Ridgid MS255SR Support Question

Find answers below for this question about Ridgid MS255SR.
Need a Ridgid MS255SR manual? We have 1 online manual for this item!

Ridgid Overview Questions Manuals Reviews Videos Research

Question posted by Cep3pal on September 13th, 2015

I Brought Ms255sr From A Action . Looks New . The Motor Runs Very Slow And No Po

Moter runs very slow and has no power & does not speed up ms255sr . Is there any fuse or relay defect . Thank you

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on October 16th, 2015 8:24 AM

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,793

100
points

Click here for a possible solution. You may also download the manual from the link below and refer to the maintenance chapter for any possible fix.

https://www.helpowl.com/manuals/Ridgid/MS255SR/182571

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Ridgid MS255SR Manual Pages

Operation Manual - Page 1

Thank you for buying a RIDGID product. 1-866-974-3443/USA SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR � WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product.

Operation Manual - Page 2

table of contents General Safety Instructions 2 Specific Safety Instructions 3 Additional Instructions for Safe Operation 4 Symbols 5 Electrical 6 Lasers 7 Glossary 7 Features 8 Tools Needed 11 Loose Parts 11 Assembly 12 Adjustments 13 Operation 18 Maintenance 31 Troubleshooting 33 Warranty 34

Operation Manual - Page 3

... is a combination of using an extension cord, be kept at all instructions. Turn the power off position before plugging the tool into a blade or cut against the direction of rotation of the blade or cutter. • Never leave a tool running unattended. If in working order. • Remove adjusting keys and wrenches. Non-slip footwear...

Operation Manual - Page 4

... Should this tool by gripping ...running. • Never use dull or damaged blades. Wear protective clothing and wash exposed areas with dust from the power...defective or incorrect. • Always keep blades clean, sharp and with the motor ventilation. • Never lift this ever occur, stand clear and allow the motor to come to a power supply. • Keep the motor... cutting speed for ...

Operation Manual - Page 5

... a dust mask if the operation is marked to determine whether it will reduce the risk of electric shock, fire or serious injury. • Before beginning power tool operation, always wear safety goggles or safety glasses with ANSI Z87.1. • Protect your lungs. Under some conditions and duration of use, noise from the...

Operation Manual - Page 6

... Watts Alternating current Direct current No-load speed Designation / Explanation Voltage Current Frequency (cycles per second) Power Type of current Type of characteristic of current Rotational speed at no load Class II construction Double... involve your hands away from the blade will allow you to operate the tool better and more safely. Always wear safety goggles or safety glasses with any...

Operation Manual - Page 7

... operation of grounded outlet box • If operating a power tool in damp locations is unavoidable, always use power tools in the tool, be performed only by a qualified person. Keep the ...supplied is intended for damage. Always wear electrician's rubber gloves and footwear in any power tool can result in the outlet properly, reverse the plug. When servicing, use only ...

Operation Manual - Page 8

... surface. Do not perform any bystanders in accordance with a button switch that emits a maximum output power of wood so that permits other than the work piece from a block of 635 nm 1 mW...twisting or moving during the cut made using the tool. Avoid direct eye exposure. Any repairs must be used and maintained in the vicinity of looking directly into the laser. � WARNING: LASER...

Operation Manual - Page 9

...does not extend completely through the thickness of the work piece; FEATURES SPECIFICATIONS Motor No-load Speed Blade Diameter Arbor Size Laser Cutting Capacity with Miter at 0°/Bevel 0&#...0°/left and right side of the blade, as faces, ends, and edges. Wavelength: 635nm, Power ≤ 1mW Class II 2x12, 4x4 2x8, 4x4 2x12 2x12 6" 59.6 lbs. (27.1 kg... or cutting tool is performed.

Operation Manual - Page 11

...tool. Press the right bevel range control lever down and the saw arm and the end of the operating features and safety rules. 10 inch blade Your compound miter saw has a powerful 15 amp motor...33.9° (USA)/ 30° (CANADA) STOP BLOCK Use this product, familiarize yourself with sufficient power to securely clamp the work -piece widths. Bevel-lock lever To lock the saw at bevel 33.9&#...

Operation Manual - Page 12

...-end wrench Fig. 3 OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER MS255SR Dust bag Hex key � WARNING: The use of injury, the user must read and understand .... Thank you for a bevel cut crown molding at 45° right or left miter with your sliding compound miter saw head into the optimal position to accurately cut . Tools needed The following tools (not...

Operation Manual - Page 13

...is factory set for interference between the blade and the miter fence. NOTE: This tool is noted, secure the workbench to accommodate the saw has been shipped with this manual... condition. Carefully check the workbench after mounting to a power supply until you have carefully inspected and satisfactorily operated the tool. • The saw base for this warning could result...

Operation Manual - Page 19

...some operations, the clamp assembly may require several cycles. Use the work piece clamp into the power source and make sure that there is no interference with the hex key provided. Plug the ...observed or suspected. � WARNING: Always wait for the blade to stop completely, and unplug the tool before using the laser light. 1. Adjust the work piece clamp to the next step. � ...

Operation Manual - Page 20

..., press the clamp knob while rotating the work piece clamp (Fig. 19c). � WARNING: When using the work piece binding the blade will cause the motor to the desired angle.

Operation Manual - Page 24

...the "No-Hands Zone," as indicated on the scale) to reach maximum speed. 16. If the board is longer or wider than 90° ... a cut to determine whether the operation being attempted is possible before power is applied to make sure that it to do so could collapse on ... of the work piece. � CAUTION: Always perform a "dry-run" cut . 4. Allow the saw blade to secure the saw into ...

Operation Manual - Page 28

... the saw . Splintering typically happens due to miter saw Molding standing up against fence (before power is possible before clamping) Fence Bevel at 0° Miter saw Fig. 33 27 Molding lying... could collapse on the base molding characteristics and applications, as shown. NOTE: Always perform a dry-run cut so you can be cut on a miter saw depends on the blade at 0° Fence...

Operation Manual - Page 33

...servicing, use . Remove the brush cap with side shields during power tool operation or when blowing dust. length of the motor and that the brush cap is dusty, also wear a dust... unit under normal operating conditions. Tighten the brush cap securely. GENERAL MAINTENANCE Avoid using new brush assemblies. LUBRICATION All of the bearings in . Unplug the saw has externally accessible...

Operation Manual - Page 34

.... 2. Motor brake overheated from use of cut is inaccurate. 1. Brush worn. 1. Brush worn/damaged. See MAINTENANCE section. Angle of defective or wrong size blade or rapid On/Off cycling. 3. Too much sawdust under table. 2. Parts failure. 2. Improper operation. 2. Tighten arbor bolt. Arbor bolt is released. 1. Use a recommended blade. 3. Check time delay fuse or...

Operation Manual - Page 35

... is manufactured by applicable law, all original equipment packaged with the tool such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in workmanship or materials... limitations on RIDGID® Hand Held and Stationary Power Tools covers all defects in this RIDGID® tool you . The replacement tool will repair any faulty workmanship, and either repair...

Operation Manual - Page 36

... ordering repair parts, always give the following information: Model No. The model number of this tool is found on a plate attached to provide all relevant information when you call 1-866-974-3443. Serial No. Be sure to the motor housing. MS255SR 35 OPERATOR'S MANUAL 10 INCH SLIDING COMPOUND MITER SAW WITH DUAL LASER...