Home » Singer » Sewing Machines » Singer 1004 VIVO

Singer 1004 VIVO Support Question

Find answers below for this question about Singer 1004 VIVO.
Need a Singer 1004 VIVO manual? We have 1 online manual for this item!

Singer Overview Questions Manuals Reviews Videos Research

Question posted by imonicasky on November 6th, 2015

Bobbin Plate

Hi, I lost the bobbin plate of my Singer Vivo sewing machine. Where can I get a new one. Which model series I should buy. Thank.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TechSupport101 on November 6th, 2015 9:58 PM

This answer was accepted by the poster of the original question.

TechSupport101

Member since:
May 24th, 2013

Points: 12,171,305

1,080
points

Hi. Go here http://www.singerco.com/support/replacement-parts-chart as I could not have much luck with third party parts retailers.

www.satechhelp.co.za

Related Singer 1004 VIVO Manual Pages

Instruction Manual - Page 1

...by bringing the thread down and think it down into the machine. VivoTM - 1004 INSTRUCTION MANUAL Now lower the presser foot, the thread should...bobbin thread and will not be replaced. Why is installed correctly.) Also, the flat part of this easy test to insert the needle halfway, clamp it is my machine...if they are sewing. With the presser foot lever in the tension of fabric you...

Instruction Manual - Page 2

... on the foot controller. 22. SINGER and VIVO are being used by the manufacturer or its intended use the proper needle plate. Special care is 72db . 20. To unplug, grasp the plug, not the cord. 19. Use this machine only for examination, repair, or electrical or mechanical adjustment. 7. Model 1004 VIVO INSTRUCTION MANUAL INTRODUCTION We recommend that...

Instruction Manual - Page 3

... Straight Stitching...18 Thread Tension...19 Reverse Sewing/Cutting the Thread 20 Zig-Zag Stitching...21 Blind Hem Stitching 22 Multi Zig-Zag Stitching 23 Darning Plate...24 Changing the Bulb...25 Maintenance...25 Troubleshooting...26 NAME OF PARTS PRINCIPAL PARTS OF THE MACHINE (Machine Front View) 1. Bobbin cover plate 13 16 19. Thread tension dial...

Instruction Manual - Page 4

...against the feed dogs. Bobbin Winding Stopper is required ...Plate is numbered from the presser foot holder. 12. Presser Foot Holder is an "L" setting for lower speed, and an "H" setting for sewing...sew smaller, more hard-to set the machine for the machine's accessories, keeping them at the back of the presser foot holder. Use only SINGER brand needles for the fabric while sewing...

Instruction Manual - Page 5

... lever to start the machine sewing. Use only SINGER® brand metal Class 15 bobbins in , making it to the right to the right of the take -up lever and the needle. It is located to release the cover when replacing the bobbin. 20. Hand Wheel controls the movement of the bobbin cover plate. Power Cord Socket...

Instruction Manual - Page 6

... the accessory storage compartment, flip the cover down, as other ), the plug is intended to fit in order to sew pants or sleeve hems, as well as shown. To turn the machine on the foot controller. If it as illustrated. Do not modify the plug in your right hand at the right...

Instruction Manual - Page 7

... the Power On/Off & Speed Control Switch to begin sewing. 11 12 Insert the new needle, with fabrics that the machine is properly threaded. NEEDLE / FABRIC / THREAD GUIDE There are various styles of needles available for this needle is 2045. Use this to use SINGER® brand needles. The most commonly used sizes are...

Instruction Manual - Page 8

... bobbin. Place the foot under the presser foot holder, then lower the presserfoot holder until the cut-out is magnetized. Contact your Authorized SINGER® retailer for the bobbin ...bobbins - using the Presser Foot Lifter. WINDING THE BOBBIN The Vivo create & repair machine by lifting the Presser Foot Lifter. Place the bobbin onto the bobbin winder as far as it around the bobbin ...

Instruction Manual - Page 9

... thread through the thread take -up lever from turning while sewing. INSERTING THE BOBBIN To insert the bobbin, first remove the bobbin cover plate. If it turns in order to left hand while firmly ...and replace it , put that end toward you start to the "off" position before threading the machine. THRE ADING THE UPPE R THRE AD Place the spool base, thread and spool cap onto the ...

Instruction Manual - Page 10

.... 4.Turn the hand wheel counter-clockwise (toward the back of the machine, leaving about 6" clear. Replace the bobbin cover plate. (1) (2) (3) (4) (5) (6) (7) (8) 17 STRAIGHT STITCHING The straight stitch is the most frequently used to select the stitch you want to sew lines up the bobbin thread. Guide the fabric with the red dot marking above the dial...

Instruction Manual - Page 11

.... fabric 20 As you come to lock the threads at the beginning and end of the sewing machine to ensure a well balanced stitch. You should detect only a slight resistance and little or ... foot and again pull the thread toward the back of the stitch when sewing in the bobbin. NOTE: The length of the machine. A well-balanced stitch is usually done at both threads, a smooth even...

Instruction Manual - Page 12

...possibilities. 1.Prepare the Appliqué Apply paper-backed fusible web to the wrong side of the machine and bobbin with a thread color that has been fused to the fusible web. Mix different types and ...durable finishing, particularly if the fabric is primarily used for hems on the look you sew. 3.When finished, fold the hem down and press. 21 22 Insert the appropriate needle for seam...

Instruction Manual - Page 13

... repairing a garment with the multi-stitch zig-zag. Be sure it in the Darning Plate. Use a hand sewing needle to pull the threads to snap it is a very versatile stitch. Note: It may be used. Mending a Tear Set the machine for Stitch 12 and attach the Satin Foot. Place a pin at the quarter...

Instruction Manual - Page 14

... type rated +- 1-(1) LED Φ5MM DC3V 0.6W - +- + + 1-(2) 2 3 4 MAINTENANCE 1.Wipe the machine with clean cloth. 2.Remove bobbin cover and take out the bobbin, place the bobbin cover back after cleaning with a small brush. 3.Keep the machine away from the main socket. CHANGING THE BULB Disconnect the machine from the power supply be removing the plug from high...