Home » Pyle » Home Theater Systems » Pyle PT4601AIU

Pyle PT4601AIU Support Question

Find answers below for this question about Pyle PT4601AIU.
Need a Pyle PT4601AIU manual? We have 1 online manual for this item!

Pyle Overview Questions Manuals Reviews Videos Research

Question posted by nick9746 on September 8th, 2015

Blown Fuse On Pyle Receiver

The Master Volume does not work on my Pyle PT4601AIU receiver. The light on the dial won't even turn on. I believe it is a blown fuse. Any advice on where to find the fuse and how to fix the problem will be appreciated.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on September 10th, 2015 10:43 AM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,813

1,100
points

NOTE: Because each of these steps represents a possible solution to this issue, check the power status after completing each step.

Yes that could be a blown fuse, there is a fuse at the back of the unit to check.

Make sure the power cord of the unit is securely connected to a working power outlet.
If the power cord is plugged into a surge protector, disconnect the surge protector and plug the power cord directly into the wall outlet.
Plug the unit into a different power outlet to make sure there is not a problem with the current power outlet.
If the unit has a voltage switch on the rear of the unit, make sure the switch is set to the correct voltage for your area. NOTE: Some unit have a 110 to 220 voltage switch on the rear of the unit where the default setting is 220V. Verify that this switch is set to 110V.
Press and hold the POWER button.
While pressing the POWER button, unplug the power cord from the power outlet.
Release the POWER button.
Plug the power cord back into the power outlet and try powering the system back on.
Make sure that nothing is blocking the ventilation holes on the rear of the unit and that it is placed in a location with adequate ventilation. NOTE: If the unit has been in use for more than three hours with the volume set at a high level, unplug the power cord for one to two hours to reset any output generators that may be installed inside the unit. This will avoid overheating and will prevent any further damage to the unit.
If applicable to your model, reset the unit
If the issue is still unresolved, service may be required.

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Pyle PT4601AIU Manual Pages

PT4601AIU Manual 1 - Page 2

...-amp and subwoofer I) All the blue lights and blue rings gain control through LED...cable It Digital karaoke system It Over heat,over current protection 1...anything, especiall y metal, inside this Pyle Pro amplifier. Contact your living room....smell or smoke is detected, immediately turn the power OFF and pullout the power... media center of applications. This Pyle Pro hybrid amplifier also has sub...

PT4601AIU Manual 1 - Page 4

... sensor should be far away from the light,high amounts of receiver. 2. TUNING> TUNING< The two keys are used to adjust to AC llOV/60Hz&220V150Hz outlet. 5 PT4601AIU 10- ---1 1.AUXlUSB 1 AUX/USB...store SO statioDS 7.MEMORY After a station has been found you r the other spea ker system(s) to these terminals. (4 )8 SPEAKEROUTPUTTERMINALS Connect you can affect its performance. NEXT> PREV<...

PT4601AIU Manual 1 - Page 5

PT4601AIU PT4601AIU AM ANTENNA FMANT-EN,N-A 2MIC I I e ___ e •• ) $PEAKER/lMPEDANCii 1.;4~-1lgIlPEAKEII It4g-1lgllPEAKEII •• 8 8 •• ..~ ~ ' 0 RnY- ~.~~ · PUTS/ / II tg,poDor MP3;npu' I •• I ..