Sony RM-AV2500 Support Question
Sony RM-AV2500 Support Question
Find answers below for this question about Sony RM-AV2500 - Integrated Remote Commander.Need a Sony RM-AV2500 manual? We have 3 online manuals for this item!
Question posted by mjgraves on July 31st, 2015
Vizio Tv Code
Is there a code for vizio tv that can be used with RM-AV2500?
Current Answers
Answer #1: Posted by TechSupport101 on July 31st, 2015 6:47 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Related Sony RM-AV2500 Manual Pages
Operating Instructions (primary manual) - Page 1
3-267-590-12(1)
Integrated Remote Commander
Operating Instructions
RM-AV2500
© 2004 Sony Corporation
Operating Instructions (primary manual) - Page 3
...15). The display backlight allows operation even in one remote commander This Commander is useful to display the Power key for most major brands components including Sony. Features
The RM-AV2500 Remote Commander provides centralized control of all together, you need This Commander has a learning function, to learn remote control signals (infrared signals only) of non-Audio Visual components...
Operating Instructions (primary manual) - Page 4
...Remote Commander 13 To control the volume ...14 Notes on learning the signals of Controls 7
Basic Operations
Setting the Code for Preset Audio and Visual Components 8 Setting a component code 8 Checking if the code number works 10 Finding a component code...command of the selected component
(for SYSTEM CONTROL Buttons 35 Notes on operating your components 14
Using Non-Preset Remote Control...
Operating Instructions (primary manual) - Page 6
...open the battery compartment lid and insert four size AA (R6) batteries (not supplied). If the Commander does not operate properly, batteries might be erased. on the LCD touch panel. Note Do not ...leaking, remove the batteries when you plan not to use the Commander for a long period of the code numbers (page 8) and learned remote control signals (page 15) will last up the + and -
Operating Instructions (primary manual) - Page 10
... setup procedures using the learning function, you can program remote control signals to be displayed. The Commander turns on ...Commander is shown on the display. When the remote control signal is sent, is operating the other codes listed for details.
5 Press COMMANDER OFF. Note on the touch-key display When you set a component code number, only the keys that have "learned" a remote control...
Operating Instructions (primary manual) - Page 12
... 5.
When the remote control signal is sent, is set the code number.
Be sure to press the DISPLAY key after you press the DISPLAY key before the code number is shown on for VCR, DVD, SAT, CBL, AMP, and playback for Preset Audio and Visual Components (continued)
4 Aim the Commander at which code number is recommended...
Operating Instructions (primary manual) - Page 13
... code first (page 8).
2
3 1
2 Press the desired key in the
touch-key display. Note, however, that components and functions that do not support the remote control of keys and buttons for some components or functions.
buttons if necessary. See "Table of Preset Functions" (page 59) for operating the selected component are done using the
Commander, press COMMANDER...
Operating Instructions (primary manual) - Page 15
... whose signals are to
head with your component's remote control. It is useful if you make a memo of another remote control. Learning Function
To operate non-preset components or functions, use the learning function to change the signal of the Commander
1 Place the RM-AV2500 head to be learned.
You can also use the following "learning" procedure to "teach" any...
Operating Instructions (primary manual) - Page 16
... (continued)
The "C+ C- Example: When pressing the VOLUME + button
4 Press and hold down the button
on the left to "teach."
Using Non-Preset Remote Control Operations - To learn another component's remote control signal After positioning the two remote commanders as in Step 1 on page 15, press the corresponding Component Select button, and then follow Steps 3 and 4 on the...
Operating Instructions (primary manual) - Page 19
... the learning procedure.
•Be sure to keep holding down the button of the other remote control until you hear the confirmation beep.
•Use fresh batteries in both remote control units.
•Avoid learning in places under direct sunlight or a strong fluorescent light.
•The remote control detector area may interfere with the learning of the Commander.
Operating Instructions (primary manual) - Page 20
The learned contents are cleared. Using Non-Preset Remote Control Operations - Learning Function (continued)
To clear all signals learned for the component return to their original states before learning.
20 The keys for a specific component
3 Press COMMANDER OFF.
3
2
1
1 While pressing COMMANDER
OFF, press the corresponding Component Select button.
2 While pressing the LIGHT button,
...
Operating Instructions (primary manual) - Page 22
... by the learning procedure (page 15). Controlling the Volume of visual components (TV, VCR, CBL, SAT, and DVD) changes to the displayed component. The volume control setting of Visual Components Connected to an Audio System (continued)
1 While pressing COMMANDER
OFF, press VOLUME + and VOLUME -. To use that each remote control signal is transmitted, the corresponding key is...
Operating Instructions (primary manual) - Page 25
... been programmed in the series of commands of the final step.
By programming an often-used component's command as TV Poweron and input select may not accept
consecutive remote control signals. About the order of operation steps • Some of commands such as the final step, you can change the component code number (page 8) or program a new signal...
Operating Instructions (primary manual) - Page 27
... COMMANDER OFF
TV
CBL
SAT
DVR
VCR
M1
AMP
CD
MD
TAPE
DVD
M2
1
Continued 27 This is blocking them, some of the components did not operate correctly because of the above or for any other reason, always set all the components back to the states they were in before using the system control...
Operating Instructions (primary manual) - Page 32
... not be learned. Then whenever you always have another remote control signal by learning, clear the learned signal first (page 33).
32 Remote control of your amplifier to the CD button
1 Place the RM-AV2500 head to
head with your component
about 2 - 4 inches (5 - 10 cm) away
RM-AV2500
2 While pressing COMMANDER
OFF, press CHANNEL + and VOLUME +. Adding an Extra...
Operating Instructions (primary manual) - Page 33
... on the component's remote control (amplifier in this case, the System Control function or the Power-On function is resumed, and you can use the Power-On function.
33 In this example) until you hear a beep. (If you release the button before you want to clear. Try Steps 3 and 4 again.
5 Press COMMANDER OFF.
3 Press the...
Operating Instructions (primary manual) - Page 35
...Select button to
head with the remote control of your air-conditioner
about 2 - 4 inches (5 - 10 cm) away
RM-AV2500
2 While pressing COMMANDER
OFF, press CHANNEL + and VOLUME +. If you prefer having the SYSTEM CONTROL button as a "onetouch" button for SYSTEM CONTROL Buttons
In addition to their original System Control functions (page 22), SYSTEM CONTROL 1 - 9, A, B or C buttons can work as...
Operating Instructions (primary manual) - Page 36
... correctly.)
Note You can use them again.
If "NG" flashes on the display Learning did not succeed. "LEARN" display stops flashing and stays lit. To clear the learned remote control signal 1 While pressing COMMANDER OFF,
press CHANNEL + and VOLUME +. 2 While pressing the LIGHT button,
press the SYSTEM CONTROL button (1 - 9, A, B, or C). 3 Press COMMANDER OFF. The display for...
Operating Instructions (primary manual) - Page 37
...RM-AV2500. To transfer the all data of this Commander to program the remote control signals of the Commander
4
6 3
2
Continued 37
Transferring Data between Remote Commanders
...Commander as learned signals and component code settings, between this Commander, for example, the SYSTEM CONTROL C button).
If the Commander can operate only "ON" with one button and "OFF" with the Commander...
Operating Instructions (primary manual) - Page 56
... the Remote Commander has learned the correct signals. In this case, the volume cannot be preset. other than TV or AMP.
• When you teach signals of the main unit may not be controlled when you have assigned another component to the Commander, the response signal of an interactive signal exchange system remote control unit (supplied with a code...
Similar Questions
Is There A Replacement For Sony Clock Radio Remote Control Rm-cd543a?
Apparently, Sony is no longer making thismodelremote control. Can I buy another Sony model that will...
Apparently, Sony is no longer making thismodelremote control. Can I buy another Sony model that will...
(Posted by barrytaylor299 11 years ago)
How Do I Turn Off The Display On My Sony Tv Remote Control Rm-y168. Thanks
How do I turn off the display on my sony tv remote control RM-Y168. Thanks
How do I turn off the display on my sony tv remote control RM-Y168. Thanks
(Posted by mmesoros 11 years ago)
Manual For Sony Integrated Remote Commander, Rm-av2500
(Posted by emilylgunn 12 years ago)
Re: Sony Rm-av 2500 Integrated Remote
Can I print a manual for free for the above remote?
Can I print a manual for free for the above remote?
(Posted by kateyesuc 13 years ago)
What Are The Component Codes
in the manual for setting up the remote i am asked to enter component codes. what are thes and where...
in the manual for setting up the remote i am asked to enter component codes. what are thes and where...
(Posted by tanyamc1978 13 years ago)