Pfaff hobbymatic Support Question
Pfaff hobbymatic Support Question
Find answers below for this question about Pfaff hobbymatic.Need a Pfaff hobbymatic manual? We have 2 online manuals for this item!
Question posted by Inarestorer on August 23rd, 2014
Missing Stitches. Hobbymatic 939.
I have solved the problem of the thread breaking by changing the needle. However now when straight stitching, the machine misses several stitches every so often and every other stitch sometimes! I'm sure the solution is as simple as the last, can anyone advise please?
Current Answers
Related Pfaff hobbymatic Manual Pages
Owner's Manual - Page 1
A
Hobbymatic 800., 801, 802, 803, 806, 807 instruction book
Owner's Manual - Page 2
... the bobbin thread Presser bar lifter Thread cutter Regulating the stitch length Sewing straight stitches Zigzag stitches Needle position Selecting utility stitches, 802 to 807 Selecting stretch stitches, 806 and 807 Utility stitches, models 802 to 807 Stretch stitches, models 806, 807 Thread tensions Changing the needle Reverse sewing Dropping the machine feed Changing the sewing foot Sewing feet...
Owner's Manual - Page 4
... injure your fingers on the needle during sewing. Please note: When 13 amperes plug is the maximum size of this appliance may not correspond with the coloured markings identifying the terminals in your sewing machine
1 Take-up lever 2 Thread guide 3 Bobbin tension stud
(for bobbin winding) and thread guiding hook 4 Zigzag-stitch lever 5 Utility- The wires in...
Owner's Manual - Page 5
.... Foot control receptacle Remove this proce dure, making sure the bottom of the cover (G), move them back up (H) and
then remove the cover (I). J 1 On models 800, 802 and 806 place it into
the free arm.
7 -/ 800,802,806
4/-
Before putting the machine away after sewing replace the receptacle in the slot. To replace...
Owner's Manual - Page 6
Foot control Place the foot control on the floor under the table. The machine starts sewing. Electrical connection Push plug G into the machine socket and plug H into the wall socket. The more you press down with your foot. Press it down the pedal, the faster the
machine runs.
2 Your machine is now ready for sewing.
Owner's Manual - Page 11
.... Presser bar litter Lever 20 has three positions. G = The sewing foot is raised. (Before you until the needle moves down and up again and the take -up the bobbin thread Hold the needle thread a little taut.
Pull the bobbin thread out of the needle hole and lay both threads toward you
remove the work, turn the balance wheel...
Owner's Manual - Page 12
... length in mm.
Thread cutter (G) The thread cutter is set the stitch length control for sewing stretch stitches on the stitch length control.
Fig. H shows how to cut them. roDrbkraarwo.utthe threads into the cutter slot and pull them downwards to set at mark G on models 806 and 807.
/- tPhthueellpbtrhaeecskswe. Regulating the stitch length The stitch length is an...
Owner's Manual - Page 14
....vtstc5etlrhaieutttncnoyghttohittluhheletewhsnbeegoraletntehltqteco,uttmitioasernrerid(dn1sc1eottzhehritgereoFezcszitaghpeiq.geno-zbwtnaredeigldio-ntowhgf.). and stretch-stitch 5 should only be turned in the red sector on the machine and
explained on mTisutw(tnahtshhtiondiaeeteelddnciiecthltevgyeatlFa-rhattspetierpegeaiaed8opr.nnn)0zued.ec6iinsaglsoSrstzartagsertanrrrentregeedeitdnstct...
Owner's Manual - Page 17
As long as you button depressed, the machine
keep sews
this
backwards. Dropping the machine feed Push drop-feed button 22 to G.
'4
GH
13 embroidery,
darning etc.) For sewing, push the the bottom, and back
drop-feed button again to position
to The feed dog is dropped (for
position H. Reverse sewing Push button 12.
CRnSnsaieneyhadeedisaesddtneellpogemeutfi,hnsoielhg1tous3otnti0sthsedh...
Owner's Manual - Page 20
... against screw N.
The zipper foot can be adjusted sideways for straight stitching. This determines the buttonhole length.
16 Tighten screw L.
lever
Insert the filler cord as follows (Fig. As you sew, arrow L moves along the right or left zipper chain. H = Darning foot Raise the needle bar.
Push bracket M toward the back and hold it...
Owner's Manual - Page 23
...case. Changing the Switch off the
light bulb electric current
to
the
machine. Insert the new its pins slide in front of you. Clean round the sewing hook and the
the parts machine
fDdneraoeondpnceowo-... J).
19 Pull out the plug. On models 801, screws and needle plate
remove cover 15 803, 807: remove (Fig. Tilt the machine back and turn
it
so
that turn it and pull it towards...
Owner's Manual - Page 24
... stitches Needle not inserted correctly. Needle bent and strikes needle plate because work alone. Insert system 130/705 H needle. Select needle according to Needle and Thread Chart. Use only good-quality thread.
Machine threaded improperly. Needle thread breaks For any of the above . Needle bent. Needle too thin or too thick. See par. 1 above reasons. Check Needle and Thread...
Owner's Manual - Page 13
... inferiore sotto II piedino, (circa 10 cm).
4 Verschbub3klappe 119 schlieb3en.
Pull out the bobbin thread by means of the needle
thread.
Place both threads towards you and sew a stitch until both needle and take-up lever are up the bobbin thread: Hold the needle thread taut. Close free-arm cover 119. Fermer be capot 119. Turn the hand wheel towards...
Owner's Manual - Page 18
As long as you hold this button the machine sews back wards. Reverse sewing Press button 123. La cucitura indietro Premere ii tasto 123. Finchè II tasto rimane premuto Ia macchina cuce indietro.
Couture en marche arriè...
Owner's Manual - Page 23
... the left needle position (see page 25). The letters of finger-tip controls and programs.
A, B, C; This chart also contains possible applications. D Elastic triple zigzag stitch, 2 mm 2-mm zigzag stitch
E Elastic triple zigzag stitch, 3.5 mm 3.5-mm zigzag stitch
F Elastic triple zigzag stitch, 5 mm 5-mm zigzag stitch
G Elastic triple straight stitch Straight stitch
H Pullover stitch Blindstitch...
Owner's Manual - Page 27
... dei pro grammi ed alla fine di queste istruzione con indicazioni per le cuciture. The stitch combinations, together with some useful sewing tips, can be found in the programme table as well as at the end of stitch combinations, several finger-tip controls are pressed simultane ously.
Utility-
Combinalsons de points elastlques et...
Owner's Manual - Page 40
... du fil a coudre fin.
4 Regolazione per occhielli. Set the stitch density at range 3 for buttonhole sewing. This is how the buttonhole length is held in den Knopflochberech bel 3 stellen. Dadurch kann die Knopflochlänge bestimmt wer den. Set the needle thread tension at range N. During sewing, arrow Q runs along scale A. Stichdichte rn Knopflochbereich N einstellen...
Owner's Manual - Page 67
... and bottom of adjustment. Insert thicker needle.
Regulate thread tension.
Thread machine properly and check both tensions. Needle bent or blunt. Poor-quality or knotty thread used .
2. Needle breaks Needle not pushed up as far as it will go . Insert new needle and push it up as far as it will go . Machine threaded improperly. Needle thread breaks For any of above . Insert...
Owner's Manual - Page 68
.... piece of fabric under the sewing a short while, be sure to leave the machine, even for the master switch. rows of oil into hook raceway.
7. Machine feeds irregularly or not at right.)
Flick drop-feed control to the left.
6.
Remove thread ends and put a drop of feed dog.
Machine runs with difficulty Thread ends in hook raceway...
Owner's Manual - Page 76
...
Blindstitching
Bobbin winding
Bobbin winding preparations
Changing the bulb
Changing the needle
Changing the sewing foot Checking the bobbin thread tension Checking the needle thread tension
Cleaning and oiling
Darning with straight stitches
Darning with Disengaging
wool and engaging
the
sewing
mechanism
Drawing up the bobbin thread
Dropping the feed
Electrical connection Fancy...
Similar Questions
Edge Guide - Pfaff Select 1540 Sewing Machine
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
(Posted by jesjames 1 year ago)
Pfaff Hobbymatic 875 Foot Controller.
Good morning, my dog shewed the wires of my Pfaff Hobbymatic 875 foot controller.
Good morning, my dog shewed the wires of my Pfaff Hobbymatic 875 foot controller.
(Posted by celwolf429 2 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
Blindstitching A Hem Without A Blindstitching Foot
I no longer have the manual for my Pfaff Hobbymatic 939 machine.There is a button for blind stitchin...
I no longer have the manual for my Pfaff Hobbymatic 939 machine.There is a button for blind stitchin...
(Posted by maureen79815 8 years ago)
Problem Upper Presser Foot On Pfaff Hobbymatic 935 Sewing Machine
The upper presser foot on my Pfaff Hobbymatic 935 will not lower completely. I lowered the arm but t...
The upper presser foot on my Pfaff Hobbymatic 935 will not lower completely. I lowered the arm but t...
(Posted by Anonymous-118282 10 years ago)