Toro LD6 Support Question
Toro LD6 Support Question
Find answers below for this question about Toro LD6 - CO M/R IRRIGATION 6 Zone Controller Timer.Need a Toro LD6 manual? We have 1 online manual for this item!
Question posted by horse7676 on July 30th, 2012
Ld4 Valve Controller
No display. Power is OK (24VAC)
Current Answers
Related Toro LD6 Manual Pages
Operation Manual - Page 2
... you have selected in the sample watering plan shown, program A has two start times for each selected valve in sequence, starting with the lowest valve number. I, Introduction: What is designed to operate up to the highest valve number. The LD4 is a Watering Cycle? Each can be set to a program, in sequence, from the lowest...
Operation Manual - Page 3
... lead you to enter data for applications such as drip. (The valve is off . Guided Programming (Optional)
In guided programming, the controller display prompts you through five easy steps. This will flash "OK". Use the 4 button to two start times. (Two start time(s). PROGRAM Ar o B - You may select particular days of time that each...
Operation Manual - Page 4
... to run for how long and on the button longer than 3 seconds, causes rapid change the hour and minute time shown on the display. (Continuous pressure on which valve to the correct day.
5. Return the dial to set the month. Note: Programs A and B II Each program is automatically indicated by pressing the...
Operation Manual - Page 5
... retained). You may set the start times turned off, then that program is Off. (All other program to the OFF position. The display will be no watering with that valve, and will water. 1.
Select program A or B.
3. Repeat steps 4 and 5 for that program. Set the dial to four hours. /
Canceling a Program Start Time...
Operation Manual - Page 6
... of a leap year, are always treated as ON. button to your choice.
2. The controller displays currently programmed day information. The previously selected days of the week, odd days, or even... under your system. Selecting Specific Days of the week to turn watering off and the next valve opens. Repeat steps 1 and 2 until all selected programs and start times.
button to select...
Operation Manual - Page 7
.... For example, this can be used to begin the manual watering cycle. Select program A or B.
3. Display shows MANUAL PROGRAM CYCLE A, program A or B, valve number A, and counts down the remaining run time for each active valve.
1. To return controller to normal automatic operation, simply return dial to RUN position if automatic operation is desired. Always...
Operation Manual - Page 8
... The controller must be mounted at least 15 feet away from your pump start one or more valves watering sequentially for a selected period of time for the set time with the display at...valve 1 A will water sequentially for valve 1 to water or skip to the next desired valve by pressing the 4 key to start relay and pump.
Mounting the Con troller
1. From this feature to skip any power...
Operation Manual - Page 9
... mounted and ALL valves have more than one from the back yard. The single lead wire is designed as a memory retention feature only. The display will illuminate under battery power. Turn dial to the two screws marked AC. Connect the transformer wires to illuminate display. All commons get connected to the controller. If a number of...
Operation Manual - Page 10
...MUSS A C C O M O D A T E PUMP'S ELECTRICAL RATING
Connecting a Pump Start Relay
The controller must be used.
See your pump, (i.e.
PUMP POWER
W A R N I N G : If a pump start is installed you must be rated for use with... should be connected to the master valve). one Lawn Genie, Hardie, or Richdel valve), may be connected to the master valve output terminal marked MV and the common...
Operation Manual - Page 11
... damage the controller. Hardie Irrigation will replace, free of charge, the part, or parts found to its customers that this controller. Power Failures
Due to the possibility of purchase required. The default is factory set to the pump start or master valve installed, you do not have a pump start terminals. Note: This controller is common in...
Similar Questions
Screen Said Fuse, What Is The Procedure
screen said... fuse. what is procedure
screen said... fuse. what is procedure
(Posted by pacificatm 2 years ago)
My 51592 #270040795 Leaf Blower Stopped Working. If I Press The Post Of The
CPU2113 micro-swith on the bottom of the motor housing the motor will start, but turn off when I sto...
CPU2113 micro-swith on the bottom of the motor housing the motor will start, but turn off when I sto...
(Posted by darkh 11 years ago)
How Do I Set My Watering Zones
i lost my manual and need to change the time of day, the days and the run time of each zone. How do ...
i lost my manual and need to change the time of day, the days and the run time of each zone. How do ...
(Posted by Rrmcm 11 years ago)
All The Wires Are Disconnected From The Valves, How Do I Reconnect Them.
(Posted by manuel72mr2 12 years ago)
The Rpm Switch Turns Past Max. And Turns Off.
It will not continuously run, unless I hold down on the switch. Is there a stop that is broken? Is i...
It will not continuously run, unless I hold down on the switch. Is there a stop that is broken? Is i...
(Posted by daviswayne2001 12 years ago)