Home » Poulan » Lawn & Garden » Poulan PP5524ESC

Poulan PP5524ESC Support Question

Find answers below for this question about Poulan PP5524ESC.
Need a Poulan PP5524ESC manual? We have 1 online manual for this item!

Poulan Overview Questions Manuals Reviews Videos Research

Question posted by iuwu01 on February 17th, 2014

My Poulanpro Pp5524esc Is Stuck In Forward In The Highest Speed

I cannot dis engage it I disconnected the linkage and it appears to be stuck somewhere in the housing

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Poulan PP5524ESC Manual Pages

User Manual - Page 1

Always Wear Eye Protection During Operation 192030 07.29.04 BY Printed in serious injury. Failure to do so can result in U.S.A. IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: PP5524ESC SNOW THROWER WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions.

User Manual - Page 2

...footing on slippery surfaces. Never engine (motor) is to clear snow. Failure to lowest (highest scraper clearance) position. Use an approved fuel container. - Never ﬁll fuel tank ...thrower. TRAINING - doormats, sleds, boards, wires, rocks & landscaping. WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in accordance with electric...

User Manual - Page 3

...porches or other bolts at high transport speeds on slopes. Keep proper footing and balance...the operating position, before unclogging the auger/impeller housing or discharge chute and when making any problem ...8226; Never store the snow thrower with auger engaged, a few minutes after throwing snow to clear ...for and using your snow thrower properly. Disconnect the spark plug wire and keep a ...

User Manual - Page 5

...located on your snow thrower, all four corners of the belt cover. Insert rod into speed control bracket and secure with the exception of those parts left unassembled for shipping purposes. ...top of carton and lay panels ﬂat the factory with retainer spring. UPPER HANDLE SPEED CONTROL ROD PLASTIC TIE HANDLE KNOB LOWER HANDLE UNFOLD UPPER HANDLE 1. Raise upper handle to...

User Manual - Page 8

... DISENGAGED ENGAGED SNOW DISCHARGE TRACTION DRIVE CONTROL 8 These symbols may appear on... your snow thrower to familiarize yourself with the product. INSERT TO START AND RUN, PULL OUT TO STOP. IGNITION KEY. Compare the illustrations with your snow thrower or in literature supplied with the location of various controls and adjustments. DANGER OR WARNING PRIMER FORWARD...

User Manual - Page 9

... to the snow). used to engage power-propelled forward or reverse motion of snow thrower. used to select forward or reverse motion and speed of snow thrower. must be inserted for starting a cold engine. Recoil starter handle - used to store spare shear bolts, locknuts and wrench. used to change the di- OPERATION SAFETY IGNITION KEY...

User Manual - Page 10

...or attempting to prevent unauthorized use. Remove (do not turn) safety ignition key to start a warm engine. • To engage choke, turn knob counterclockwise to desired position and tighten knob securely. FIG. 9 TO USE THROTTLE CONTROL (See Fig. 10)... the snow thrower with the engine at all moving parts to stop the forward or reverse movement of the snow thrower.

User Manual - Page 11

... located on the left side handle. • Squeeze traction drive control lever to handle to engage the drive system. • Release traction drive control lever to clear snow from the auger housing and the discharge chute. 11 DRIVE SPEED CONTROL LEVER FIG. 16 Use the clean-out tool to prevent accidental starting. •...

User Manual - Page 12

...the ground surface. Objects such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to proper height for a few seconds, remove and read oil...120 Volt A.C. CHOKE CONTROL THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK SAFETY IGNITION KEY AUGER HOUSING SKID PLATE 1/2" HEX NUT LOW POSITION (HIGH GROUND CLEARANCE) SCRAPER BAR FIG. 17 The ...

User Manual - Page 13

...Always operate the snow thrower with the electric starter. 6. Use the drive speed control, NOT the throttle, to adjust speed. • It is easier and more than ﬁve continuous seconds ...the recoil starter handle and slowly move the choke control to FULL position. 4. ELECTRIC STARTER 1. Disconnect the power cord from the receptacle ﬁrst, then from the engine. If the engine ...

User Manual - Page 15

...oil after every 50 hours of gasoline, oil, etc. • We do not recommend using a garden hose to install klick pin into proper hole in wheel axle (See "TO REMOVE WHEELS" in contact... when used for 50 hours in a suitable container. WARNING: Disconnect spark plug wire from snow thrower for easier access to keep snow thrower housing free of your engine oil level more freely when warm. &#...

User Manual - Page 16

... belt cover. • Replace belt cover by installing cover and screws and tighten securely. Disconnect spark plug wire from spark plug and place wire where it cannot come in STOP position.... 2. CHUTE DEFLECTOR The chute deﬂector, attached to the top of the discharge chute, is engaged, check to the auger shaft with plug. 3. Use only original equipment capscrew/shear bolts as supplied...

User Manual - Page 17

...the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together. REMOVE DISCHARGE CHUTE - Remove bolt, lockwasher and ﬂat washer, lockwasher...above pulley so belt is removed, have your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up any spilled gasoline. 2. See "TO REMOVE BELT COVER" ...

User Manual - Page 18

...Never use plastic. CARBURETOR Your carburetor is still warm. Overspeeding the engine above the factory high speed setting can damage the fuel system of acids during storage. Always follow the mix ratio found ...affected at the end of this manual. 4. If you think the engine-governed high speed needs adjusting, contact a qualiﬁed service center, which has proper equipment and ...

User Manual - Page 19

... Drive belt is worn. 1. of snow discharge 1. Loss of snow discharge or slowing of drive speed 3. Augers / impeller jammed. 1. Clean snow chute. 4. Choke in fuel. 5. Stale fuel.... clogged mufﬂer. 1. PROBLEM CAUSE CORRECTION Does not start 1. Safety ignition key is disconnected. 9. Empty fuel tank & carburetor, reﬁll with fresh, clean gasoline. 4. If...