Poulan PLN3516F Support Question
Poulan PLN3516F Support Question
Find answers below for this question about Poulan PLN3516F.Need a Poulan PLN3516F manual? We have 2 online manuals for this item!
Question posted by moais on November 29th, 2019
Brake Repair
Hi,i broke the brake on the chainxsaw, a poulan PLN3516F, can't find parts for it! is there any place i can get the replacement pin
Supporting Image
You can click the image below to enlarge
Current Answers
Answer #1: Posted by freginold on November 29th, 2019 9:24 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
The following sites all carry replacement parts for the Poulan PLN3516F:
- eReplacementParts.com
- PartsTree.com
- JacksSmallEngines.com
- RepairClinic.com
If the part you need can't be found on any of those sites, contact the manufacturer to see if that part is still available and if so, where it can be purchased.
- eReplacementParts.com
- PartsTree.com
- JacksSmallEngines.com
- RepairClinic.com
If the part you need can't be found on any of those sites, contact the manufacturer to see if that part is still available and if so, where it can be purchased.
Related Poulan PLN3516F Manual Pages
User Manual - Page 1
... el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad.
s
Veuillez ne pas retourner l'outil au detaillant.
1-800-554-6723
www.poulan.com
Instruction Manual
Manual de Instrucciones
Manuel d'Instructions
PLN3516F rn Ch 13 > Z.1 O r-
245157
a WARNING:
C
US
A Read and follow all Safety Rules and Operating Instructions before
using this product.
User Manual - Page 2
... Start Saw
4-2. Chain Maintenance Instructions
7 BAR / CHAIN MAINTENANCE
17
7-1. Chain Replacement Information
8 LIMITED WARRANTY
18
2 Other Safety Precautions
2-4. INTRODUCTION
TABLE OF CONTENTS.../ CHAIN MAINTENANCE
15
6-1. Felling
5-2. Guide Bar Maintenance
6-2. CHAIN BRAKE"'/ Hand Guard
4-5. Extension Cords
5 GENERAL CUTTING INSTRUCTIONS
13
5-1. ...
User Manual - Page 3
... to help you locate the safety feature.
3 TRIGGER START / STOP SWITCH stops saw motor when released.
7 ELECTRIC MOTOR is double insulated for added safety.
9 CHAIN BRAKE LEVER / HAND GUARD activates the chain brake and protects the operator's left hand in the event saw chain breaks or derails during operation.
User Manual - Page 4
... The pointed tooth or teeth for a chain brake.
9. A device that when operated will complete...Chain Oil Capacity Net Weight (Without guide bar and chain)
4
PLN3516F 120V-, 60Hz, 13.5 Amp 3.5HP 5500/min 16" (40cm... saw and maintain position while sawing. 22. REPLACEMENT SAW CHAIN - SAW CHAIN - SWITCH LINKAGE ... The toothed part that cut in performing the bucking and felling cuts.
...
User Manual - Page 5
...will not be whipped toward you or pull you have repaired by authorized service facility. GUARD AGAINST ELECTRIC SHOCK: Prevent ... when the tension in a dry, and high or locked-up place - Worst-case computed kickback angle.
2. Avoid bar nose contact....let visitors contact the chain saw to contain long hair.
11. REPLACEMENT PARTS - All visitors should be kept away from the work area, secure...
User Manual - Page 6
...repaired or replaced by the manufacturer or the equivalent. MAINTAIN EXTENSION CORDS. Inspect the extension cords periodically and replace if damaged. Keep all times. CHECK DAMAGED PARTS...kickback chain, guide bar nose guards, chain brakes and special guide bars that is running....hand! Cut at
all parts of the saw is damaged should be
restricted to a Poulan Authorized Service Center. ...
User Manual - Page 7
...make inoperative any safety device furnished with your employer should be used ; The CHAIN BRAKE®/ Hand Guard is intended for prolonged use involves prolonged periods of doors. Safety...saw chain and be alert because rotational kickback and pinch kickback are no user serviceable parts inside.
16. See section 1-6 for starting the chain saw and control the ...repair it is tripped.
17.
User Manual - Page 8
....
•
Read and understand the instruction manual before using
the chain saw.
Hearing protection should be other replacement components for achieving Kickback protection.
Tip contact may cause serious injury.
44 1 Always use only identical replacement parts. IDENTIFICATION OF SAFETY SYMBOLS
A WARNINGI This chain saw , which may cause the guide bar to water or...
User Manual - Page 9
... counter-clockwise and then turn knob (B) counter-clockwise. (Fig. 3-3A) 3. ASSEMBLY INSTRUCTIONS
3-1. Place power unit on figure 3-4A. To remove the sprocket cover (A), turn the chain tension ring (C)... souce before the unit is designed for occasional homeowner use and should not be used for replacing a bar. Turn the knob clockwise, adjust the chain tension ring (F) and then tighten ...
User Manual - Page 10
... CHAIN TENSION:
With no dirt gets into the oil tank. NOTE: Make sure the CHAIN BRAKE is easy. Then turn ring (F) counter dock wise to loosen chain or clock wise to ...Wipe up and then tighten the bar bolt knob (E).
3-4B
3-4C
3-5. We recommend using Genuine Factory Parts Chain, Bar and Sprocket Oil, which contains additives to be frequently checked during , any spills.
While tensioning...
User Manual - Page 11
SELECTING THE PROPER EXTENSION CORD FOR YOUR SAW MODEL
Saw Model PLN3516F
Ampere Rating
13.5
Minimum Gauge Wire
Volts AC
Length of the extension...4-1. TO START SAW 1. Thumbs and fingers should encircle both hands, left hand holding the front handle (DO NOT HOLD CHAIN BRAKE®) and the right hand holding the rear handle. With your saw , release the trigger (Figure 4-1D). Plug the ...
User Manual - Page 12
... BRAKE® I HAND GUARD This Poulan chain saw is clear of the saw motor will not start if the CHAIN BRAKE® is activated, chain movement abruptly stops and the power supply to restart the motor.
4.3. B.
WARNING / CAUTION
A loose chain can be checked in period. This is evidenced by smoke or bar discoloration. Place...
User Manual - Page 13
...your right hand. For service information, contact the Poulan Product Service Department toll-free number listed on the ... stop when the CHAIN BRAKE® is felled. While the motor is ...Replace or repair any
damaged or frayed extension cords before making any cuts are ready to the nearest Authorized Service Center. WARNING
Your double insulated appliance has no serviceable parts...
User Manual - Page 15
...where to meet first cut from above (overbuck) to purchase a lube gun, contact the Poulan Product Service Department toll-free number listed on both ends: First, overbuck 1/3 diameter of ...into the ground (Figure 5-3A).
2.
Lubrication of cutting, the correct position for lubrication: Poulan Lube Gun
(disposable) This grease gun is recommended after each saw firmly with both hands...
User Manual - Page 16
...guide bar frequently at regular intervals (for dealing with a chain that the CHAIN BRAKED is removed.
6-2. CHAIN MAINTENANCE
INSTRUCTIONS
WARNING
Unless you have the kickback reducing guard... which may cause chain clatter and difficulty in making straight cuts. Always use a replacement saw chain designed as total protection against injury. Lubrication can be prevented merely by an...
User Manual - Page 17
...shorten the chain. Clean with Genuine Factory Parts Chain, Bar and Sprocket Oil.
BREAKINGIN A... removed from overheating.
The CHAIN BRAKE'S/Hand Guard and low-kickback saw...as five (5) cuts.
See your protection. Place switch in period, and the interval between future...appliance.
1. WARNING / CAUTION
Never have this repair performed. No grounding means is necessary. Do ...
User Manual - Page 18
... agrees to repair it yourself. Should you may be other quality equivalent replacement components for achieving kickback protection.
8 - If the saw . This warranty does not cover parts that each...any purchaser.
18 Check the power supply for repair or replacement at any time without notice or obligation to any defective Poulan brand electric product within the limited warranty period, ...
Parts List - Page 1
... - Chain Catcher Kit -
Oil Tank Cap Kit - Sprocket Kit -
Bar Clamp Scabbard
= New Part Number For This IPL
Ref.
Description
Not Shown 115367826 Manual
= Refer to design changes. Adjuster Wheel Bar Chain Screw Assy -
MODEL
PLN3516F
Page: 1
1
3
2
4
5
WARNING
All repairs, adjustments and maintenance not described in the Operator's Manual must be performed by...
Similar Questions
Inner Sprocket Gear For The Pln3516f
The inner gear is worn and I can't find any replacement parts.
The inner gear is worn and I can't find any replacement parts.
(Posted by rodneyedney 7 months ago)
Chain Off Sprocket
the chain on my pln3516f came off the sprocket and I can't get it back on. How do i get it back on t...
the chain on my pln3516f came off the sprocket and I can't get it back on. How do i get it back on t...
(Posted by nephron44 3 years ago)
Poulan Pro Pb18542lt Will Not Go Into Reverse
My lawn mower works fine going forward, but will not move when placed in reverse. What could be the ...
My lawn mower works fine going forward, but will not move when placed in reverse. What could be the ...
(Posted by tretta11 8 years ago)
Change Blade Poulan Pln3516f
how to change blade on poulan model pln3516f
how to change blade on poulan model pln3516f
(Posted by jackfrost69 9 years ago)