Ridgid GP90150 Support Question
Ridgid GP90150 Support Question
Find answers below for this question about Ridgid GP90150.Need a Ridgid GP90150 manual? We have 1 online manual for this item!
Question posted by Catbalk on July 24th, 2017
Does The Throttle Cablehave A Bracket That Connects It To The Engine Lever
gp90150a wheelbarrow gas air compressor. I don't know if the throttle cable hooks up to anything up on the engine besides where it mounts it looks like a connects to the lever one time but I think it's broke don't know don't have the manual it's never ran right from the beginning when it's trying to fill with air
Current Answers
Related Ridgid GP90150 Manual Pages
Owners Manual - Page 1
GP90150A
OPERATOR'S MANUAL
WHEELBARROW AIR
COMPRESSOR
To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. IN629100AV 12/08
Printed in U.S.A.
Owners Manual - Page 2
... Warning 5 Warning Labels 6
Glossary of Terms 7
Unpacking and Checking Content 7
Getting to Know Your Air Compressor 8
Operating Your Air Compressor . . .10 Moisture in Compressed Air . . . . . .10 Lubricaton 11 Start-up 11 To Start Gasoline Engine 12
Section
Page
Maintenance 13 Maintenance Schedule 13 Tank 14 Filter Removal, Inspection, and Replacement 14 Drive Belt 15 Storage...
Owners Manual - Page 3
...very important to know and understand. Caution... Occupational Safety and Health Act (OSHA).
3. Check all fasteners at all times:
1.
Personal injury or property damage could occur from contact with these rules..., COULD result in Canada CSA Z94.3-99) and use the compressor.
4.
Before Using the Air Compressor
CALIFORNIA PROPOSITION 65
This product or its power cord may cause ...
Owners Manual - Page 4
... rupture or explosion. To reduce fire hazard, keep engine/motor exterior free of the compressor. Do not tamper with governor setting on engine. Welding, drilling or any spilled gas before starting the engine.
Keep safety valve free from a running or hot engine. Check fuel level before starting the engine. If the equipment should start to repair or...
Owners Manual - Page 5
... shall be voided, and Campbell Hausfeld disclaims any application of air for unsafe conditions such as is not simultaneously used for the purpose of open flame or near ignition sources including the compressor unit.
19. Allow engine to minimize overspray accumulation on the compressor.
22. Do not direct paint or other flammable substances.
20...
Owners Manual - Page 6
Safety Instructions (continued)
Warning Labels
Find and read all warning labels found on the air compressor shown below
DK724100AV 10003
6
Owners Manual - Page 7
... A combination of an air tool with an air requirement higher than the compressor's rated delivery. It is stated as (number) SCFM at which a compressor starts and stops while refilling the air tank.
Remove the air compressor from the carton.
2. Place the compressor on the compressor
SCFM (Standard Cubic Feet per Minute) Sometimes called CFM (Cubic Feet per Square Inch) Measurement...
Owners Manual - Page 8
Getting to Know Your Air Compressor
1 Beltguard
2 Air Filter 3 Dipstick/Oil Sight Glass
4 Handles
6 Unloader 7 Air Storage Tank
5 Tank
Drain Valve
8 Regulated
Outlet Gauge
9 Regulator Knob
10 Tank
Pressure Gauge
11 ASME
Safety Valve
12 Air Outlet Fittings
ridgid.com
1-800-474-3443
DK724300AV 0104
Model/Serial Number Decal
8
Owners Manual - Page 9
... Gauge. Gauge shows pressure in air receiver indicating compressor is measured in the compressor pump.
Air Storage Tanks. The tanks store air for later use.
9 This knob controls air pressure to move the compressor.
5. It protects the user from outlet.
9. Used to an air operated tool or paint spray gun. Unloader. When loaded, the engine will run at the outlet...
Owners Manual - Page 10
... period of time, this moisture will collect in compressed air will form into droplets as it ineffective. When humidity is high or when a compressor is completed ...Do not attach air tools to the gun as droplets mixed with the compressed air. Operating Your Air Compressor
Before starting the compressor, thoroughly read all component instruction manuals, especially the engine manual. Failure...
Owners Manual - Page 11
... a level surface.
1. Dipstick Add Oil
Max Fill
Low Line
Full Add Oil
Start-Up
To ensure proper operation, unit must be used. Turn manual unloader lever up to a horizontal position to allow the compressor pump to run without compressing air. Fill engine with oil and gasoline per instructions furnished with oil.
Owners Manual - Page 12
... unloads, bringing the engine to idle. See gas engine manual for approximately 30 minutes to the open position. The compressor will begin to the loaded position. The engine then accelerates and the compressor pumps additional air into the tank.
Operating Your Air Compressor (continued)
To Start Gasoline Engine
4. After approximately 30 minutes, move the choke lever to break in...
Owners Manual - Page 13
... valve and allow the ring to snap back to maintain efficient operation of the compressor system, check the air filter weekly (per maintenance schedule), oil level and gasoline level before attempting to tamper with the ASME safety valve!
With engine OFF, clean debris from the system before each use. In order to normal...
Owners Manual - Page 15
.... 2. The belt must be properly aligned when adjustment is a result of normal use , hose and compressor should be stored in a cool, dry place.
2. Loosen the four fasteners holding the
engine to the straight edge. 6. To align belt, lay a straight edge against the face of moisture.
3. Tanks should be disconnected and hung with...
Owners Manual - Page 16
... and run the air compressor while troubleshooting. TROUBLE
Low discharge pressure
PROBABLE CAUSE 1. Air leaks
2. Remove head and inspect for escaping air. The belt should deflect about 1/2" under 5lbs of leakage. Tighten or replace leaking fittings or connections
2. Low compression
16
Be sure that the engine pulley is perfectly aligned with a new one each time the head...
Owners Manual - Page 17
... 2. Check oil level. Lack of pump and motor/engine
Excessive belt wear
1. Replace connecting rod 4. Replace excessively worn piston pin or pistons, as required
17 Check for excess wear. Loose engine or compressor pulleys are a very common cause of cool, clean, dry and well-circulated air is available
2. Dirty cooling surfaces
REMEDY
1. Adjust tension or...
Owners Manual - Page 18
... oil
6. Connecting rod out of piston. Replace rod
18 Worn bearings 6. Replace worn bearings and change oil
6. Replace
1. Restricted breather
4. Troubleshooting
TROUBLE Excessive noise (knocking) Continued
Oil in the intake system 3. Worn piston rings 2. Compressor air intake
restricted
3. Drain down to full level
5. Replace head and valve plate using new gasket
7. Check...
Owners Manual - Page 21
... control
1
* Throttle unloader
1
* Gauge, outlet
1
* Coupler
2
* Regulator assy. (includes 21, 22 & 24)
1
* Gauge, tank
1
Pump
1
Discharge tube
1
Flywheel (includes 2)
1
Pulley
1
3/16" Key
1
Square head setscrew
1
Brace assembly
1
Engine
1
Hex head screw
4
Washer
8
Locknut
4
Wire retainer
1
3/8" Flange nut
1
3/8" Shoulder bolt
1
Beltguard bracket (motor...
Owners Manual - Page 23
...
ST022300AV
1/8" NPT oil drain plug
1
4
18143
VT040300AG
Crankcase
1
5
- G
Crankcase gasket
1
6
18148
ST084202AV
Ball bearing
2
7
18153
VT040600AJ
Crankshaft assembly
1
8
18158
VT040100AG
Connecting rod
2
9
18163
VS001400AV
Piston pin
2
10 L 18168
TQ011900AG
Piston
2
11 I - G
O-ring
1
16 G 18178
ST129700AV
Oil seal
1
17 18183
-
G
Cylinder gasket...
Owners Manual - Page 24
... OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING AS NOTED BELOW.
GP90150A
Catalog No. IN629100AV
Printed in this RIDGID air compressor for this air compressor. GP90150A
© 2008 RIDGID, INC. IN629100AV 12/08 Form No. in a safe place for other RIDGID products may vary. Part No. Gasoline engines and components are not covered by Campbell Hausfeld. HOW TO...
Similar Questions
Bevel Lock Lever Is Locked And Unable To Unlock It, Saw Stuck To The Right.
(Posted by minnoweyesbus 2 years ago)
Rigid Spindle Sander Manual Changing The Belt To A Simple Spindle Sander.
Can't seem to locate my manual and want to change the belt configuration to a simple single spindle ...
Can't seem to locate my manual and want to change the belt configuration to a simple single spindle ...
(Posted by evace109 8 years ago)
Shop Repair Manual
Am looking for a shop/repair manual (not the owner manual) for a Ridgid R4331 bench top planer.
Am looking for a shop/repair manual (not the owner manual) for a Ridgid R4331 bench top planer.
(Posted by jimshoe52 8 years ago)
How To Connect The Belt What Two Points Of The K-380 Machine Are Belt Pulleys
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
(Posted by popsrea1 9 years ago)