Ridgid R4510 Support Question
Ridgid R4510 Support Question
Find answers below for this question about Ridgid R4510.Need a Ridgid R4510 manual? We have 2 online manuals for this item!
Question posted by kathylawshe on February 10th, 2014
Where Do I Find The Serial Number For A R4510 Ridgid Table Saw?
The person who posted this question about this Ridgid product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ridgid R4510 Manual Pages
Operation Manual - Page 1
TABLE SAW
R4510 / R45101
Your table saw has been engineered and manufactured to our high standards for buying a RIDGID® product. WARNING:
To reduce the risk of operation, and operator safety. Thank you years of rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE ...
Operation Manual - Page 3
... Never yank cord to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES. Learn the saw while it was designed. USE RIGHT TOOL. Don't use the next heavier...reduce the risk of wood on . KEEP WORK AREA CLEAN. The smaller the gauge number, the heavier the cord. DRESS PROPERLY. They can get caught and draw you ...
Operation Manual - Page 4
...personnel if the grounding instructions are included with saw or workpiece before transporting saw. NEVER use the rip fence during use.
NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT ...pinching and kickback, always support large panels. REMOVE ALL FENCES AND AUXILIARY TABLES before connecting to position and guide the work. NEVER stand or have repaired...
Operation Manual - Page 5
...pushed all through sawing. g) Never reach around or over the saw table for which it must
be used, including all the
way past the saw on the riving knife.
THIS TOOL should have ...POSITIONS where a sudden slip could cause your exposure, work . h) Never operate saw blade using the table saw blade guard and riving knife for every operation for wide or long workpieces.
...
Operation Manual - Page 8
...cutting operation along the length of the workpiece. Riving Knife (table saws) A metal piece, slightly thinner than the blade, which helps...in front of the saw blade tooth is not properly supported. Revolutions Per Minute (RPM) The number of a workpiece by ... the thickness of the saw during any angle to the workpiece, that area which a blade or cutting tool is being placed inadvertently ...
Operation Manual - Page 10
FEATURES
KNOW YOUR TABLE SAW
See Figure 3. Kickback is a hazard in which marks may be pulled back toward the operator. ...sides of the project you are available for use the tool.
10 Located on the workpiece. BEVEL ADJUSTING HANDWHEEL - BLADE GUARD -
LOCKING LEVER - This saw has an easy access power switch located below the saw blade, which helps keep the guard down over the ...
Operation Manual - Page 12
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and adjustments: FRAMING SQUARE
PHILLIPS SCREWDRIVER FLATHEAD SCREWDRIVER
COMBINATION SQUARE
C-CLAMPS
LOOSE PARTS LIST
The following items are included with your table saw:
ANTI-KICKBACK PAWLS
RIP FENCE
Fig. 5
SWITCH KEY
BLADE GUARD
MITER GAUGE
PUSH STICK
BLADE WRENCHES (2) 12
HEX KEYS (3)
Fig. 6
Operation Manual - Page 14
... help . Parts on the floor.
Carefully check the workbench after mounting to make sure the table saw is heavy. WARNING:
To avoid serious personal injury, always make sure that may have been ...are already assembled to your product when you have carefully inspected and satisfactorily operated the tool.
The saw is complete. To avoid back injury, keep your knees bent and lift with ...
Operation Manual - Page 16
...Figure 9. For the three remaining holes, insert the bolts through the hole in the table saw base on the leg stand.
Ignoring these precautions can result in the stand. Add ...
box), and a hex nut. ASSEMBLY
MOUNTING THE LEG STAND ON THE TABLE SAW BASE
See Figure 9.
WARNING:
Do not lift the saw base weighs approximately 75 lbs. Adjust the leveling foot with the holes in...
Operation Manual - Page 17
...TO OPEN THE LEG STAND
See Figures 10 - 12 Grasp the grips on the saw table and stand it upright as
shown below. Step on the release lever and pull the... toward the floor. With your hands on the grips, push the leg stand towards the ground until the table saw is in an open position.
GRIPS
Fig. 11
RELEASE LEVER
LEG STAND
Fig. 10 17
CENTER BRACE
RELEASE LEVER Fig...
Operation Manual - Page 18
... foot
until the leg stand no longer rocks. • Turning clockwise will lower the foot • Turning counterclockwise will raise the foot
TO STORE THE TABLE SAW ACCESSORIES
See Figures 14 - 15. WING NUT
PUSH STICK
LEVELING FOOT
BLADE
BLADE WRENCHES
WING NUT
MITER GAUGE
Fig. 13
ANTI-KICKBACK PAWLS
ANTI-KICKBACK...
Operation Manual - Page 19
.... Remove any workpieces from the body. Push the table saw until
the leg stand and saw are balanced on the release lever, grasp the
grips, and lift the handles up and away from the tool. Remove and securely store any tools or accessories such
as rip fence, miter gauge, clamps, blade guard...
Operation Manual - Page 23
...a dull, gummed-up, or improperly set blades. Keep your eyes, resulting in this tool. The use this device will greatly reduce the risk of cut wood and wood composition ... Cabinet making and woodworking NOTE: This table saw without the blade guard unless specifically instructed to comply with incorrect blade depth Sawing into your body in . Knock out any ...
Operation Manual - Page 26
... featherboard is an excellent project for ripping as discussed on page 32. wide and 18 in the saw table. Mark the center of the workpiece to avoid kickback that could cause serious personal injury. marks. ... to 30° and miter the other half of the blade. The end is angled with a number of short kerfs to give a friction hold on one -half of the width to the mark previously made...
Operation Manual - Page 27
... the angle of wood holding the wood firmly against the miter gauge.
Turn off the table saw blade is achieved, lock the blade height lock knob by pushing lever to 90°.
If the... USE THE IND-I -Cut is set so that the outer points of the saw blade are below the surface of the table saw table.
GULLET
TO LOCK
BEVEL LOCKING LEVER
Fig. 32 TO UNLOCK
HEIGHT ADJUSTING
KNOB...
Operation Manual - Page 32
...the handle.
When ripping a long workpiece, place a support the same height as the table surface behind the saw for the cut work.
Make sure the wood is clear of the wood as it ...; Once the blade has made , turn the saw off .
Let the blade build up to full speed before turning on the table saw.
Turn the saw on the table with both the rip fence and the surface of...
Operation Manual - Page 33
... the locking lever. Unlock the bevel locking lever. Turn the bevel adjusting handwheel until the bevel indica- VIEWED FROM THE FRONT, BELOW THE TABLE SAW
TO LOCK
TO UNLOCK
BLADE ANGLED
BEVEL LOCKING
LEVER
BEVEL CROSS CUT
MITER GAUGE STRAIGHT
Fig. 48
Fig. 49
33 OPERATION
MAKING A BEVEL CROSS CUT...
Operation Manual - Page 37
...6 in this manual and check with the retailer where the table saw is required for this procedure (refer to the Accessories section later in . This saw was purchased). Do not use push blocks, push sticks, ...shape and size of this saw on this tool. Failure to do so may be used to the tool. Once all dado cuts are necessary when making dado cuts to heed this tool. Failure to avoid the...
Operation Manual - Page 48
TABLE SAW
R4510 / R45101
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service center. Be sure to the motor housing.
OPERATOR'S MANUAL
10 in the space provided below. When ordering repair parts, always give the following information:
Model No. The model number of the authorized service center nearest you call 1-866-539...
Repair Sheet - Page 3
...x 12 mm 1 19 827470 End Cap (Right Rear 1 20 089037004700 Table Assembly (See Figure H 1 21 089037004044 Blade Cover 1 22 6362 Blade Nut 1 23 089037004043... Outer Blade Washer 1 24 089037004001 Blade (10 in . x 5/8 in . NUMBER
DESCRIPTION
QTY.
1 089037004006 Screw (M4 x12 mm 3 2 089037004049 End Cap (Left Front 1 3...NO. R4510
PARTS LIST FOR FIGURE A
KEY PART NO.
Similar Questions
Why Did My Ridgid Table Saw Power Die After I Turned It On?
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
(Posted by georgegll628 2 years ago)
Where Is Fuse For A Ridge Table Sawu
where is the circuit fuse for the R4510 table saw
where is the circuit fuse for the R4510 table saw
(Posted by hrabb 3 years ago)
Is There A Wiring Diagram For The R4510 Switch Actuator?
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
(Posted by djzinnicker 3 years ago)
Does Anyone Know How To Wire A New Switch To The R4513 Table Saw?
My saw has 5 wires coming out of it. (3 white, 1 black, 1 red) My new plug only has four plugs. What...
My saw has 5 wires coming out of it. (3 white, 1 black, 1 red) My new plug only has four plugs. What...
(Posted by groove104 8 years ago)
Does Anyone Have A Wiring Diagram For A Ridgid 4510 Table Saw
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
(Posted by joboptional09 8 years ago)