Ryobi RY10521 Support Question

Find answers below for this question about Ryobi RY10521.
Need a Ryobi RY10521 manual? We have 2 online manuals for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by longck122 on September 16th, 2012

Can Anyone Tell Me How I Can Get A Replacement Part For The Clutch/chain Cover

I'm trying to find the clutch cover or chain cover assembly replacement part for a RYOBI RY10521 Chain saw.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by longck122 on September 16th, 2012 10:00 PM

This answer was accepted by the poster of the original question.

longck122

Member since:
September 16th, 2012

Points: 40

1,090
points

The part # is 300957019

Related Ryobi RY10521 Manual Pages

Operator's Manual - Page 3

... area in the cut above chest height. • Follow the manufacturer's sharpening and maintenance instructions for the saw chain. • Only use replacement bars and chains specified by the manufacturer or the equivalent.  Do not operate a chain saw with both hands when the engine is intended for early morning or late afternoon hours when temperatures...

Operator's Manual - Page 4

...assembled. SPECIFIC SAFETY RULES WARNING: away from a ladder; Failure to follow all instructions may catch the saw chain and be whipped toward you or pull you off the engine before setting the chain saw down the saw...a fire extinguisher available when using chain saw.  Use only the replacement guide bars and low kickback chains specified for the saw. ■ Do not ...

Operator's Manual - Page 5

...; Loosen the fuel cap slowly to release pressure and to comply with the chain saw chain moves at idle speed after refueling. ■ Wipe spilled fuel from accident..., when operating this manual for the saw chain.  Never operate a chain saw chain stops moving when the throttle control trigger is not completely and securely assembled. REFUELING (DO NOT SMOKE!) ■...

Operator's Manual - Page 6

... Safety Alert Indicates a potential personal injury hazard. Do not operate in an enclosed area. DANGER! Wear non-slip, heavy-duty protective gloves when handling the chain saw properly with ANSI Z87.1 as well as hearing and head protection when operating this equipment. away. One Handed Carbon Monoxide Kickback Do not operate the...

Operator's Manual - Page 8

...chain saws. Kickback (Rotational) The rapid upward and backward motion of the saw which can occur when the wood closes in the cut the wood, and that supports and guides the saw chain. Low-Kickback Chain A chain that drives the saw chain. Page 8 - Clutch A mechanism for a chain... is bent or trapped under tension. Replacement Saw Chain A chain that cut along the top of cutting...

Operator's Manual - Page 10

... FULL CHOKE and RUN. CHOKE LEVER The choke lever opens and closes the choke valve in too deeply at the kickback zone. LOW KICKBACK SAW CHAIN The low kickback saw chain helps minimize the force of the guide bar from rotating. SAFE-T-TIP® ANTI-KICKBACK NOSE GUARD The SAFE-T-TIP® Anti-Kickback...

Operator's Manual - Page 11

...n Carefully remove the product and any parts are replaced. sories from the box. Use of a second is not completely assembled or if any parts appear to do not operate... this product. The use with this product with damaged or missing parts could result in serious personal injury. Failure to be missing or damaged. PACKING LIST Chain Saw...

Operator's Manual - Page 13

..., and is normal for the engine to emit smoke during and after the first use. Chain saw should use dirty, used, or otherwise contaminated lubricants. Damage may occur to replacing the fuel cap, clean and inspect the o-ring. n Immediately replace the fuel cap and hand tighten. n Fill the oil tank every time you fuel...

Operator's Manual - Page 14

... ( I ) posi- Fig. 5 STARTER GRIP WARNING: Keep your right foot onto the base of the chain line. Fig. 6 n Place the chain saw to an authorized service center for repair prior to the left of the rear handle. n Make sure the chain brake is cold or warm. Fig. 7 n Pull choke lever all the way out to...

Operator's Manual - Page 16

... authorized service center for adjustment and discontinue use . Do not put the chain saw , pull the choke lever out to the fully extended position (FULL CHOKE ) and engage chain brake to increase idle speed. NOTE: When you are finished using the chain saw chain still moves at idle, turn the idle speed screw "T" clockwise to stop...

Operator's Manual - Page 17

.... Either of the guide bar or when the wood closes in serious injury. It is made. If the saw . PULL PUSH Page 17 - As a chain saw is a lightning-fast reverse reaction which can result in and pinches the saw chain turning at the upper portion of the tip of the guide bar can cause the...

Operator's Manual - Page 19

... being pulled off balance. ■n Do not cut for professionals. ■n Cut only when visibility and light are cutting. WARNING: Alway use of using the chain saw except when felling a tree as the cut could result in serious personal injury. n Keep your weight with elbow locked in this operation for you begin...

Operator's Manual - Page 21

...24 VERTICAL CUT LOOSE SECTION HORIZONTAL CUT Fig. 25 Make the notch cuts so they do not touch the chain. n Make the backcut level and horizontal, and at a right angle to felling. The hinge controls ...prevents slipping or twisting or shootback of the tree off the saw and put it down immediately. n On large diameter trees, stop the chain saw , always make the lower cut of the notch before it...

Operator's Manual - Page 24

.... WARNING: Springpoles are dangerous. n Do not cut to reduce the weight. Do not stand on the saw . ■n When pruning trees it is cut off the limb further out to separate the log from ... climb into a tree to seal the wound. Watch out for your balance or control of the saw with a firm grip. This could strike the operator, causing the operator to lose control of springing...

Operator's Manual - Page 25

...normal operating conditions. REPLACING THE GUIDE BAR AND CHAIN See Figures 34 - 43. DANGER: Never start the engine before installing the guide bar, chain, clutch cover, and clutch drum. English ...cause product damage. Fig. 34 COMBINATION WRENCH BAR MOUNTING NUTS Fig. 35 CLUTCH COVER LUBRICATION All of the bearings in serious personal injury. RUN POSITION WARNING: ...

Operator's Manual - Page 26

... straighten any kinks. n Remove the clutch cover and the outer guide bar plate. n Lay out the new saw . n Place the chain drive links into the bar groove as shown. These components are in the long slot of the bar. n Remove the old chain from the mounting surface. n Position the chain so there is not set by...

Operator's Manual - Page 27

... snugly against the bar with the drive links in the bar groove. MAINTENANCE n Replace the clutch cover and bar mounting nuts. Ensure that the chain will not rotate. n Remove all slack from the chain by hand without binding. n Release the tip of the guide bar up and retighten the bar nuts securely. Lift the tip...

Operator's Manual - Page 29

... the wood, have an authorized service center sharpen the chain. Use only a low-kickback chain on this saw chain sharpened by an authorized service center or replace with a recommended low-kickback chain. ≈ .050 in. ≈ .050 in the areas indicated, have the saw . This fast-cutting chain provides kickback reduction when properly maintained. During maintenance of...

Operator's Manual - Page 34

... to adjustment of engine idle speed. AIR FILTER Fig. 64 STARTER COVER VENTS Fig. 65 IDLE SPEED SCREW "T" Fig. 66 WARNING: THE SAW CHAIN SHOULD NEVER TURN AT IDLE. English NOTE: If you use or sooner... n Clean the pre-filter every 5 hours of this manual. Remove the cylinder cover, starter assembly, and the fan housing baffle for drying, blow through both sides of debris. Use a ...

Parts List - Page 3

... SAW or when ordering repair parts. Scabbard (Model RY10519 1 20 in . PARTS LIST KEY NO. Guide Bar w/SAFE-T-TIP (Inc. T.F.)....... 1 Guide Bar Nut (5/16-18 2 Logo Label 1 Chain Cover Assembly 1 E-Ring 1 Cupped Washer 1 Sprocket Drum and Bearing Assembly (.325 chain 1 Chain Brake Label 1 Chain (.325 x 72 link, 18 in., Model RY10519).. 1 Chain (.325 x 78 link, 20 in., Model RY10521...