Home » Ryobi » Lawn & Garden » Ryobi RY13050

Ryobi RY13050 Support Question

Find answers below for this question about Ryobi RY13050.
Need a Ryobi RY13050 manual? We have 1 online manual for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by sidneypaul on July 14th, 2012

Where Is The Spark Plug On The Ryobi 13050 Edger

The person who posted this question about this Ryobi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by hzplj9 on July 14th, 2012 7:50 AM

This answer was accepted by the poster of the original question.

hzplj9

Member since:
June 25th, 2012

Points: 4,875,690

1,100
points

This is a link to the breakdown diagram for the 13050.

http://www.ereplacementparts.com/ryobi-ry13050a-cycle-wheeled-edger-parts-c-7931_18673_129984.html

You are looking at the drawing for item number 11.

Related Ryobi RY13050 Manual Pages

Operator's Manual - Page 7

...sandals, or go barefoot. If you are approached, stop the engine and remove the spark plug wire before use . When operating the unit wear gloves to follow all safety instructions ...listed below may contribute to wear eye protection. If you are no sparks or flames. Wipe up any moving parts.  Keep all instructions listed below...

Operator's Manual - Page 8

... a dangerous situation.  Never stand or have any part of your hands on or near graveled surfaces.  If the edger strikes any type of foreign object: a) Stop the edger and remove the spark plug wire or disconnect from the cutting area.  Always keep your body in line with the path of the...

Operator's Manual - Page 10

...damaged or missing parts could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts. 6 - n Do not discard the packing material until ...Engine Displacement 30cc Engine Lubricant Volume 65 ml Fuel Volume 350 ml KNOW YOUR WHEELED EDGER See Figure 1. n Carefully remove the product and any parts are attempting. FEATURES ...

Operator's Manual - Page 11

... bolt and tighten securely. NOTE: Do not allow throttle cable to become pinched when installing the handlebar.  Insert the bolts through hole on the edger frame. Repeat with other side. Make sure the throttle cable and throttle trigger is on the right side as shown. English Make sure the hole...

Operator's Manual - Page 12

FUELING AND REFUELING THE EDGER  Clean surface around walkways, curbing, flower beds and other similar areas. from open flames and sparks. This unit is low, add engine lubricant until the fluid level rises to a machine with ANSI Z87.1. Lubricant level should not be emitted from a new ...

Operator's Manual - Page 13

...necessary. NOTE: This will set the carburetor to the START position.  Stand behind the edger and place your left hand on the handlebar. Using your right hand, pull the starter...cut to the eyelet. English To adjust the curb hopper wheel:  Stop the engine and remove the spark plug wire.  Loosen the adjusting knob and move the wheel arm up , if needed, to operate. ...

Operator's Manual - Page 14

.... WARNING: The blade should never turn the blade nut counter clockwise and remove.  Remove the old blade from the edger shaft.  Clean debris from spark plug. A dirty air filter will cause starting difficulty, loss of performance, and shorten the life span of lubricant used, and/or your gas powered tool...

Operator's Manual - Page 15

...approved container. The fuel cap contains a non-serviceable filter and a check valve. CHANGING EDGER BELT See Figure 17. Remove ring washer and blade guard.  Use a T25 ..., then squeeze it out.  Reinstall the air filter. SPARK PLUG REPLACEMENT This engine uses a Champion RY4C spark plug with warm soapy water. Tighten all components are qualified to perform this...

Operator's Manual - Page 16

... of the adjusting nut with one hand, loosen the retaining nut with a second wrench as garden chemicals and de-icing salts.  Abide by an authorized service center will overheat and... the adjusting nut until it is inaccessible to do so may result in poor engine performance, spark plug fouling, hard starting engine. In doing so, the engine will improve performance and allow that...

Operator's Manual - Page 17

.... Squeeze the trigger and pull the rope repeatedly until bulb is dirty. Spark plug fouled. Engine does not reach full speed and Air filter is flooded. ...runs. increase idle speed. Clean or replace spark plug. emits excessive smoke Spark arrestor screen is full of the spark plug hole, then reinstall the spark plug. 13 - NOTE: Depending on carburetor needs...

Operator's Manual - Page 18

...has been fully tested prior to shipment to ensure your product, call the Ryobi® Help Line! English WARRANTY Emissions Parts EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS... GASKETS X FUEL TANK ASSY INCLUDES: FUEL LINES X FUEL CAP X FUEL FILTER X IGNITION ASSY INCLUDES: SPARK PLUG...X ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR THREE YEARS, OR FOR THE PERIOD OF TIME PRIOR TO THE ...

Operator's Manual - Page 19

... to the operating instructions as commercial or rental. Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters B. TECHTRONIC INDUSTRIES NORTH AMERICA, INC., ASSUMES NO RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE OF RETURNING THE PRODUCT TO AN AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE OF DELIVERING IT BACK TO...

Operator's Manual - Page 20

...system. (ii) Intake manifold. (iii) Air filter. (3) Ignition System (i) Spark Plugs. (ii) Magneto or electronic ignition system. (iii) Spark advance/retard system. (4) Exhaust Gas Recirculation (EGR) System (i) EGR valve body...contact a Techtronic Industries North America, Inc., Customer Representative at any authorized RYOBI® Authorized Service Center, including any part that may be used ....