Ryobi P731 Support Question
Ryobi P731 Support Question
Find answers below for this question about Ryobi P731.Need a Ryobi P731 manual? We have 1 online manual for this item!
Question posted by Duce3304 on June 24th, 2012
Pinch Valve Adapter
pinch valve adapter on low pressure hose keeps popping out when inflating. Is this normal
Current Answers
Related Ryobi P731 Manual Pages
Manual 1 - Page 2
..., representations or promises as to the quality or performance of its RYOBI® power tools with the original product. WHAT THIS WARRANTY COVERS: This warranty covers all original equipment ... P.O. is not responsible for ninety (90) days. ADDITIONAL LIMITATIONS: Any implied warranties granted under normal usage and does not cover any case, within ninety (90) days or less. One World...
Manual 1 - Page 3
... all pressures within the system slowly. Contain long hair. Do not use common sense when operating an inflator. Many...inflator. WARNING! Do not place or store appliance where it on a ladder or unstable support. Keep proper footing and balance at least 18 in tool... new hose or notify an authorized service center for misalignment or binding of moving parts, breakage of the inflator in ...
Manual 1 - Page 4
...tool cords periodically and, if damaged, have repaired at pressure greater than marked maximum pressure of electric shock, do not expose to be performed only by inhaling toxic fumes.
Check damaged parts. Keep hose...this manual. Store indoors.
Inspect unit for the inflator. Entangled or snarled hoses can be properly repaired or replaced by unqualified personnel may ...
Manual 1 - Page 5
... chemicals are specially designed to filter out microscopic particles.
5 - Carefully monitor objects during inflation.
To reduce the risk of over inflation, use a reliable pressure gauge periodically during inflation.
Allow pump to these instructions. Never block the inflating or deflating outlets while operating.
Save these chemicals varies, depending on the...
Manual 1 - Page 7
... as well as air mattresses, rafts, floats, and other low pressure items requiring large quantities of applications. HOSE STORAGE
The inflator has twin storage areas located on each side of the tool.
PACKING LIST
18 Volt Inflator/Deflator Tapered Adaptor Sport Ball Needle Presta Valve Adaptor Low Pressure Hose with Pinch Valve Adapter Operator's Manual
WARNING:
If any parts appear to...
Manual 1 - Page 8
...
Improperly attached hoses or accessories can cause faulty pressure readings.
For every ten minutes of inflator use .
WARNING:
Always remove battery pack from the tool. To remove...Inflating high pressure items like motorcycle, car, and
bicycle tires Inflating and deflating low pressure items like air mat- tresses, rafts and floats NOTE: The inflator is secured...
Manual 1 - Page 9
...Clamp the end of the low pressure hose. To get an accurate reading, stop all pump operations. Insert pinch valve adaptor into pinch valve, insuring that the tip of the fluctuating pressure between the item and the high pressure hose. CAUTION:
Always leave low pressure hose free of inflation.
The inflator has two hoses for inflating high pressure items like air rafts, mattresses...
Manual 1 - Page 10
... the product. When not in use the Presta valve adaptor: Loosen Presta valve locking nut.
Thread Presta valve adaptor onto valve stem with any type of the tool.
INFLATING MANUALLY FOR HIGH AND LOW PRESSURE APPLICATIONS
Connect either high or low pressure hose to item to be used without adaptors to inflate a variety of items. To install accessory...
Manual 1 - Page 11
..., grease, etc. Do not attempt to comply with these warnings could result in objects being thrown into your eyes resulting in contact with ANSI Z87.1. Keep away from various types of commercial solvents and may result. Failure to destroy or disassemble battery pack or remove any of any time let brake...
Similar Questions
Pressure Reading...? 271.5, Car Tire, Is Impossible!! Was Trying To Check.
trying to fill a low tire, hooked up the "trusty" ole inflator and have continues to give me reading...
trying to fill a low tire, hooked up the "trusty" ole inflator and have continues to give me reading...
(Posted by Jquillin07 8 months ago)
My Tool Is Stuck In Cycle Mode The Fault Light Is Blinking And Won't Work
my crimper is stuck in cycle mode and fault light is blinking and tool won't work now
my crimper is stuck in cycle mode and fault light is blinking and tool won't work now
(Posted by Anonymous-174283 10 months ago)
Ryobi P731 Will Inflate Small Items Like Balls But Not Tires
(Posted by Jeffreystoker 2 years ago)
Where Can I Get An Adapter For My Re180pl
For 1&3/16' Template Guides?
(Posted by goblin 12 years ago)