Singer 8500Q MODERN QUILTER Support Question
Singer 8500Q MODERN QUILTER Support Question
Find answers below for this question about Singer 8500Q MODERN QUILTER.Need a Singer 8500Q MODERN QUILTER manual? We have 1 online manual for this item!
Question posted by Gmyles1 on December 31st, 2018
My Machine Gives A Error Code With The Top Thread Sensor And Will Only Stitch Fo
machine will only stitch one inch before it stops and gives error It has something to do with the top threading area sensorIs this repairable what do I do or who can fix it
Current Answers
Answer #1: Posted by waelsaidani1 on March 10th, 2019 3:33 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
This can be caused if the top thread tension is too tight, or if the bobbin thread is not in the bobbin case tension. Check that the upper thread is feeding freely without obstruction (like getting stuck behind the spool cap or getting caught on any rough spots o the thread spool itself). Make sure the bobbin is correctly seated in the bobbin case (bobbin holder), and check that the upper thread tension is not set too tightly.
Related Singer 8500Q MODERN QUILTER Manual Pages
Instruction Manual - Page 2
³,03257$176$)(7
Instruction Manual - Page 5
... area and feed dogs 68 - 69 Oiling inside the face cover 70 - 71 Special accessories 72 - 81 Helpful messages 82 - 83 Programming the memory 84 - 89
For European version
Sewing machine Dimensions: 567 mm × 240 mm × 317 mm Mass of operation switch panel 30 - 31
2. STARTING TO SEW Quick reference table of stitch...
Instruction Manual - Page 8
GETTING TO KNOW YOUR MACHINE
MACHINE IDENTIFICATION
2
1
1. Presser foot lifter
11
,GHQWL¿FDWLRQSODWH
19. Needle...6 Pre-tension guide
2. Thread cutter/holder
6. Handle
6
12. Cord socket 15. Thread guide
12
20. Bobbin cover release button
32. Feed dog control
17. Bobbin cover plate 24. Threading lever
4. Twin thread guide
21. General purpose foot...
Instruction Manual - Page 10
.... Open toe foot 24. Large extension table
The Foot that comes on your Sewing machine is another very useful foot and should not be sure they are SINGER Class 15J...a plate with guide 25. Thread spool net (short) 19. Darning / embroidery foot 22. Thread spool net (long) 18. Quarter inch foot with arrow on it on the back of the machine.
Screwdriver (large) 11. ...
Instruction Manual - Page 12
... any surplus oil from needle plate area EHIRUHXVLQJ\RXUPDFKLQHWKH¿UVWWLPH
POWER LINE CORD/FOOT CONTROL
Connect the plug of the power line cord into the machine socket (3), when using sewing machine only.
NOTE: In sewing mode, the machine can be disconnected from the walloutlet. Place a thread spool on the spool pin. The...
Instruction Manual - Page 14
... and the winding mechanism will stop when the bobbin is full. Put end of thread through thread guides as shown in illustration.
2. Place a spool of the thread, push the bobbin winder latch...
3. Holding onto the end of thread on the spool pin, and secure it through the hole in this machine.
1
1. Remove the wound bobbin and cut the thread tail.
12
Place bobbin onto the...
Instruction Manual - Page 18
... (5) from front to back. (See following page for instructions on operation of the Automatic Needle Threader.)
IMPORTANT: To verify that the machine is not raised, correct thread tension cannot be obtained.)
B. THREADING THE TOP THREAD
A. Turn the hand wheel counter clockwise (toward you do this simple check:
1.) With the presser foot raised, pull the...
Instruction Manual - Page 20
...
maintenir en place.
Pull thread gently into the twin thread guides (A and B). 3. Hook thread to cut and
hold it should not return to its lowest position until the twin thread guide rotates and stops.
Pull down the threading lever to particular qualities of the thread, or if the thread is in place. Thread the machine with your right hand. IMPORTANT...
Instruction Manual - Page 24
... the balanced tension of both top and bottom) is usually only desirable for straight stitch sewing. The tension is in the middle of layers of your fabric. ZIGZAG, SATIN STITCH, DECORATIVE and BUTTON HOLE SEWING
For zigzag sewing, satin stitch and decorative stitch functions, thread tension should be less than that for buttonholes. CHANGING PRESSER FOOT
Be sure...
Instruction Manual - Page 26
... this button to select that stitch.
3. Read more about the display when creating a stitch program.
2. For regular sewing, the LCD display shows the number of the selected stitch, an image of the stitch, and stitch width and stitch length settings. See page 26 - 27 for regular sewing and programming. The information on the machine straight stitch number 00, is selected...
Instruction Manual - Page 28
... the center of memory and stop. Turn the dial to adjust the selected setting. The settings made for all stitches when turning on programming the memory, see 3 above ) turning the Stitch Selection Dial will sew one . For more information on the machine. Turn the dial to browse the available stitches one by one sequence of the...
Instruction Manual - Page 30
... will preclude any possibility of the stitch you stop sewing. When the button is pressed, the LED indicator next to the Twin Needle button is activated. When turning the Stitch Selection Dial, the machine now automatically skips all stitches that Twin Needle Safety is lit.
7. Note: Twin needle safety and Thread cutting mode cannot be sewn with...
Instruction Manual - Page 32
... puntadas.
7. THREAD CUTTER
Press Thread Cutter to the button is due to sew. The lower speed continues until you sew thick fabric. If the low speed is lit red.
4
2. NEEDLE STOP POSITION SELECTOR BUTTON
When the machine is turned on, needle is cold or
when you stop position with lower LED lamp lit.
REVERSE STITCH BUTTON
Reverse sewing is...
Instruction Manual - Page 38
...use one of sewing. Start/stop the sewing machine. Thread tension control button I
4
2. Power/light switch
F G
2
NOTE: Since a straight stitch has no width, the stitch width control ...stop button F. Feed dog control (at its highest position, then raise the presser foot. Presser foot lifter H. Pull both Metric and Inch Markings as shown. Guide the fabric gently with the thread...
Instruction Manual - Page 40
... the foot control and the machine will sew 4 stitches in reverse and then 4 stitches in forward and stop.
38 Helpful Hint: Slight adjusting of the needle position to sew closer to the piping may be accomplished with desired top stitching color.
2. Press the reverse button and the machine will sew 4 stitches forward and then 4 stitches in with thread that the needle passes...
Instruction Manual - Page 68
... - 69). Machine jams/knocks. * Thread is bent or blunt. - STITCHING PROBLEMS Machine skips stitches. * Needle is being pulled or pushed against machine feeding
action. - Clean hook. (see page 24 - 27).
66 Stitches are lowered - Guide it gently. * Bobbin has not been wound evenly. -
Remove lint
(see page 64 - 65). PERFORMANCE CHECKLIST
GENERAL PROBLEMS Machine does not sew. * Power...
Instruction Manual - Page 74
... about 6" (15 cm) clear. It can also be entangled on each needle from front to sew with the foot or top thread may be used to your machine. Place a spool on the underside of the stitch you have selected. NOTE: Needle threader cannot be set above twin needle mark, regardless of fabric. To disengage...
Instruction Manual - Page 76
...the right to sew 5/8 of an inch seam allowances. Attention: Do not touch or move the knee lifter while sewing, otherwise the machine beeps with sewing techniques such as machine applique and free-motion sewing. It allows ... of the machine. To attach the guide, simply insert it ends. The edge guide/ quilting bar is used to sew perfect straight seams. It can be used to stitch parallel lines in...
Instruction Manual - Page 78
... stitch length, as this is determined by sewing speed and fabric movement. 2. Use a non-permanent fabric marking tool to secure them for repairing holes or torn areas, free-motion embroidery, creating monograms and stipple quilting.
Sew at the top of the presser foot is used for sewing. 3. Place the top fabric, batting and backing fabric together. MACHINE...
Instruction Manual - Page 82
...Stitch. Remove accessory box and slide table into place (if legs are in doll clothes or baby garments.
1. INSTRUCTIONS FOR SEWING...à la broche sous la table. QUARTER INCH FOOT WITH GUIDE
This Quarter Inch Foot with Guide gives a perfect 1/4" seam guideline, which is used... so that the needle is flush around sewing machine (unevenness of table could cause uneven feeding of cotton fabric,...
Similar Questions
What Is Error Code C 09
My Singer modern quilter keeps showing error code C 09. I do know what the problem is
My Singer modern quilter keeps showing error code C 09. I do know what the problem is
(Posted by karenkawycz 10 months ago)
E7 Error Code For 6199 Singer Brilliance Sewing.
How do I fix my sewing machine? E7 error code for 6199 brilliance.
How do I fix my sewing machine? E7 error code for 6199 brilliance.
(Posted by webnoakhills 3 years ago)
8500q Error Code C
What does the error code C stand for on the 8500q? After one stitch, the START/STOP Turns red and th...
What does the error code C stand for on the 8500q? After one stitch, the START/STOP Turns red and th...
(Posted by Julieames1980 4 years ago)
Error Code
I keep getting error code 16 on Singer 8500Q. I use it a lot to make flannel pillow cases for a char...
I keep getting error code 16 on Singer 8500Q. I use it a lot to make flannel pillow cases for a char...
(Posted by jmheaton 7 years ago)
Machine Does Not Stop Stitching Until Power Is Shut Off
When my machine is in default mode (straight stitching), it continues to stitch even after I have li...
When my machine is in default mode (straight stitching), it continues to stitch even after I have li...
(Posted by brosenberg129 10 years ago)