Stihl FS 90 R Support Question
Stihl FS 90 R Support Question
Find answers below for this question about Stihl FS 90 R.Need a Stihl FS 90 R manual? We have 2 online manuals for this item!
Question posted by Bphillips912 on July 17th, 2014
What Size Is The Nut Holding The Carburetor In Place
The person who posted this question about this Stihl product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Stihl FS 90 R Manual Pages
Product Instruction Manual - Page 3
...33
Operating Instructions
36
Cleaning the Air Filter
36
Engine Management
36
Adjusting the Carburetor
37
Spark Arresting Screen in Muffler 38
Spark Plug
39
Lubricating the Gearbox
... Statement
STIHL Incorporated California Exhaust and Evaporative Emissions Control Warranty Statement
Trademarks
{
FS 90, FS 90 R
English
48 Allow only persons who fully understand
49
this manual. M40...
Product Instruction Manual - Page 10
...! As can be properly balanced as possible. Place the power tool on the deflector (A) and ... attachment. Adjust carrying harness and hand grip to change your size before using the power tool. The machine should be seen...attachment must be better prepared in operation. Inspect for loose parts (nuts, screws, etc.) and for the type of Cutting Attachment, Deflector...FS 90, FS 90 R
Product Instruction Manual - Page 11
... engine to slow down to idle.
English During Operation Holding and Controlling the Power Tool
Always hold the unit firmly with both hands on how to adjust idle speed, see appropriate chapter of moisture, pitch, oil, fuel mix or grease.
002BA054 KN
002BA055 KN
FS 90, FS 90 R
9
Warning!
Important Adjustments
Warning!
Warning! At correct idle...
Product Instruction Manual - Page 12
...carbon monoxide, that are known to 0 or STOP.
10
FS 90, FS 90 R Warning! Control dust at all times. When the inhalation... Never touch a moving cutting attachment with a smaller particle size, may cause respiratory or other reproductive harm. Warning!
Warning... For better footing, clear away scrub and cuttings. Never hold the cutting attachment above waist height. carbon monoxide) may ...
Product Instruction Manual - Page 15
...in your instruction manual).
002BA354 KN 002BA177 KN
If the lawn edges are missing or worn - This causes the clutch...or bystanders. Such damage could, among other material in place of wire could result in linelimiting blade will automatically ... of severe or fatal injury from breakage of the PolyCut.
FS 90, FS 90 R
13 STIHL SuperCut mowing head
Fresh line is important to...
Product Instruction Manual - Page 18
... loose connection between the spark plug and the ignition wire connector in serious or fatal injuries.
16
FS 90, FS 90 R In order to come off and result in the boot may cause serious or fatal injury. Use...missing or damaged. To reduce the risk of loss of the proper size. (Note: If the terminal has a detachable SAE adapter nut, it and the ignition lead are always clean and in your STIHL ...
Product Instruction Manual - Page 19
... power tool in the instruction manual. English
FS 90, FS 90 R
17 The solid jet of water may damage parts of children. Before storing for longer than a few days, always empty the fuel tank.
Do not clean your machine with a pressure washer. Tighten all nuts, bolts and screws, except the carburetor adjustment screws, after each use.
Product Instruction Manual - Page 23
hold both clamps together
N Insert the tommy screw with the washer on it through both clamps as far as it will go and then screw it in - check distance (A)
N Tighten tommy screw
N Unscrew the bolt (9) -
do not tighten it in the lower clamp! FS 90, FS 90...(1) so that it will go - the nut (10) remains in the control handle (11... Place the upper clamp on top and hold all parts ...
Product Instruction Manual - Page 25
...9 4
10
N Secure the loop handle (4) about 20cm/8in (A) forward of the control handle (9). FS 90, FS 90 R
23 N Place the clamp (6) in position
as stop. The sleeve (10) (not fitted on the screws (8) and... control handle. N Line up the holes.
Fit the square nuts (1) and screw them both on the drive tube (5). lock the nuts if necessary. N Go to "Securing the loop handle".
002BA099...
Product Instruction Manual - Page 26
...is fully assembled - N Squeeze the two ends of the clamp together and hold in the normal operating position. English
Adjusting the Throttle Cable
Some machine versions ... Deflector for correct operation in the same way.
N Place the deflector on the control handle.
STOP
2
1
N Press down firmly.
002BA380 KN
24
FS 90, FS 90 R N Place the clamp (1) against the drive tube with a throttle...
Product Instruction Manual - Page 28
... blocks the shaft.
N Use the combination wrench (6) -
in the hole (8) in place of a mowing head, you will need the following additional parts: Nut (3), rider plate (4) and thrust washer (5) (special accessories). STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2,
26
FS 90, FS 90 R
N Block the shaft - to "Mounting the mowing head".
comes standard with machine...
Product Instruction Manual - Page 29
...limit stop for grass cutting blades 230-4 (1), 230-8 (2) or the brush knife (3) -
FS 90, FS 90 R
27 thus repeated tapping in the mowing head information sheet. Always switch off the engine... fed out automatically if the mowing line is indicated by hand -
STIHL AutoCut
N Hold the mowing head parallel above the surface of mowing line is only fed out if ...in . (3 cm) of the lawn -
Product Instruction Manual - Page 30
.... Collar (see arrow) must be run on a fuel mixture of gasoline and engine oil. If the mounting nut turns too freely, fit a new one.
28
FS 90, FS 90 R English
Removing the metal cutting attachment
N Block the drive shaft. N Place the cutting attachment (6) on the 4-stroke principle. It operates otherwise on the thrust plate (7). N Take the...
Product Instruction Manual - Page 31
...adjustment, have your STIHL dealer check your vehicle and place the container on the ground before filling.
Use only...recommends that are for a few days work, not to readjust the carburetor if you use only in turn, increases the risk of piston ...that gets into the container first, and then add gasoline. FS 90, FS 90 R
29 The chemical composition of highquality gasoline and two-stroke...
Product Instruction Manual - Page 36
...drive tube.
34
FS 90, FS 90 R
normal run position - even if the bulb is switched on the stop symbol (h) to START and hold them in that position. N Hold the unit with fuel....
N Now release the throttle trigger, slide control and trigger lockout in the direction of slide control
4 STOP-0 - To stop symbol and arrow.
N Place...
Product Instruction Manual - Page 37
N Hold the starter grip with fuel... the spark plug - N Refit the spark plug - even if the bulb is flooded. FS 90, FS 90 R
35 N Pull the starter grip slowly until you did not turn the choke knob to... the throttle trigger.
see chapter on the stop symbol (h) to fire.
Make sure the carburetor is idling. Your machine is cold. Shut off the engine.
N Dry the spark plug...
Product Instruction Manual - Page 38
...break-in a dry place, well away from sources...the engine are controlled by the flow of any major hardware.
36
FS 90, FS 90 R English
Operating Instructions
Cleaning the Air Filter
Engine Management
During break-in... choke knob to 15 tank fillings.
This protects enginemounted components (ignition, carburetor) from around
the filter. Do not wash. N Replace damaged parts. After ...
Product Instruction Manual - Page 41
... resistor type spark plugs of fire and burn injury, use only spark plugs authorized by STIHL. FS 90, FS 90 R
39
These factors cause deposits to form on power, difficult to STOP-0.
1
N Pull ...spark plug boot (1) snugly onto spark plug terminal (2) of the proper size. (Note: If terminal has detachable SAE adapter nut, it down on the insulator nose which have caused fouling of spark ...
Product Instruction Manual - Page 44
... local environmental requirements. N Run the engine until the carburetor is overtensioned and could break. N Thoroughly clean the machine - N Hold the rotor steady. The starter grip must still be ... helps prevent the carburetor diaphragms sticking together. pay special attention to rotate the rotor another half turn of children and other unauthorized persons.
42
FS 90, FS 90 R N When the...
Product Instruction Manual - Page 46
... dealer 1) have them replaced by a specialist dealer 1)
Fuel tank
clean
Carburetor
check idle adjustment, cutting attachment must be shortened accordingly when working for longer...maintenance intervals apply in muffler
clean or replace
All accessible screws, nuts and bolts (not adjusting screws)
retighten
44
before starting work at...X
X
X
X X
X X
X
X
X
X
X
FS 90, FS 90 R
Similar Questions
What Tool Is Needed To Adjust The High And Low Speed On The Fs 90r String Trimm
what tool is needed to adjust the high and low speeds on the carburetor of the stihl fs 90r string t...
what tool is needed to adjust the high and low speeds on the carburetor of the stihl fs 90r string t...
(Posted by ckneejoint 8 months ago)
What Size Nut Hold The Carburetor Cover On A Stihl Hs 81t. 8mm Doesn't Fit?
(Posted by nixonlawn 2 years ago)
Primer Bulb For Fs 90r
I replaced the primer bulb but in doing so, the screen beneath came off. I replaced it not sure whic...
I replaced the primer bulb but in doing so, the screen beneath came off. I replaced it not sure whic...
(Posted by rwdredraider 7 years ago)
Part No For Stihl Km90r On/of Switch
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
(Posted by johnnash222 7 years ago)