Home » Pfaff » Sewing Machines » Pfaff hobbylock 4752

Pfaff hobbylock 4752 Support Question

Find answers below for this question about Pfaff hobbylock 4752.
Need a Pfaff hobbylock 4752 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by truthseeker71 on September 21st, 2022

Pfaff Hobbylock 4752

Which needles can I use for the Pfaff Hobbylock 4752?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on September 21st, 2022 9:06 PM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,621,300

1,100
points

https://www.manualslib.com/manual/505043/Pfaff-Hobbylock-4752.html?page=24

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff hobbylock 4752 Manual Pages

Owner's Manual - Page 1

hobbylock 4752 Instruction Manual

Owner's Manual - Page 2

Parts of the hobbylock 4752 Right needle thread tension (green) Setting screw for presser foot pressure Left needle thread tension (blue) Swivel plate Upper looper thread tension (red) Lower looper thread tension (yellow) Looper cover Telescoping thread guide Thread guides Thread spool pin ...

Owner's Manual - Page 5

... thick and thin for you start sewing, please take any further questions, just ask your very own fashions and projects! 3 Your dealer is to read these instructions carefully. Your PFAFF hobbylock features the very latest in its features. Your new hobbylock 4752 can do and make full use of service with any help or advice. We...

Owner's Manual - Page 6

... 7 Differential feed 20 Electrical power master switch 7 Foot control 7, 8 Handwheel 8 Light bulb (sewing lamp), changing 41 Looper cover 8 Lubricating the machine 39 Maintenance 38 - 41 Needle holder 22 Needle plate, removing 38 Needle position 23 Needle, changing 22 Oiling the machine 39 Presser foot 9, 21 Presser foot lifter 9 Presser foot pressure 21 Presser foot, changing 21...

Owner's Manual - Page 7

Seam width, setting 19 Securing the seam 27, 28 Sewing 26 Sewing light cover 41 Sewing problems and their solutions 42, 43 Specifications 44 Stitch ...aid for looper thread 13, 15 Threading aid for needle thread 16, 18 Threading paths/overview 0 Threading the lower overedge looper (yellow 14, 15 Threading the machine 10 Threading the needle(s 16, 17, 18 Threading the upper overedge looper...

Owner's Manual - Page 8

... unreeling discs wrench accessory box waste container Storing the accessory box Place the accessory box in the waste container. 6 looper threading aid machine oil replacement upper blade cleaning brush needle threading aid Accessories lug waste container groove looper cover Attaching the waste container Guide the lug into the groove on the looper...

Owner's Manual - Page 9

... This appliance has a polarized plug (one blade wider than the other ). For the USA and Canada This sewing machine has a polarized plug (one blade wider than the other ). Do not modify the plug in any way..... Foot controller type YC-482J (120 V)/YC-550 (230 V)/YC-551 (240 V) has to be used with this plug is designed to fit in the outlet, reverse the plug. If the plug does not fit...

Owner's Manual - Page 10

... activating the foot control. Closing: raise the looper cover and press it down , the faster the machine will sew. Closing: press the swivel plate towards the right and slightly towards the left. foot control handwheel Sewing speed The sewing speed is used. 8 Opening and closing the swivel plate Opening: press the swivel plate towards the...

Owner's Manual - Page 11

... thread tensioners when sewing rolled hems, pull the enclosed net over the spool, as shown in such a way that the slit is used. The two upper telescopes must always be rotated slowly until their locking balls are heard to its highest position. The presser foot must be lowered when the machine is at...

Owner's Manual - Page 13

... off. After threading, reset the thread tension to thread the needle threads, pull the thread ends through the loopers. Before the machine leaves the factory, threads are already threaded and their ends are... Therefore always make threading easier, set the thread tension to sew. In order to make sure that are perfectly threaded before beginning to "0". With this procedure, you...

Owner's Manual - Page 23

presser foot lifter lever needle presser foot holder lever clamp pin Removing the presser foot Turn the machine off. The presser foot will be adjusted for lightweight ... foot holder and press lever until the pin of the foot is properly locked into place. for normal sewing work in such a way that the pressser foot is directly under the presser foot holder clamp. Lift ...

Owner's Manual - Page 25

... fall out. Changing the needle when sewing with three threads Undo both needle fastening screws and remove the old needle. Remove the left needle and the left needle only (for 3-thread seams with a narrow seam width) Turn the machine off . Insert the new needle as far as it does not fall out. Use of the right needle only (for 3-thread...

Owner's Manual - Page 28

... distance from the needles. At the same time, pull the thread chain gently towards you and check the thread chain. Guide the sewing material in the illustration. The sewing material is not necessary to properly position your fabric when sewing. Finishing sewing When you have completed your seam, allow the machine to continue to sew slowly until...

Owner's Manual - Page 29

...of the seam using one of the seam 1. Thread the thread chain into a needle with a large eye and pull the thread chain into the fabric. 3. Raise the presser foot, guide the thread chain to sew. 5. Hold ... the presser foot towards the upper blade. Insert the sewing fabric into the machine and sew 2-3 stitches into the overlock stitches of the seam to prevent the seam from coming undone....

Owner's Manual - Page 43

... the lamp in and turn to OFF. Safety notes Only use bulbs with bare hands. Never touch the bulb with a maximum output of the machine, as shown in and turn to the sewing light cover until the cover can be removed. Transporting the machine Position your fingers in the cutout on the rear side...

Owner's Manual - Page 44

... (see Page 32 - 36). 42 Insert needle correctly (see Page 22). Sewing problems and their solutions This machine has been developed with ease of minor adjustment and operating errors. Thread breaks Incorrectly threaded. Use needle system HAx1SP (130/705 H-PS). The fabric was bent or the point damaged. Insert needle fully (see Page 22). Skipping stitches...

Owner's Manual - Page 45

... 10 - 18). The main switch is blunt. Thread correctly (see Page 21). Reduce sewing foot pressure (see Page 20). Clean the feed dog. Machine will not operate The lead cord/plug is not seated properly in the feed dog. Sewing foot pressure too high for heavy fabrics. Clean blades. Problem Cause Solution Fabric...

Owner's Manual - Page 46

Specifications Maximum sewing speed Seam width Stitch length Presser foot Lubrication Presser foot height Overedge stroke Needle system Needle size Number of threads Dimensions (width x height x depth) Weight Packing contents 1 machine 1 foot control 1 instruction manual/guarantee card 1 machine cover 1 accessory box 1 waste container 44 1200 stitches/min. 3.0 mm - 6.7 mm 1.0 mm - 5.0 mm ...

Owner's Manual - Page 51

Parts of the hobbylock 4752 Movable upper blade Upper overedge looper (red) Lower overedge looper (yellow) Fixed lower blade Thread chain cutter Presser foot lifter Needle plate Ridged knob for lowering the upper blade Setting knob for seam width Standard presser foot Bed slide for stitch width latch

Owner's Manual - Page 52