Home » Pfaff » Sewing Machines » Pfaff hobbylock 4764

Pfaff hobbylock 4764 Support Question

Find answers below for this question about Pfaff hobbylock 4764.
Need a Pfaff hobbylock 4764 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by dbld84257 on September 11th, 2017

Where Can I Get The Blown-up Sheet Showing How To Thread My 4764? The Illustrati

the illustration in the op manual is too small for these old eyes. Thank you

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Pfaff hobbylock 4764 Manual Pages

Owner's Manual - Page 3

.... Use only attachments recommended by the manufacturer as threading needle, changing needle, threading bobbin, or changing presser foot, etc. • Always unplug sewing machine from outlet. • Do not unplug by or... safety precautions should never be left unattended when plugged in this manual. • Never operate this sewing machine if it has a damaged cord or plug, if it is not...

Owner's Manual - Page 4

... 4 1-1 Parts of hobbylock 4764 4 1-2 Accessories ...5 1-3 Connecting the foot control and the electrical connection 6 1-4 Setting telescopic thread stand 7 1-5 Opening and closing front cover and side cover 7 1-6 Changing the needle 8 1-7 Changing the presser foot 8 2Threading 8 2-1 Threading ...8 2-2 Changing thread 10 2-3 Test sewing ...12 3Sewing 12 3-1 4-thread overlock stitch using...

Owner's Manual - Page 5

Its ease of sewing fabrics, needles and machine settings 29 7Specifications 30 8Index 31 Congratulations! turning your new Pfaff® hobbylock™ 4764! Before you professional sewing results! 5Sewing problems and their solutions 28 6Table of use your Pfaff hobbylock 4764. Congratulations on purchasing your ideas into reality will give you start, please spend some time ...

Owner's Manual - Page 6

1. Summary 1-1 Parts of hobbylock 4764 1 2 3 4 5 6 7 8 9 17 1 2 34 10 11 12 13 14 15 16 1 Spool pin 2 Presser foot lift 3 Thread take up lever 4 Adjustment knob for presser foot pressure 5 Thread guides 6 Telescopic thread guide 7-1 Left needle thread tension 7-2 Right needle thread tension 7-3 Thread tension/upper looper 7-4 Thread tension/lower looper 8 Front panel 9 Swivel table ...

Owner's Manual - Page 7

1 2 3 4 8 5 6 7 13 12 1-2 Accessories 1 Thread unreeling discs (4 pcs.) 2 Tweezers 3 Machine oil 4 Lower blade 9 5 Needles # 11 (75) 6 Needles # 14 (90) 7 Screwdrivers 10 8 Convertor 9 Thread nets 11 10 Cleaning brush 11 Needle plate for rolled hem 12 Accessory box 13 Waste tray 14 Machine cover 14 5

Owner's Manual - Page 8

...off , the machine will not operate even with overlock machine Model 4764. The harder you press the foot control, the faster the machine runs. To reduce the risk of the machine). When the...use; For the USA and Canada This sewing machine has a polarized plug (one way. Note: Specifications vary from country to country. or servicing/ cleaning the machine. • Use foot control type YC...

Owner's Manual - Page 9

1-4 Setting telescopic thread stand Extend the telescopic thread stand to its full height, then turn until it downwards. How to open the side cover Push the cover to...front cover Push the cover to the right as far as it will not sew when the front cover is not closed all the way. The front cover has a safety switch and the machine will go and pull it locks. How to close the front cover Pull ...

Owner's Manual - Page 10

... by turning the handwheel towards you. 3. Use standard home sewing machine needles size #11 (#75) or #14(#90). 1-7 Changing presser foot Turn the machine off . 4. Push the red button and the foot will... with the pin right underneath the groove of the needle bar. Threading 2-1 Threading When threading the machine from you . 2. Loosen the needle clamp screw and remove two needles together. ...

Owner's Manual - Page 12

... the cutting position before start sewing. Cut the thread in the direction of your machine. 2-2 Changing thread The following is returned to change threads; 1. Take the thread drawn from front to the end of thread tail. 4. Place the new thread on the spindle and tie it through thread guides (1)-(7) (Fig. C). Left needle threading (D) Take the thread drawn from spool, and pass...

Owner's Manual - Page 13

... unwind from the spool, slip the net over the thread from the bottom of the needle. To make threading easier, use tweezers. When using standard thread spool, insert the thread unreeling discs (supplied with the machine) as shown. Raise the presser foot. 3. Reset tensions after you have threaded the loopers. 4. Set tensions to about 2 mm between...

Owner's Manual - Page 14

...: For thin and middleweight fabrics, there is any fabric or waste thread stuck between the blades. Check all 4 threads and applying slight tension. 3. If all 4 threads do not wind around the stitch finger of the blade. 2-3 Test sewing Ensure that each thread is complete, sew a few inches of chain stitches. If it is not set correctly...

Owner's Manual - Page 15

... gently backwards and to push it out roughly as the machine is called chaining off). This is operating and make chain stitches. For a neater finish, pull thread ends back through the seam using hook or yarn needle. 13 Beginning and end of sewing Place your left hand on the fabric to the left...

Owner's Manual - Page 16

...thickness. Adjustment is pre-adjusted for fabrics of the fabrics). Tighten Loosen Thread tension adjustment Adjust thread tension to suit the type of fabric and size of the presser ...on very thin or very thick fabrics. Accordingly, sew thinner fabrics with less pressure and thicker fabrics with same tension (both looper threads should not be well balanced with more pressure. ...

Owner's Manual - Page 19

...stitch width, turn the stitch width adjustment dial to the fabrics and threads (see table on p. 20). 17 This figure shows that the stitch width between the left needle and the edge of ... hemming) to 5 mm by adjusting the stitch length adjustment lever. Stitch length adjustment The machine is used for heavier fabrics. Typically, wider stitch widths are used only for regular seaming ...

Owner's Manual - Page 20

... waste tray to the right leg of arrow. 3-3 3-thread overlock stitch using 1 needle Though this machine is used mainly for decorative purposes. 18 Turn the left hand, at the same time, apply a little pressure in the opposite direction with your right hand as illustrated. Sewing curved seams For inside curves, guide the fabric gently...

Owner's Manual - Page 24

... lightweight fabrics. Set the stitch length adjustment lever to roll hem 3-thread rolled hem Rolled hemming is achieved by adjusting 1.5 the thread tensions, so that the fabric is overlocked while rolling underneath at 1.5 mm width. This is for normal sewing). For rolled hem sewing, use the needle plate marked "B" (the needle plate "A" is ideal...

Owner's Manual - Page 25

... Rolled hem (folded) Top side Underside Underside Stitch Width Rolled hem Rolled (folded) hem 5.5mm 5.5mm Standard chart for rolled hemming (see p. 20). 2. Sew at an even speed with even feeding of the thread chain to 2-thread overlock (see p. 22). Use only the right needle and change the needle plate for rolled hem...

Owner's Manual - Page 30

... you call for service. Following cases are • Loosen needle thread 15 Puckering too tight tension • Improper threading • Rethread the machine 8-10 • Set differential feed 16 between 0.7-N 28 5. Problem Machine does not sew Machine does not feed properly Needle breaks Breaking threads Skipping stitches Irregular stitches Cause Solution • Not plugged in...

Owner's Manual - Page 31

... fabric (cotton, wool) Needle HAx1SP HAx1T #11 (130/705H) (75) (For home-use sewing machine) #11 or #14 (75) or (90) Heavy fabric (denim, jersey) #14 (90) Thread • Polyester (spun filament) • Twisted thread #60/2~#80/2 • Twisted thread #80/3~#100/3 (3-thread overlock) • Twisted thread #60/2 (3- or 4-thread overlock) • Twisted thread #60/2~#50/2 (3-

Owner's Manual - Page 32

Speciﬁcations Number of threads 4-threads (3-, 2-threads) Number of needles Needles Width between two needles 2 needles (1 needle) Organ HAx1T #11, #14 (SCHMETZ 130/705H #75, #90) 2 mm Stitch width Standard 4.5 mm (Range 4.2-6.2 mm) Stitch length 1 - 4.4 mm Differential feed 0.7 - 2 Maximum sewing speed 1200 RPM Machine dimensions Weight Width 290mm Depth 220mm Height 330mm (...