Singer 2932 Support Question
Singer 2932 Support Question
Find answers below for this question about Singer 2932.Need a Singer 2932 manual? We have 1 online manual for this item!
Question posted by Dizsand on June 19th, 2014
Automatic Threader--how Do I Use It. Have The Manual. Can't Understand Last Step
How do I use automatic needle threader. Have manual but do not understand the last step nor can I get anything from the picture. It is horrible
Current Answers
Answer #1: Posted by TechSupport101 on June 19th, 2014 8:59 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. Reach out straightly to Singer from here http://www.singerco.com/contact-us for clarity if the manual is sadly not helping.
Related Singer 2932 Manual Pages
Instruction Manual - Page 2
... properly, if it to the off the machine or unplug when the machine is used as threading needle, changing needle, threading bobbin, or changing presser foot, and the like.
10.Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any adjustments in the instruction manual.
11.Never drop or insert any other...
Instruction Manual - Page 6
... 6 Installing the snap-in sewing table 8 Connecting machine to power source 10 Changing the bulb 12 Two-step presser foot lifter/ Adjusting presser foot pressure.....14 Attaching the presser foot shank 16 Winding the bobbin 18 Inserting the bobbin 20 Inserting and changing needles 22 Threading the upper thread 24 Automatic needle threader 26 Thread tension 28...
Instruction Manual - Page 9
... parts of the machine
8
1. Presser foot
6. One step buttonhole lever
15. Stitch length dial
5
11. Stitch width dial
12. Pattern indicator window
13. Thread cutter
10
5. Automatic threader
7
14 15
13
PUSH
2 Reverse sewing lever
4
12
9. Thread take-up lever
2
4. Bobbin stopper
10. Presser foot pressure adjustment
9
3. Needle plate
3
11
7. Removable...
Instruction Manual - Page 17
Foot control The foot control pedal regulates the sewing speed. (3)
Attention: Consult a qualified electrician if in use . Unplug power cord when machine is not in doubt as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2)
Attention: Unplug power cord when machine is not in a polarized outlet only...
Instruction Manual - Page 21
... GB Two-step presser foot lifter
When sewing several layers or thick fabrics, the presser foot can be raised to a high rise position for heavy fabric, tighten by turning the screw counter counterclockwise, and for easy positioning of the work. (A)
A
Adjusting presser foot pressure
The presser foot pressure of the machine has been...
Instruction Manual - Page 25
Please Note: When the bobbin winder spindle is in "bobbin winding" position, the machine will not sew and the hand wheel will not turn. For smaller spools of thread place spool holder with small side next to right. (6)
- Step on spindle. (5)
-
Push bobbin to spool. (2)
- Place thread and spool holder onto spool pin (1). Snap...
Instruction Manual - Page 29
... of wear and causing problems. For best sewing results always use SINGER Brand Needles. Damaged points
2 22 Blunt needles C.
Loosen the needle clamp screw and tighten again after inserting the new needle. (1)
B. Bent needles B. D A
B C 1
GB Inserting and changing needles
Change the needle regularly, especially if it will go. Insert the needle as illustrated as it is showing signs of...
Instruction Manual - Page 31
... sewing machine is equipped with the thread coming off the power before threading.
- Pull about 6-8 inches of this process it is helpful to back. Lift up left through pre-tension spring as by leading thread down to the needle which should be found on the holder with the factory installed optional automatic needle threader, instructions for use...
Instruction Manual - Page 33
...the hook (D)
from bottom to its highest position. -
A C
A B
C
B
D
D
GB Automatic needle threader
-Raise the needle to top. - Press lever (A) down as far as it will go. - Release lever (A). - Pass the thread in front of the needle around thread guide (C). - A
2 26 Pull the thread through the needle eye.
1
Attention:
Turn power switch to the threading position (B). - The...
Instruction Manual - Page 41
... range thin to large. 9 (70) to thread size and weight of fabric.
Heavy duty thread, carpet thread. (Use heavy foot pressure-large numbers.)
IMPORTANT: Match needle size to 18 (110). For best sewing results always use the same thread on natural woven fabrics for double knits.
Natural woven fabrics-wool, cotton, silk, etc.
GB...
Instruction Manual - Page 51
.... Double overlock stitch: For fine knits, handknits, seams. Standard overlock: For fine knits, jerseys, neck edges, ribbing. Attention: Use new needles or ball point needles to suit the fabric. All overlock stitches are suitable for sewing and overcasting edges and visible seams in one operation. GB Overedge stitches
Seams, overcasting, visible hems. Turn stitch...
Instruction Manual - Page 55
... and insert the button (B). 5. Using tailor's chalk, mark the position of the gimp thread. 4. Set stitch length dial to " ". 2. Stop the machine when the buttonhole is completed, gently pull the heavy thread to remove any slack, then trim off the excess. While lightly holding the upper thread, start sewing. *Set the stitch width...
Instruction Manual - Page 65
Set the machine as for woven fabrics. (1)
When using Honeycomb stitch pattern for hemming sew at 1 cm (1/4") from the fabric edge and trim the surplus fabric. (2)
1
2
58 Set the stitch length dial to between "4" and "5". Set the stitch width dial to "S". This stitch can be used for all types of jersey as well as illustrated...
Instruction Manual - Page 67
Set machine as illustrated on both sides. Place patch in position. The stitch length can be shortened to produce very close stitches. (1)
When mending tears, it is advisable to use a piece of fabric and damage, sew between 3 and 5 rows. (2)
1
2
60 First sew over the center and then overlap on left. Depending on lace and elastic...
Instruction Manual - Page 71
...needle clamp screw (B). The lever (A) should be behind with your index finger and tighten the screw (C). (2) First sew around the edge of the hole (to right. It is recommended for easier sewing... the drop feed control to right to coordinate sewing speed and movement of fabric.
2 64
Note: Free motion darning is accomplished without the sewing machine internal feed system.
a b
ab
C 1...
Instruction Manual - Page 75
Lower the presser foot and alternately sew forward or reverse
using the lever. - For reverse sewing instructions, see page 32.
68 Turn stitch selector to the desired length. - GB Darning
- Position the fabric to be darned under the presser foot
together with the under laying fabric to be used. - Repeat this motion until the area...
Instruction Manual - Page 77
... under lap the fabric slightly as required by using the satin stitch to straight stitch, center needle
position. - Fold in the edge of the... fabric fold. - GB Attaching lace
- Turn stitch length dial to
under the folded edge of the lace. - You can add a decorative touch by the pattern of the fabric allowing it to the desired length. - Sew...
Instruction Manual - Page 87
... lifter to right so that it is easier to prevent uneven feeding of the seam when using the standard, regular foot on a wide range of fabrics from your machine.
Needle bar d.Needle screw & clamp e.Presser foot bar f . Your sewing machine offers excellent stitch quality on your left to raise the presser foot bar (1).
2. It also helps...
Instruction Manual - Page 89
...Use the brush supplied to clean the whole area (2). Replace the hook (5). Important: Fabric lint and threads must always be disconnected from the main socket. Your machine should be removed regularly. Remove the needle... hook race cover (4) and the hook (5) and clean with sewing machine oil. Turn the handwheel until the needle is in the left position. Snap the two hook retaining arms...
Instruction Manual - Page 91
.... Thread is too tight. Skipped stitches Needle breaks Loose stitches Seams gather or pucker Uneven stitches, uneven feed The machine is noisy The machine jams
1.The needle is not inserted correctly. 2.The needle is damaged. 3.The wrong size or type of needle has been used . 4.The needle is damaged. Lubricate as described. 3.Only use good quality sewing machine oil. 4.Replace the...
Similar Questions
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
My Singer 2932 Is Squeaking While Sewing. Have Cleaned All Areas, Keep It Oiled.
I use my singer 2932 daily and keep it oiled and cleaned from lint. I use good AlbaChem machine oil....
I use my singer 2932 daily and keep it oiled and cleaned from lint. I use good AlbaChem machine oil....
(Posted by blmoersch 6 years ago)
Singer 2932 Double Needle Use.
Can I use a double needle with this model? Singer 2932
Can I use a double needle with this model? Singer 2932
(Posted by roulx2 9 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)
Automatic Needle Threader
How do you use the automatic needle threader Singer h74?
How do you use the automatic needle threader Singer h74?
(Posted by Carlsondeb304 10 years ago)