Ryobi RY39500 Support Question
Ryobi RY39500 Support Question
Find answers below for this question about Ryobi RY39500.Need a Ryobi RY39500 manual? We have 3 online manuals for this item!
Question posted by lgibson1506 on September 7th, 2014
Choke Lever Spring
so where does the spring and ball bearing go after i replaced the choke lever
Current Answers
Related Ryobi RY39500 Manual Pages
Operator's Manual - Page 5
.... accessory on United States Forest Service land, and Use only original manufacturer's replacement parts.
Do not overreach. carburetor adjustments.
3 - Follow all instructions listed below , can... instructions.
Limit the amount of hearing loss associated with sound
tightened and worn parts replaced. Do not
Wipe up any of the symptoms of this product, which could lead...
Operator's Manual - Page 6
... emergency.
Do not use this tool, loan them to instruct others who may use trimmer without front handles in place. Wear heavy gloves.
Replace any material over 3/4 in.
Operator's Manual - Page 8
... LOCK
The trigger lock prevents unintentional starting that all operating features and safety rules. English
Make sure that could result in the packing list are replaced. Fuel Tank Capacity 8.5 oz. Before use .
WARNING:
Do not attempt to possible serious personal injury. It also helps keep the blades from the operator's hands...
Operator's Manual - Page 9
... lock and throttle trigger. NOTE: Squeezing and releasing the throttle trigger releases the start lever to the RUN position. Failure to do so could result in serious personal injury. English... Failure to keep away from refueling site before fueling. Avoid spillage. Immediately replace fuel cap and hand tighten. WARNING:
WARNING:
Do not use of an oxygenated fuel ...
Operator's Manual - Page 11
...filter screen lightly to do so could get pinched or cut. All other parts should be replaced immediately.
For proper performance and long life, keep air filter clean. Remove the ... customer. WARNING:
Periodically inspect the blades for fuel leaks. If you will be repaired or replaced by pushing down on a flat surface. WARNING:
Do not at an Authorized Service Center. If...
Operator's Manual - Page 12
...repair is to the original factory specification before operating below 2000 feet. Use an exact replacement and replace annually. If you notice a power loss with your gas powered tool, you may ... for gasoline. STORING THE PRODUCT
Clean all fuel from corrosive agents such as garden chemicals and de-icing salts.
Abide by an authorized service center will improve performance...
Operator's Manual - Page 13
... approxi- Contact a servicing dealer. If engine does not start , repeat procedure with choke lever at idle.
Check lubricant fuel mixture. ment
11 -
Push primer bulb until bulb is...and emits excessive smoke.
The blades should not move choke lever to after three minutes, contact a servicing dealer. REMEDY
Clean or replace spark plug.
mately three minutes to "START" and...
Operator's Manual - Page 14
... INC.'S, OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS AND TECHTRONIC INDUSTRIES NORTH AMERICA, INC., DOES NOT ASSUME OR AUTHORIZE ... use of parts or accessories which vary from state to making the required repairs or replacements and no claim of breach of the original retail purchase. Spark Plugs, Carburetor, Carburetor...
Operator's Manual - Page 15
...Industries North America, Inc., warrants to conform with U.S. Any such part repaired or replaced under warranty will be aware, however, that a warranted part is scheduled only for... equipment is warranted for disallowing a warranty claim.
Any manufacturer-approved or equivalent replacement part may be grounds for three years.
Your emissions control system warranty applies ...
Operator's Manual - Page 16
... ASSY includes: Spark Plug X
ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR THREE YEARS OR FOR THE PERIOD OF TIME PRIOR TO THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
Your product has been fully tested prior to shipment to the maintenance section below. WARRANTY
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER...
Repair Sheet - Page 1
RY39500 all versions REPAIR SHEET RYOBI 26cc HEDGE TRIMMER
MODEL NO.
Repair Sheet - Page 2
MODEL NUMBER RY39500 2
1
22 25 12
21 20 19 23
Figure A
4 3
5
9 8
26 14
6 7
27 28
11 10
13
13
15
24
21
20
16
19
18 17
2 RYOBI 26cc HEDGE TRIMMER -
Repair Sheet - Page 3
MODEL NUMBER RY39500
PARTS LIST (FIGURE A)
KEY NO. PART NUMBER
DESCRIPTION
QTY
1
120900035 Front Handle (Inc. Key No. 14 1
12
308548011 Blade Assembly 1
27
678460002 * Lock Nut (M6 2
13
638659001 * Washer 2
28
678433004 Spring Washer 2
14
940686026 Starting Label 1 987000243 Operator's Manual (960713001)
10-03-08
15
901659001 Seal 1
(Rev:04)
* ...
Repair Sheet - Page 5
...678542003 Rotate Lock Spring 1
13
678509001 * Hex Nut (M5 x 0.8 3
14
308794003 Clutch Drum Assembly 1
15
638660001 Ball Bearing 1
16
678187002...Spring Washer 1
27
638554002 Washer 1
28
901665001 Felt Seal 2
29
308232001 Gear box Assembly (Inc. Key Nos. 14-20 1
* STANDARD HARDWARE ITEM - RYOBI 26cc HEDGE TRIMMER - MAY BE PURCHASED LOCALLY 5 MODEL NUMBER RY39500...
Repair Sheet - Page 7
...Washer 1
9
638284002 Spacer Tube 1
10
660970001 * Screw (M4 x 16 mm 3
11
308980003 Lower Housing 1
12
518820001 Starter Grip 1
13
900849002 Starter Rope 1
14
638033001 Spring & Container Assembly 1
15
518501001 Starter Pulley 1
16
638389001 Pulley Retainer 3
17
660967001 * Screw (M4 x 14 mm 3
18
308981007 Lower Housing Start Assembly
(Inc. RYOBI...
Similar Questions
Replacing Clutch Springs On Ryobi Brush Cutter
how do you change clutch springs on a ryobi 110 brush cutter
how do you change clutch springs on a ryobi 110 brush cutter
(Posted by mallynnwallace 11 years ago)
Ryobi Ry39500
How Large Is The Gap Between Flywheel And Coil Module
(Posted by maxpac 11 years ago)
Ryobi Ry29550 Choke
I have a new Ryobi RY29550 and the blade on the choke inside the carburetor is missing. Does one go ...
I have a new Ryobi RY29550 and the blade on the choke inside the carburetor is missing. Does one go ...
(Posted by winstonstroderd 12 years ago)
Choke Wont Lock In
is this model hedge clippers suppose to have a sprin and detent ball to lock the choke on when first...
is this model hedge clippers suppose to have a sprin and detent ball to lock the choke on when first...
(Posted by gbigelow2007 12 years ago)