TP-Link MC210CS Support Question
TP-Link MC210CS Support Question
Find answers below for this question about TP-Link MC210CS.Need a TP-Link MC210CS manual? We have 1 online manual for this item!
Question posted by mataniagila on November 8th, 2012
Connection On No Fx Device Is It Possible
I got the a TP Link F.O Media converter model: MC210CS after a review and reading manuals guide the unit is working using my LAN base (Catalyst 2960 series) the problem is I have only one and already used with STP module.
How do I connect this unit using my existing catalyst. there is 8 lan ports but when I connect the converter the RX and Link are not blinking.
Current Answers
Related TP-Link MC210CS Manual Pages
MC200CM User Guide - Page 2
No part of the specifications may be reproduced in any form or by any means or used to change without permission from TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are subject to make any derivative such as translation, transformation...
MC200CM User Guide - Page 3
Introduction 1 2. Installation Guides 5 4.1 Gigabit Ethernet Media Converter 5 4.2 Configuration 7 4.3 Installation Procedure 8 4.4 Install Media Converter into MC1400 9 5. Appendix: Specifications 11
i Troubleshooting 10 6. Appearance Indication 3
3.1 LED Indicators 3 3.2 Switch 4 4. Features 2 3. CONTENTS Package Contents 1 1.
MC200CM User Guide - Page 4
... Media Converters. The FX port of the Gigabit Ethernet network
Rear Panel
Front Panel
MC200CM&MC210CS 1 The converter mediates between a 1000Base-TX segment and a 1000Base-X segment. It is what you have is primarily designed for larger bandwidth, and higher speed demanding workgroups that require expansion of MC220L supports hot-swappable.
Package Contents
Before starting using...
MC200CM User Guide - Page 5
Please check the table in Full-Duplex mode for both TX port and FX port. ¾ Support auto MDI/MDIX for single-mode fiber. Features
¾ Comply...MC220L Note:
This media convertor can also be powered by 5VDC Adapter.
2. Please check the table in page 3 for the accurate connector of each model. ¾ Work at 1000Mbps in page 3 for the accurate transmission distance of each model. ¾ Easy...
MC200CM User Guide - Page 6
... MC210CS MC220L
Interface
RJ45--SC RJ45--SC RJ45--LC
Transmission Distance
0.55km(50/125um) 0.22km(62.5/125um) 15km
0.55km/10km
Transmission Media
Multi-mode Fiber,TP Single-mode Fiber,TP
Multi/single-mode
Output Center Wavelength
850nm
1310nm
850nm/1310 nm
SC fiber connector and LC fiber connector
3.
Appearance Indication
3.1 LED Indicators
This converter has...
MC200CM User Guide - Page 7
... User Guide Manual stands for TP Port. There's no valid link for TP Port. Note:
The TP port mentioned in FORCE mode.
4 PWR
RX
LINK
LINK
FX TP
Name Status Indication
On Power on your network. When you take a look at these indicators, you will know what's happening on PWR
Off Power off
On FX LINK
Off
There's a valid link for FX Port.
The converter...
MC200CM User Guide - Page 8
... FORCE mode. Then the change would take effect.
4. Negotiation mode. Installation Guides
4.1 Gigabit Ethernet Media Converter:
¾ The SC fiber connector of MC200CM transmits/receives data by 850nm short wave laser on multi-mode fiber.
¾ The SC fiber connector of MC210CS transmits/receives data by 1310nm short wave laser on single-mode fiber...
MC200CM User Guide - Page 9
MC220L can be plugged in with the same SFP module could cooperate. Plug the SFP module into MC220L
Transmits and receives data between two MC220L Note: Two MC220L with two kinds of SFP modules, single-mode or multi-mode. Note: Either two MC200CM or two MC210CS could cooperate.
6
MC200CM User Guide - Page 10
... two converters back to back between MC220L and MC200CM/MC210CS
Note:
MC220L could be LC-SC fiber.
MC220L connect with MC200CM
MC210CS
Transmission Media
SFP module
850nm, Multi-mode
1310nm, Single-mode
4.2 Configuration
In order to the table below) And the connection fiber must be connected to MC200CM or MC210CS, however, the SFP module in MC220L must use the...
MC200CM User Guide - Page 11
...
Use a fiber cable to connect two converters, or connect a converter with another MC200CM/MC210CS. 2. Connection of a Converter and a 1000Base-TX Device (HUB or
Switch): Make sure that the length of the Cat.5 twisted pair cable (Category-5) between the 1000Base-TX device and the converter is to place one MC220L with a 1000Base-FX Device. 1. Note: For the correct connection between 2 Media...
MC200CM User Guide - Page 12
Connection of a Converter and a 1000Base-FX Device.
3. FX Device: Use a SC fiber cable to lock it tightly as follows.
1. Turn on the power.
4.4 Install Media Converter into MC1400
Tweak out the two screws located on the switch power and you need in the slot of the chassis, and use them to install the retainer as follows.
2. 2. Turn on either side of...
MC200CM User Guide - Page 13
... make sure that the FX port is connected correctly as the boxlike Media Converter of outlying end. And the receiving port (RX) of outlying end.
10 Then you install or use this product, please try to solve the problem according to the transmitting port (TX) of local end is connected correctly or not. 2. LINK LED (TP port) is off...
MC200CM User Guide - Page 14
...℃ Storage: -40℃~70℃ Operation: 10%~90% non-condensing Storage: 5%~90% non-condensing
Standards and Protocols Media Interface Max. 6. Appendix: Specifications
Standards and Protocols Media Interface Max. Distance Power Temperature
Humidity
MC210CS IEEE802.3ab, IEEE 802.3z, IEEE 802.3x SC, RJ45 Cat.5: 100m Single-mode Fiber: 15km External Power Adapter...
MC200CM User Guide - Page 15
Standards and Protocols Media Interface Max. Distance Power Temperature
Humidity
MC220L IEEE802.3ab, IEEE 802.3z, IEEE 802.3x LC, RJ45 Cat.5: 100m Multi/Single-mode Fiber: 0.55km/10km External Power Adapter Operation: 0℃~40℃ Storage: -40℃~70℃ Operation: 10%~90% non-condensing Storage: 5%~90% non-condensing
12
Similar Questions
Tp-link Mc100cm Not Connecting
Rebooted both ends of the converter, cant seem to connect from computer to change message on message...
Rebooted both ends of the converter, cant seem to connect from computer to change message on message...
(Posted by kodyperin 9 years ago)
Can't Connect Second Device On Tp Link Td-w8901g
(Posted by jositwin 10 years ago)
Fx Indicator
Hello, I have a Tp-Link MC100CM Media Conerter. all the led are on except for the FX link and wh...
Hello, I have a Tp-Link MC100CM Media Conerter. all the led are on except for the FX link and wh...
(Posted by edanlloyd 10 years ago)
Tp-link Mc210cs
how to connect to building thru fiber optic, by using theTP-Link MC210CS, and how to put the cable i...
how to connect to building thru fiber optic, by using theTP-Link MC210CS, and how to put the cable i...
(Posted by josephmikhael 12 years ago)
How To Use Tp Link Adapter To My Laptop Connect In Broadban 100mbps
how to use TP link adapter to my laptop connect in broadban 100mbps
how to use TP link adapter to my laptop connect in broadban 100mbps
(Posted by loisaflores08 13 years ago)