catalog - Page 13
...1.64 Grip, Handle, 3/8 Spring, Extension Washer, Lock, 7/16 Washer, Flat, .450 x 1.250 x .164 Bolt, Shldr. .500 x .270 3/8-16 Bearing, PTO Cable, Deck Engagement Spacer, 1.010 x 1.400 x .825, 42" Deck Engine Pulley Spring, Torsion 46" Deck Grip, Handle, 5/8 Battery, 155 CCA Deck Handle, Lift...Screw, #10-32 x .500
27 783-04548C-0637 Seat Bracket, Frame
Ref.
Frame and PTO Lift
Ref. Part No.
Similar Questions
Troy Built Riding Mower Turn Key And It Clicks Starter Motor Not Seized ?do
Mower tb30 b Turn key and clicks starter not siezed
Mower tb30 b Turn key and clicks starter not siezed
(Posted by rusthumphrey 11 months ago)
Need New Motor Engine For Troy Bitl Riding Lawn Mower 15.5
(Posted by janicesutton60 2 years ago)
Why Would A Troy Built Mower Pop And Emit Black Smoke?
(Posted by Lbaily7755 3 years ago)
Where To Find Diagram To How Pto Cable Runs. Putting In New One.
how to run pto cable
how to run pto cable
(Posted by Anonymous-159748 7 years ago)
Lawn Mower
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
(Posted by sgilbert491974 9 years ago)