Stihl HS 56 C-E Support Question
Stihl HS 56 C-E Support Question
Find answers below for this question about Stihl HS 56 C-E.Need a Stihl HS 56 C-E manual? We have 1 online manual for this item!
Question posted by carlosprice767 on April 8th, 2016
What Will Keep Your Still Hs 56c From Taken Gas After It Starts
The person who posted this question about this Stihl product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Stihl HS 56 C-E Manual Pages
Instruction Manual - Page 1
STIHL HS 46, 56
{
Instruction Manual Notice d'emploi
Instruction Manual - Page 3
...
2
Safety Precautions and Working
Techniques
2
Using the Unit
7
Fuel
8
Fueling
9
Starting / Stopping the Engine
13
Operating Instructions
15
Cleaning the Air Filter
15
Engine Management
...25
Maintenance and Repairs
26
STIHL Limited Emission Control
Warranty Statement
26
{
HS 46, HS 46 C, HS 56 C
English
Dear Customer, Thank you have any queries concerning your satisfaction...
Instruction Manual - Page 4
... use a power tool.
It is responsible for avoiding injury to third parties or damage to their property. Do not lend or rent your machine. HS 46, HS 46 C, HS 56 C Nonobservance of the instruction manual may modify the design, engineering and appearance of our products periodically.
Fuel tank; fuel mixture of gasoline and engine...
Instruction Manual - Page 5
... muffs. Clothing and Equipment
Wear proper protective clothing and equipment. Wear snug-fitting clothing, an overall and jacket combination, do not smoke.
0008BA024 KN
HS 46, HS 46 C, HS 56 C
3 STIHL recommends the use of movement.
Keep clear of the power tool.
The solid jet of water may interfere with pacemakers consult their physician...
Instruction Manual - Page 6
... run for damage.
- a loose boot may spill and cause a fire. for fuel leakage. Starting the engine
Start the engine at least 3 meters from oil and dirt -
Check idle speed setting: The cutting ...both hands on your fingers and thumbs around the handles.
4
HS 46, HS 46 C, HS 56 C
Holding and Controlling the Power Tool
Always hold the power tool firmly with STIHL resin solvent (...
Instruction Manual - Page 7
...possibilities, these symptoms may be caused by an excessively high concentration of the hedge before starting work on an insecure support
-
Left-handers
Left hand on the control handle and ...Never run for obstacles: Roots, tree stumps or holes which could cause you cannot see. HS 46, HS 46 C, HS 56 C
5 Work calmly and carefully -
Never work . Check that you to avoid tiredness or...
Instruction Manual - Page 8
... position -
Check condition and tightness, look for this causes overheating and damage to important components (e.g. Work breaks
The period of the above
6
HS 46, HS 46 C, HS 56 C see also "Before Starting". Do not continue operating your power tool.
The dust that it is idling. Before leaving the power tool unattended: Shut off the engine...
Instruction Manual - Page 9
... rules and regulations for a component which has not been serviced or maintained properly or if nonapproved replacement parts were used, STIHL may be composted! HS 46, HS 46 C, HS 56 C
7 Have all other people's rest periods. STIHL dealers are regularly given the opportunity to attend training courses and are specifically designed to hearing, do...
Instruction Manual - Page 10
... gasoline and highquality two-stroke air-cooled engine oil. This could cause running behaviour of the engine and increase the risk of lean seizure.
8
HS 46, HS 46 C, HS 56 C
English Working Technique Vertical cut
Hold the cutter bar at an angle of 0° to 10° as well. lower the nose of the...
Instruction Manual - Page 11
... only.
The canister should be kept tightly closed in order to 25% (E25).
N Position the machine so that no dirt falls into the tank.
HS 46, HS 46 C, HS 56 C
9
Tank cap markings
Tank caps and fuel tanks may be equipped with a tank cap and fuel tank with or without symbols.
When mixing, pour...
Instruction Manual - Page 15
..., move the Master Control lever to the normal run position F -
0008BA008 KN
Starting / Stopping the Engine
Positions and Functions of STOP or † -
The Master... (2) and Master Control lever.
0008BA009 KN
HS 46, HS 46 C, HS 56 C
13 To select the starting throttle position n. N Set the Master Control lever to start a warm engine.
this position is switched on...
Instruction Manual - Page 16
... Master Control lever springs back to the normal run position F. Version without Easy2Start N Pull the starter grip slowly until the engine runs.
14
HS 46, HS 46 C, HS 56 C
After a cold start )
1
3
2
N Depress the throttle trigger lockout (1) and the throttle trigger (2) at the same time - The cutting attachment must not rotate when the engine is...
Instruction Manual - Page 17
...tank and keep the machine in the engine are correct. N Fit the filter element (3).
N Start the engine. This avoids unnecessary high loads during the break-in period, the frictional resistances in...long period of full throttle operation, allow the engine to cool down firmly.
0008BA014 KN
HS 46, HS 46 C, HS 56 C
15 After Finishing Work
Storing for a short period: Wait for the first three ...
Instruction Manual - Page 18
...is only possible to run when engine is idling, have your servicing dealer.
16
HS 46, HS 46 C, HS 56 C N Check the air filter and clean or replace if necessary. N Turn the... or port timing) without the addition of the fundamental engine parameters and components (e.g.
N Start and warm up the engine. Adjusting the Carburetor
General Information
The carburetor comes from the factory...
Instruction Manual - Page 20
...flap (1) with a detachable adapter nut (1), screw the adapter onto the thread and tighten it down firmly to start or runs poorly at idle speed, first check the spark plug.
N Tighten down on power, difficult to...the bottom, tabs (arrows) must snap into position.
0008BA019 KN
18
HS 46, HS 46 C, HS 56 C N Unscrew the spark plug.
N Press the spark plug boot firmly
onto the spark plug.
Instruction Manual - Page 21
...
Use STIHL gear lubricant for hedgetrimmers (special accessory) to snap back, guide it breaks completely.
HS 46, HS 46 C, HS 56 C
19 N Remove the retaining plate (2) and gearbox cover (3).
0008BA020 KN
Do not completely ...
5 4
N Squeeze grease into the housing slowly -
see chapter on "Starting / Stopping the Engine."
STIHL recommends that it is flush with the cutting blades...
Instruction Manual - Page 23
...not adjusting screws)
Retighten
Antivibration elements
Visual inspection
X
Have replaced by dealer1)
before starting work after finishing work area, etc.), shorten the specified intervals accordingly. If your ...
X
X
X
X
X
X
X
X
X
X X
X
X
X
X
X
X
X
X
HS 46, HS 46 C, HS 56 C
21
Maintenance and Care
The following intervals apply to normal operating conditions only.
Instruction Manual - Page 24
... with STIHL gear lubricant if necessary
Safety labels
Replace
1) STIHL recommends a STIHL servicing dealer. 2) not in all versions, market-specific
before starting work after each refueling stop weekly monthly every 12 months if problem if damaged if required
X X
X
22
HS 46, HS 46 C, HS 56 C English
The following intervals apply to normal operating conditions only.
Instruction Manual - Page 26
...Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for starting the engine.
14 Blade Scabbard Covers cutting blades when hedge trimmer is not in case....
15 Cutting Blades (HS 46) Steel blades for cutting hedges and shrubs.
16 Cutting Blades (HS 46 C) Steel blades for cutting hedges and shrubs.
17 Cutting Blades (HS 56 C) Steel blades for cutting...
Instruction Manual - Page 29
... of fuel and oil may require shorter maintenance intervals.
The following list specifically defines the emission-related warranted parts:
- Choke (Cold Start Enrichment System)
- Fuel Tank
- Clamps
- HS 46, HS 46 C, HS 56 C
27 N6A 4L6
Coverage by STIHL Limited at an authorized STIHL servicing dealer. STIHL Limited also warrants to the initial purchaser and...
Similar Questions
Need Illustrated Parts Breakdown Manual For This Hedge Trimmer. Stihl Hs 56
need Illustrated parts breakdown manual for Stihl HS 56
need Illustrated parts breakdown manual for Stihl HS 56
(Posted by charlesbakes 5 years ago)
Part No For Stihl Km90r On/of Switch
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
(Posted by johnnash222 8 years ago)
Stihl Hs 54c Gas Powered Hedge Trimmers Runs Great Until You Turn It Sideways
My STIHL HS- 56 -C starts and runs like a champ but when you tip it sideways or nose down it will st...
My STIHL HS- 56 -C starts and runs like a champ but when you tip it sideways or nose down it will st...
(Posted by Travintrxas 8 years ago)