Pioneer GM-3500T Support Question
Pioneer GM-3500T Support Question
Find answers below for this question about Pioneer GM-3500T.Need a Pioneer GM-3500T manual? We have 1 online manual for this item!
Question posted by pnmbute on July 3rd, 2012
Power Supply
CAN I USE A LAPTOP POWER SUPPLY 16V BECOUSE I WANT TO USE THE GM IN MY ROOM FOR NOW AND AM CONNECTING ITS NOT WORKING BT THE POWER LIGHT IS ON.
Current Answers
Related Pioneer GM-3500T Manual Pages
Owner's Manual - Page 2
...and is in Your Hands
Get the most importantly, without distortion. ! Use caution or temporarily discontinue use , please read and observe WARNINGs and CAUTIONs in this manual. Information to... your product. Once you refer to higher volumes of Canada, Inc.
U.S.A.
Do not use of Your Ears is illegal in potentially hazardous situations. ! The Safety of headphones may invalidate...
Owner's Manual - Page 3
...car body.
! Always disconnect the negative * terminal of the amplifier and any abnormality, the power supply to the amplifier is cut off to prevent equipment malfunction. Extended use a fuse of the car stereo...English
Before connecting/ installing the amplifier
WARNING
! This unit is located on , the power indicator will turn off and check the power supply and speaker connections. Determine...
Owner's Manual - Page 4
... output remains low, even when the car stereo volume is turned down.
! Setting gain properly
! Relationship between amplifier gain and head unit output power
If amplifier gain is turned up, turn controls to control excess output.
! This eliminates high range frequency and outputs low range frequency. ! For use or improper connection.
! output of 4 V or more, adjust level...
Owner's Manual - Page 5
English
Section
02
En 5 Setting the unit
Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted with high output, if you raise the gain of the amplifier the power changes only slightly.
Owner's Manual - Page 6
... the positive (+) battery terminal.
2 Ground wire (Black) RD-223 (sold separately) Connect to metal body or chassis.
3 Car stereo with RCA output jacks (sold separately) After completing all other amplifier connections, finally connect the battery wire terminal of the power supply to feed power to Connections when using the speaker input wire on or off, which may malfunction. ! Never shorten...
Owner's Manual - Page 7
... or use a single 4 W speaker. Improper connection to the amplifier may result in malfunction or personal injury due to 8 W for a 4 W load or a single 4 W speaker per channel. For bridged mode for a two-channel amplifier, with a 4 W load, either wire two 8 W speakers in parallel for monaural and other amplifiers, please follow the speaker output connection diagram for stereo connection, or...
Owner's Manual - Page 8
...using the supplied speaker input wire. ! Do not connect both the RCA input and the
speaker input at the same time. Use pliers, etc., to crimp lugs to the terminal. Connect the battery wire directly to the car...
03 Connecting the units
Connections when using the speaker input wire
Connect the car stereo speaker output wires to the amplifier using the terminal screws, there is recommended.
Owner's Manual - Page 9
... expose about 10 mm (3/8 in.) of the speaker wires to wire ends. Connecting the units
Section
03
English
1 System remote control terminal 2 Ground terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire
Connecting the speaker output terminals
1 Use wire cutters or a utility knife to strip the end of wire and...
Owner's Manual - Page 10
... not touch any parts other than those supplied are used, they make temporary connections and check to be located. 2 Drill 2.5 mm (1/8 in.) diameter holes at a sufficiently rigid location.
! Secure the amplifier at the imprints either on the carpet or directly on the car model.
To ensure proper installation, use of a person in the vehicle as short...
Owner's Manual - Page 11
mum current drawn by this value when working out total current drawn by multiple power amplifiers. The average current drawn is input.
Specifications and the design are subject to
modifications without notice. ! Use this unit when an audio signal is nearly the maxi-
Power output 60 W RMS × 2 Channels (at 14.4 V, 2 W, 1 kHz, ≦ 1.0 % THD+N) Load impedance...
Similar Questions
Connecting To A Car Battery
Can you hook this up to two TS-D1002R speakers and power it with nothing but a car battery?
Can you hook this up to two TS-D1002R speakers and power it with nothing but a car battery?
(Posted by kochdenis1 12 years ago)
Power Light Flashing
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
(Posted by ntl1993 12 years ago)
Power Light Flashing
Why is the power light flashing and amp not working
Why is the power light flashing and amp not working
(Posted by kenstudebaker71 12 years ago)