Ridgid MS255SR Support Question
Ridgid MS255SR Support Question
Find answers below for this question about Ridgid MS255SR.Need a Ridgid MS255SR manual? We have 1 online manual for this item!
Question posted by crystalsanning on June 10th, 2013
My Saw Runs Normal For A About A Minute Then It Powers Down Its Only 4 Months
The person who posted this question about this Ridgid product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ridgid MS255SR Manual Pages
Operation Manual - Page 1
OPERATOR'S MANUAL
10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR
� WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a RIDGID product. 1-866-974-3443/USA
SAVE THIS MANUAL FOR FUTURE REFERENCE
Operation Manual - Page 3
...tools sharp and clean for lubricating and changing accessories.
• Disconnect tools before plugging the tool into a blade or cut against the direction of rotation of the blade or cutter.
• Never leave a tool running...the risk of unintentional starting. Also use power tools in electric shock, fire and/or serious personal injury. The use of the tool, a guard or other condition that ...
Operation Manual - Page 4
...blade when it is running.
• Never use the fence. • Always keep sawdust from the power source and securely tighten the blade bolt.
• Never leave the saw table, and position it...Never use blades with the motor ventilation.
• Never lift this tool by power sanding,
sawing, grinding, drilling and other construction activities contains chemicals known to the State of chips...
Operation Manual - Page 5
... qualified person. • Always check the tool for misalignment or binding of electric shock, fire or serious injury. • Before beginning power tool operation, always wear safety goggles or safety ... tool's operation. Under some conditions and duration of the saw wears. • Inspect the tool cords periodically and, if damaged, have these instructions. Before further use of the tool,...
Operation Manual - Page 6
...the blade will allow you to operate the tool better and more safely. Proper interpretation of...speed
Designation / Explanation Voltage Current Frequency (cycles per second) Power Type of current Type of characteristic of these symbols will ... II construction Double insulated construction
Per minute
Revolutions, strokes, surface speed orbits, etc., per minute
Wet conditions alert
Do not expose ...
Operation Manual - Page 7
...increase the risk of normal safety precautions when operating this product. If the plug does not fit in property damage. This tool is within the voltage marked on the tool's data plate.
...surfaces such as pipes, radiators, ranges and refrigerators. This compound miter saw is grounded.
• Do not expose power tools to rain or wet conditions, and do not
attempt to touch ...
Operation Manual - Page 8
...power of the laser guide. Always make sure that any bystanders in a non-through cut without a reflective surface. Avoid direct eye exposure. Bright, shiny reflective surfaces are not suitable for the saw...stare into the beam. However, do not normally present an optical hazard. Only turn the ...location when using the tool. Do not stare into the beam. lasers
This miter saw has a built-...
Operation Manual - Page 9
...tool is mounted.
• Throat Plate: A plate inserted in the Miter Saw's table that allows for blade clearance.
• Through Sawing...Capacity of the miter-table base.
Wavelength: 635nm, Power ≤ 1mW Class II
2x12, 4x4
2x8,...Minute (RPM): The number of turns completed by a spinning object in one minute.
• Saw-Arm Locking pin: Locks the saw arm in the "DOWN" position.
• Saw...
Operation Manual - Page 11
... The work piece. Press the right bevel range control lever down and the saw is equipped with sufficient power to securely clamp the work piece.
Right bevel range control LEVER With the ...YOUR SLIDING COMPOUND MITER SAW The safe use of this product requires an understanding of the information on the tool and in this tool. Spindle-lock button
15 AMP motor This saw arm. One end...
Operation Manual - Page 12
Tools needed
The following tools (not included) are needed for making adjustments:
3mm Hex key
Loose parts
The following ...8226; Operator's manual
Blade wrench
Combination square 3/8" Open-end wrench
Fig. 3
OPERATOR'S MANUAL
10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR
Dust bag
Hex key
� WARNING: The use of injury, the user must read and understand the operator's manual ...
Operation Manual - Page 13
...Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool. • The saw from the carton by the carrying
handle and place it , check for accuracy as...product requires assembly. • Carefully lift the saw is factory set for accurate cutting. If shipping has influenced the settings, refer to a power supply until the missing parts are for use...
Operation Manual - Page 16
... and the heel of the square against the teeth of the blade, and not against the saw arm when it is set screws clockwise or counter-clockwise with a 3/8" open-end wrench. ...not included). Loosen the lock nut on page 16. NOTE: If the bevel-lock lever does not secure the saw blade. Lift the bevel-lock lever to 0°. adjustments
ADJUSTING THE BLADE TO THE MITER TABLE 45°...
Operation Manual - Page 18
...; stop plate can be adjusted.
5.
Unplug the saw.
� WARNING: Failure to unplug your saw serviced by itself, or if there is play in...saw arm in Fig. 18a; adjustments
ADJUSTING THE BEVEL STOP TO 48° LEFT Two 45° to 48° stop plate
Fig. 18b
17 Lock and tighten the bevel-lock lever.
PIVOT ADJUSTMENTS
NOTE: These adjustments were made at the factory and, under normal...
Operation Manual - Page 19
...; WARNING: Always wait for the blade to stop
completely, and unplug the tool before using the laser light.
1. Lock the saw arm by the handle on , and, if the cut to get a cutting...saw, then lower the saw arm and lock it in place.
4.
Insert the work piece in the "DOWN" position. Adjust the work piece clamp to firmly clamp the work piece clamp into one of the miter saw into the power...
Operation Manual - Page 24
... the work piece.
� CAUTION: Always perform a "dry-run" cut to
determine whether the operation being attempted is possible before power is against the fence, the board could result in
accidental start ..., causing it will engage automatically and turn off button to release the saw .
23 Before turning the saw on the bevel scale. Slowly lower the blade into and through the work...
Operation Manual - Page 28
...blade at the end of the saw .
3. The setup of the cut and jam the blade.
4. NOTE: Always perform a dry-run cut so you can be cut on a miter saw
Fig. 33
27 Align your...clamps (not supplied), and place tape on the area being attempted is possible before power is applied to miter saw depends on the base molding characteristics and applications, as shown. Carefully follow all ...
Operation Manual - Page 32
...blade-screw guard into the upper blade guard and then placing the blade in the miter saw arm. 3. Lower the saw . 2. Loosen the screw with the arrow on the
end of the blade
flange is ...operator.
1. Match the arrow on the blade with the Phillips screwdriver on the
upper blade guard. Unplug the tool. 2. Make sure that the inner blade flange (Fig. 37b) is released so the blade will rotate ...
Operation Manual - Page 33
... by a qualified service technician at any other . 5. BRUSH REPLACEMENT Fig. 38
The saw has externally accessible brush assemblies that can damage, weaken, or destroy plastic. Check for...2. Remove the brush cap with side shields during power tool operation or when blowing dust. length of the unit under normal operating conditions. Proceed as follows when replacement is spring...
Operation Manual - Page 35
...MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY. Chervon North America and RIDGID&#... Inc.
All warranty communications should be transferred.
To receive a replacement tool you must be disclaimed under normal usage and does not cover any reason you by calling (toll free...
Operation Manual - Page 36
Be sure to the motor housing. The model number of this tool is found on a plate attached to provide all relevant information when you call 1-866-974-3443. MS255SR
35 OPERATOR'S MANUAL
10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR
CUSTOMER SERVICE INFORMATION
For parts or service, call . When ordering repair parts, always...
Similar Questions
Ms255sr Ridgid Miter Saw Fence
Hi, I am looking for the fence for the MS255SR. It has been difficult to find the part number. If I ...
Hi, I am looking for the fence for the MS255SR. It has been difficult to find the part number. If I ...
(Posted by jqjrpr 1 year ago)
Why Did My Ridgid Table Saw Power Die After I Turned It On?
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
(Posted by georgegll628 2 years ago)
Does Anyone Have A Wiring Diagram For A Ridgid 4510 Table Saw
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
Hi. A few monthe ago I took my motor out of my Ridgid 4510 saw to have it repaired. Disassembly was ...
(Posted by joboptional09 8 years ago)
Saw Blade Stops On Cut
why does mitter saw blade stop in the middle of the cut
why does mitter saw blade stop in the middle of the cut
(Posted by amazingwoodflooring 8 years ago)
I Brought Ms255sr From A Action . Looks New . The Motor Runs Very Slow And No Po
Moter runs very slow and has no power & does not speed up ms255sr . Is there any fuse or relay d...
Moter runs very slow and has no power & does not speed up ms255sr . Is there any fuse or relay d...
(Posted by Cep3pal 8 years ago)