Troy-Bilt CS 4325 Support Question
Troy-Bilt CS 4325 Support Question
Find answers below for this question about Troy-Bilt CS 4325.Need a Troy-Bilt CS 4325 manual? We have 1 online manual for this item!
Current Answers
Related Troy-Bilt CS 4325 Manual Pages
Operation Manual - Page 1
... OPERATE THIS MACHINE.
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Model Series CS4265 Shown
Chipper Shredder -
Operation Manual - Page 2
... applicable to the engine manufacturer's Owner's/Operator's Manual, packed separately with the machine, its features and operation. Table of product specifications for purchasing a Troy-Bilt Chipper Shredder. Box 361131 • Cleveland, OH • 44136-0019
2 It instructs you for various models. Please be found at all times. All information in this...
Operation Manual - Page 3
... result in serious injury or death. Thrown objects which ricochet can amputate fingers, hands, and feet.
8. Loose fitting clothes or jewelry can result in the chipper chute.
4. Never attempt to unclog either the feed intake or discharge opening . Wear sturdy, rough-soled work gloves when feeding material in serious injury. Be...
Operation Manual - Page 4
...is spilled on yourself or your face and body back and to the side of the chipper chute while feeding material into the machine to the machine.
4. Never tamper with the ...through the shredder hopper, use your vehicle before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are explosive. g.
Repair or replace any fuel soaked debris. This can ...
Operation Manual - Page 7
...the engine is extremely flammable and the vapors are completely covered. 3.
Gently pivot the chipper chute down until the engine has been allowed to the operator or bystanders. Position the...manual for at least two minutes after running or until it downward, proceed as follows:
1. Chipper Chute (Model Series CS4325 Only)
For shipping reasons, the unit is crated with engine running...
Operation Manual - Page 8
... operating position before starting the engine.
It is located on the chipper chute support.
Controls and Features
Hopper Handle
Chipper Chute
Recoil Starter
4
Spring Latch
Chute Deflector
Lock Rod
Model Series CS4325 Shown
Chipper Chute
Branches up to release or lock the chipper chute in diameter may be placed into the hopper for the location...
Operation Manual - Page 9
... unit for the correct starting instructions may not. Repeat the previous steps until the engine is completely normal and does NOT indicate a malfunction of any chipper shredder can damage your Engine Operator's Manual packed with a rapid, continuous, full arm stroke. Stopping Engine
1. Figure 5-2 NOTE: See your eyes severely. Starting Engine
IMPORTANT...
Operation Manual - Page 10
... this manual.
Twigs longer than two (2) inches (Model Series CS4265) or three (3) inches (model series CS4325) into the impeller. IMPORTANT: Never feed branches with sharp chipper blades.
IMPORTANT: Never place branches with debris during operation, proceed as tomato vines until they are thoroughly dried out. Grasp the handle with both hands firmly on...
Operation Manual - Page 11
... make sure these are tight. NOTE: Cleaning with light oil once a season.
3. Lubricate the chipper chute hinge a with a cloth or brush. To service the air cleaner, refer to operator abuse... season. To receive full value from muffler area.
11 Equipment Care
• Clean the chipper shredder thoroughly after each season.
• Periodically check all grass, dirt, and combustible debris ...
Operation Manual - Page 12
...removed earlier.
C
A B
Figure 6-1
12
Section 6- WARNING: The impeller's shredder blade and chipper blades are sharp. WARNING: The muffler and surrounding area will be pivoted upward so that the... the clevis pin which extends through the housing and shredder screen. See Figure 6-1C. chipper shredder has come to the chute deflector, if desired.
2. Remove the hairpin clip from...
Operation Manual - Page 13
... blade is visible through the impeller housing opening.
6. C
B
A
Model Series CS 4325 Shown
Figure 7-1
4. Remove the chipper chute by removing the internal hex screws,
Figure 7-2
lock washers and hex nuts ... a replacement blade (Part No. 742-0544) with the sharp edge outward (toward the chipper chute). Follow the original angle of
the impeller.
Remove the two flange nuts (and hex...
Operation Manual - Page 14
...correct engine storage instructions.
Refer to completely free shredder blade. See Figure 7-3A. Make certain each cutting edge receives an equal amount of engine and equipment.
See Figure 7-3B. Remove metal from the ...store in a clean, dry area. When storing the chipper shredder in an unventilated or metal storage shed, care should be taken to prevent an unbalanced blade.
Operation Manual - Page 15
... at full throttle. 2. Discharge area clogged.
2. Vacuum bag is not fully
depressed.
1. Chipper blade dull.
1. Connect wire to engine manual.
1. See authorized service dealer.
1. Choke ...stale fuel.
4. Loose parts or damaged impeller.
1. Refer to engine manual. 7. Replace chipper blade or see your authorized
service dealer.
15 Engine oil level low. 2. Dirty air cleaner...
Operation Manual - Page 16
Replacement Parts
Component
9
Part Number and Description
942-04050
Shredder Blade
942-0544B
Chipper Blade
719-04308
Flail Blade (3 total)
634-04627
10 x 4.0 Pneumatic Wheel with Bearings
Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (...
Operation Manual - Page 18
... wear parts include, but are warranted to be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for use , neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of Purchase to you may also have a separate...
Similar Questions
How Do I Change Cutting Head On A Troybilt Tb625ec?
I can't figure out how to remove the old cutting head.
I can't figure out how to remove the old cutting head.
(Posted by dougclapp24 7 years ago)
Tb32ec Cutting Head
how do you remove the cutting head on Tb32ec weed eater
how do you remove the cutting head on Tb32ec weed eater
(Posted by Kclaypool 9 years ago)
Troy Cs 4325 Oil Change Procedure
How do I change the oil in my chipper shredder
How do I change the oil in my chipper shredder
(Posted by gbaker1951 9 years ago)
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
How To Remove Cutting Head From Tb525 Ec Trimmer
(Posted by godez 10 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)